Thanks, Vaibhav Hiremath > -----Original Message----- > From: Sriram V [mailto:vshrirama@xxxxxxxxx] > Sent: Friday, April 17, 2009 5:57 PM > To: Hiremath, Vaibhav > Cc: video4linux-list@xxxxxxxxxx; linux-media@xxxxxxxxxxxxxxx > Subject: Re: [REVIEW PATCH 2/2] Added OMAP3EVM Multi-Media Daughter > Card Support > > Hi Vaibav, > I am using Sergio's patch that was posted on dec12th. > > I have been trying to apply the mdc driver patches + camera > drivers/isp drivers > patches related to mdc on sergio's dec 12th patches. > > They fail to apply at all. I would appreciate if you could send > me > those patches. > [Hiremath, Vaibhav] One thing I am not able to understand is, why you are referring to old code-base. I have refreshed the patches with the latest post from Sakari. Is there any specific reason for this? Can you please provide error log, so that I can directly help you resolving this? > > Regards, > sriram > > > > > > > On Wed, Jan 7, 2009 at 11:37 AM, <hvaibhav@xxxxxx> wrote: > > From: Vaibhav Hiremath <hvaibhav@xxxxxx> > > > > This is first version of OMAP3EVM Mulit-Media Daughter > > Card support. > > > > Tested: > > - TVP5146 (BT656) decoder interface on top of > > Sergio's ISP-Camera patches. > > - Loopback application, capturing image through TVP5146 > > and displaying it onto the TV/LCD on top of Hardik's > > V4L2 driver. > > - Basic functionality of HSUSB Transceiver USB-83320 > > - > > > > TODO: > > - Camera sensor support > > - Driver header file inclusion (dependency on ISP-Camera > patches) > > - Some more clean-up may required. > > > > Signed-off-by: Brijesh Jadav <brijesh.j@xxxxxx> > > Signed-off-by: Hardik Shah <hardik.shah@xxxxxx> > > Signed-off-by: Manjunath Hadli <mrh@xxxxxx> > > Signed-off-by: R Sivaraj <sivaraj@xxxxxx> > > Signed-off-by: Vaibhav Hiremath <hvaibhav@xxxxxx> > > --- > > arch/arm/mach-omap2/Kconfig | 4 + > > arch/arm/mach-omap2/Makefile | 1 + > > arch/arm/mach-omap2/board-omap3evm-dc.c | 417 > +++++++++++++++++++++++++++++++ > > arch/arm/mach-omap2/board-omap3evm-dc.h | 43 ++++ > > arch/arm/mach-omap2/mux.c | 7 + > > arch/arm/plat-omap/include/mach/mux.h | 4 + > > 6 files changed, 476 insertions(+), 0 deletions(-) > > mode change 100644 => 100755 arch/arm/mach-omap2/Kconfig > > mode change 100644 => 100755 arch/arm/mach-omap2/Makefile > > create mode 100755 arch/arm/mach-omap2/board-omap3evm-dc.c > > create mode 100755 arch/arm/mach-omap2/board-omap3evm-dc.h > > mode change 100644 => 100755 arch/arm/mach-omap2/mux.c > > mode change 100644 => 100755 arch/arm/plat- > omap/include/mach/mux.h > > > > diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach- > omap2/Kconfig > > old mode 100644 > > new mode 100755 > > index ca24a7a..094c97f > > --- a/arch/arm/mach-omap2/Kconfig > > +++ b/arch/arm/mach-omap2/Kconfig > > @@ -121,6 +121,10 @@ config MACH_OMAP3EVM > > bool "OMAP 3530 EVM board" > > depends on ARCH_OMAP3 && ARCH_OMAP34XX > > > > +config MACH_OMAP3EVM_DC > > + bool "OMAP 3530 EVM daughter card board" > > + depends on ARCH_OMAP3 && ARCH_OMAP34XX && MACH_OMAP3EVM > > + > > config MACH_OMAP3_BEAGLE > > bool "OMAP3 BEAGLE board" > > depends on ARCH_OMAP3 && ARCH_OMAP34XX > > diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach- > omap2/Makefile > > old mode 100644 > > new mode 100755 > > index 3897347..16fa35a > > --- a/arch/arm/mach-omap2/Makefile > > +++ b/arch/arm/mach-omap2/Makefile > > @@ -60,6 +60,7 @@ obj-$(CONFIG_MACH_OMAP3EVM) += board- > omap3evm.o \ > > usb-musb.o usb-ehci.o \ > > board-omap3evm-flash.o \ > > twl4030-generic- > scripts.o > > +obj-$(CONFIG_MACH_OMAP3EVM_DC) += board-omap3evm-dc.o > > obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board- > omap3beagle.o \ > > usb-musb.o usb-ehci.o \ > > mmc-twl4030.o \ > > diff --git a/arch/arm/mach-omap2/board-omap3evm-dc.c > b/arch/arm/mach-omap2/board-omap3evm-dc.c > > new file mode 100755 > > index 0000000..233c219 > > --- /dev/null > > +++ b/arch/arm/mach-omap2/board-omap3evm-dc.c > > @@ -0,0 +1,417 @@ > > +/* > > + * arch/arm/mach-omap2/board-omap3evm-dc.c > > + * > > + * Driver for OMAP3 EVM Daughter Card > > + * > > + * Copyright (C) 2008 Texas Instruments Inc > > + * Author: Vaibhav Hiremath <hvaibhav@xxxxxx> > > + * > > + * Contributors: > > + * Anuj Aggarwal <anuj.aggarwal@xxxxxx> > > + * Sivaraj R <sivaraj@xxxxxx> > > + * > > + * This package is free software; you can redistribute it and/or > modify > > + * it under the terms of the GNU General Public License version 2 > as > > + * published by the Free Software Foundation. > > + * > > + * This program is distributed in the hope that it will be > useful, > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > + * GNU General Public License for more details. > > + * > > + * You should have received a copy of the GNU General Public > License > > + * along with this program; if not, write to the Free Software > > + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. > > + * > > + */ > > + > > +#include <linux/module.h> > > +#include <linux/kernel_stat.h> > > +#include <linux/init.h> > > +#include <linux/i2c.h> > > +#include <linux/delay.h> > > +#include <linux/spinlock.h> > > +#include <linux/clk.h> > > +#include <linux/device.h> > > +#include <linux/io.h> > > +#include <linux/gpio.h> > > + > > +#include <mach/io.h> > > +#include <mach/mux.h> > > + > > +#if defined(CONFIG_VIDEO_TVP514X) || > defined(CONFIG_VIDEO_TVP514X_MODULE) > > +#include <linux/videodev2.h> > > +#include <media/v4l2-int-device.h> > > +#include <media/tvp514x.h> > > +/* include V4L2 camera driver related header file */ > > +#if defined(CONFIG_VIDEO_OMAP3) || > defined(CONFIG_VIDEO_OMAP3_MODULE) > > +#include <../drivers/media/video/omap34xxcam.h> > > +#include <../drivers/media/video/isp/ispreg.h> > > +#endif /* #ifdef CONFIG_VIDEO_OMAP3 */ > > +#endif /* #ifdef CONFIG_VIDEO_TVP514X*/ > > + > > +#include "board-omap3evm-dc.h" > > + > > +#define MODULE_NAME "omap3evmdc" > > + > > +#ifdef DEBUG > > +#define dprintk(fmt, args...) printk(KERN_ERR MODULE_NAME ": " > fmt, ## args) > > +#else > > +#define dprintk(fmt, args...) > > +#endif /* #ifdef DEBUG */ > > + > > +/* Macro Definitions */ > > + > > +/* System control module register offsets */ > > +#define REG_CONTROL_PADCONF_I2C2_SDA (0x480021C0u) > > +#define REG_CONTROL_PADCONF_I2C3_SDA (0x480021C4u) > > + > > +#define PADCONF_I2C3_SCL_MASK (0xFFFF0000u) > > +#define PADCONF_I2C3_SDA_MASK (0x0000FFFFu) > > + > > +/* mux mode 0 (enable I2C3 SCL), pull-up enable, input enable */ > > +#define PADCONF_I2C3_SCL_DEF (0x01180000u) > > +/* mux mode 0 (enable I2C3 SDA), pull-up enable, input enable */ > > +#define PADCONF_I2C3_SDA_DEF (0x00000118u) > > + > > +/* GPIO pins */ > > +#define GPIO134_SEL_Y (134) > > +#define GPIO54_SEL_EXP_CAM (54) > > +#define GPIO136_SEL_CAM (136) > > + > > +/* board internal information (BEGIN) */ > > + > > +/* I2C bus to which all I2C slave devices are attached */ > > +#define BOARD_I2C_BUSNUM (3) > > + > > +/* I2C address of chips present in board */ > > +#define TVP5146_I2C_ADDR (0x5D) > > + > > +/* Register offsets */ > > +#define REG_BUS_CTRL1 (0x00000180u) > > +#define REG_BUS_CTRL2 (0x000001C0u) > > + > > +/* Bit defines for Bus Control 1 register */ > > +#define TVP5146_EN_SHIFT (0x0000u) > > +#define TVP5146_EN_MASK (1u << > TVP5146_EN_SHIFT) > > + > > +#define CAMERA_SENSOR_EN_SHIFT (0x0008u) > > +#define CAMERA_SENSOR_EN_MASK (1u << > CAMERA_SENSOR_EN_SHIFT) > > + > > +/* default value for bus control registers */ > > +#define BUS_CONTROL1_DEF (0x0141u) /* Disable > all mux */ > > +#define BUS_CONTROL2_DEF (0x010Au) /* Disable > all mux */ > > + > > +#if defined(CONFIG_VIDEO_TVP514X) || > defined(CONFIG_VIDEO_TVP514X_MODULE) > > +#if defined(CONFIG_VIDEO_OMAP3) || > defined(CONFIG_VIDEO_OMAP3_MODULE) > > +static struct omap34xxcam_hw_config decoder_hwc = { > > + .dev_index = 0, > > + .dev_minor = 0, > > + .dev_type = OMAP34XXCAM_SLAVE_SENSOR, > > + .u.sensor.xclk = OMAP34XXCAM_XCLK_NONE, > > + .u.sensor.sensor_isp = 1, > > +}; > > + > > +static struct isp_interface_config tvp5146_if_config = { > > + .ccdc_par_ser = ISP_PARLL_YUV_BT, > > + .dataline_shift = 0x1, > > + .hsvs_syncdetect = ISPCTRL_SYNC_DETECT_VSRISE, > > + .vdint0_timing = 0x0, > > + .vdint1_timing = 0x0, > > + .strobe = 0x0, > > + .prestrobe = 0x0, > > + .shutter = 0x0, > > + .u.par.par_bridge = 0x0, > > + .u.par.par_clk_pol = 0x0, > > +}; > > +#endif > > + > > +static struct v4l2_ifparm ifparm = { > > + .if_type = V4L2_IF_TYPE_BT656, > > + .u = { > > + .bt656 = { > > + .frame_start_on_rising_vs = 1, > > + .bt_sync_correct = 0, > > + .swap = 0, > > + .latch_clk_inv = 0, > > + .nobt_hs_inv = 0, /* active high */ > > + .nobt_vs_inv = 0, /* active high */ > > + .mode = V4L2_IF_TYPE_BT656_MODE_BT_8BIT, > > + .clock_min = TVP514X_XCLK_BT656, > > + .clock_max = TVP514X_XCLK_BT656, > > + }, > > + }, > > +}; > > + > > +/** > > + * @brief tvp5146_ifparm - Returns the TVP5146 decoder interface > parameters > > + * > > + * @param p - pointer to v4l2_ifparm structure > > + * > > + * @return result of operation - 0 is success > > + */ > > +static int tvp5146_ifparm(struct v4l2_ifparm *p) > > +{ > > + if (p == NULL) > > + return -EINVAL; > > + > > + *p = ifparm; > > + return 0; > > +} > > + > > +/** > > + * @brief tvp5146_set_prv_data - Returns tvp5146 omap34xx driver > private data > > + * > > + * @param priv - pointer to omap34xxcam_hw_config structure > > + * > > + * @return result of operation - 0 is success > > + */ > > +static int tvp5146_set_prv_data(void *priv) > > +{ > > +#if defined(CONFIG_VIDEO_OMAP3) || > defined(CONFIG_VIDEO_OMAP3_MODULE) > > + struct omap34xxcam_hw_config *hwc = priv; > > + > > + if (priv == NULL) > > + return -EINVAL; > > + > > + hwc->u.sensor.sensor_isp = > decoder_hwc.u.sensor.sensor_isp; > > + hwc->u.sensor.xclk = decoder_hwc.u.sensor.xclk; > > + hwc->dev_index = decoder_hwc.dev_index; > > + hwc->dev_minor = decoder_hwc.dev_minor; > > + hwc->dev_type = decoder_hwc.dev_type; > > + return 0; > > +#else > > + return -EINVAL; > > +#endif > > +} > > + > > +/** > > + * @brief omap3evmdc_set_mux - Sets mux to enable/disable signal > routing to > > + * different peripherals present in > board > > + * IMPORTANT - This function will take care of writing > appropriate values for > > + * active low signals as well > > + * > > + * @param mux_id - enum, mux id to enable/disable > > + * @param value - enum, ENABLE_MUX for enabling and DISABLE_MUX > for disabling > > + * > > + * @return result of operation - 0 is success > > + */ > > +static int omap3evmdc_set_mux(enum omap3evmdc_mux mux_id, enum > config_mux value) > > +{ > > + int err = 0; > > + > > + if (unlikely(mux_id >= NUM_MUX)) { > > + dprintk("Invalid mux id\n"); > > + return -EPERM; > > + } > > + > > + > > + switch (mux_id) { > > + case MUX_TVP5146: > > + /* active low signal. set 0 to enable, 1 to > disable */ > > + if (ENABLE_MUX == value) { > > + /* pull down the GPIO GPIO134 = 0 */ > > + gpio_set_value(GPIO134_SEL_Y, 0); > > + /* pull up the GPIO GPIO54 = 1 */ > > + gpio_set_value(GPIO54_SEL_EXP_CAM, 1); > > + /* pull up the GPIO GPIO136 = 1 */ > > + gpio_set_value(GPIO136_SEL_CAM, 1); > > + } else > > + /* pull up the GPIO GPIO134 = 0 */ > > + gpio_set_value(GPIO134_SEL_Y, 1); > > + > > + break; > > + > > + case MUX_CAMERA_SENSOR: > > + /* active low signal. set 0 to enable, 1 to > disable */ > > + if (ENABLE_MUX == value) { > > + /* pull up the GPIO GPIO134 = 0 */ > > + gpio_set_value(GPIO134_SEL_Y, 1); > > + /* pull up the GPIO GPIO54 = 1 */ > > + gpio_set_value(GPIO54_SEL_EXP_CAM, 1); > > + /* pull down the GPIO GPIO136 = 1 */ > > + gpio_set_value(GPIO136_SEL_CAM, 0); > > + } else > > + /* pull up the GPIO GPIO136 = 1 */ > > + gpio_set_value(GPIO136_SEL_CAM, 1); > > + > > + break; > > + > > + case MUX_EXP_CAMERA_SENSOR: > > + /* active low signal. set 0 to enable, 1 to > disable */ > > + if (ENABLE_MUX == value) { > > + /* pull up the GPIO GPIO134 = 1 */ > > + gpio_set_value(GPIO134_SEL_Y, 1); > > + /* pull down the GPIO GPIO54 = 1 */ > > + gpio_set_value(GPIO54_SEL_EXP_CAM, 0); > > + /* pull up the GPIO GPIO136 = 1 */ > > + gpio_set_value(GPIO136_SEL_CAM, 1); > > + } else > > + /* pull up the GPIO GPIO54 = 1 */ > > + gpio_set_value(GPIO54_SEL_EXP_CAM, 1); > > + > > + break; > > + > > + case NUM_MUX: > > + default: > > + dprintk("Invalid mux id\n"); > > + err = -EPERM; > > + } > > + > > + return err; > > +} > > +/** > > + * @brief tvp5146_power_set - Power-on or power-off TVP5146 > device > > + * > > + * @param power - enum, Power on/off, resume/standby > > + * > > + * @return result of operation - 0 is success > > + */ > > +static int tvp5146_power_set(enum v4l2_power power) > > +{ > > + switch (power) { > > + case V4L2_POWER_OFF: > > +#if defined(CONFIG_VIDEO_OMAP3) || > defined(CONFIG_VIDEO_OMAP3_MODULE) > > + if (isp_free_interface(ISP_PARLL_YUV_BT)) > > + return -ENODEV; > > +#endif > > + /* Disable mux for TVP5146 decoder data path */ > > + if (omap3evmdc_set_mux(MUX_TVP5146, DISABLE_MUX)) > > + return -ENODEV; > > + break; > > + > > + case V4L2_POWER_STANDBY: > > + break; > > + > > + case V4L2_POWER_ON: > > + /* Enable mux for TVP5146 decoder data path */ > > + if (omap3evmdc_set_mux(MUX_TVP5146, ENABLE_MUX)) > > + return -ENODEV; > > + > > +#if defined(CONFIG_VIDEO_OMAP3) || > defined(CONFIG_VIDEO_OMAP3_MODULE) > > + if (isp_request_interface(ISP_PARLL_YUV_BT)) > > + return -ENODEV; > > + > > + isp_configure_interface(&tvp5146_if_config); > > +#endif > > + break; > > + > > + default: > > + return -ENODEV; > > + break; > > + } > > + return 0; > > +} > > + > > +static struct tvp514x_platform_data tvp5146_pdata = { > > + .master = "omap34xxcam", > > + .power_set = tvp5146_power_set, > > + .priv_data_set = tvp5146_set_prv_data, > > + .ifparm = tvp5146_ifparm, > > + > > + /* Some interface dependent params */ > > + .clk_polarity = 0, /* data clocked out on falling edge */ > > + .hs_polarity = 1, /* 0 - Active low, 1- Active high */ > > + .vs_polarity = 1, /* 0 - Active low, 1- Active high */ > > +}; > > + > > +static struct i2c_board_info __initdata tvp5146_i2c_board_info = > { > > + I2C_BOARD_INFO("tvp5146m2", TVP5146_I2C_ADDR), > > + .platform_data = &tvp5146_pdata, > > +}; > > + > > +#endif /* #ifdef CONFIG_VIDEO_TVP514X */ > > + > > +/** > > + * @brief omap3evmdc_mdc_config - GPIO configuration for > > + * GPIO 134, 54 and 136 > > + * > > + * @return result of operation - 0 is success > > + */ > > +static int omap3evmdc_mdc_config(void) > > +{ > > + /* Setting the MUX configuration */ > > + omap_cfg_reg(GPIO134_VDIN_SEL_Y); > > + omap_cfg_reg(GPIO54_VDIN_SEL_EXP_CAM); > > + omap_cfg_reg(GPIO136_VDIN_SEL_CAM); > > + > > + if (gpio_request(GPIO134_SEL_Y, "GPIO134_SEL_Y") < 0) { > > + dprintk("can't get GPIO 134\n"); > > + return -EINVAL; > > + } > > + > > + if (gpio_request(GPIO54_SEL_EXP_CAM, "GPIO54_SEL_EXP_CAM") > < 0) { > > + dprintk("can't get GPIO 54\n"); > > + return -EINVAL; > > + } > > + > > + if (gpio_request(GPIO136_SEL_CAM, "GPIO136_SEL_CAM") < 0) > { > > + dprintk("can't get GPIO 136\n"); > > + return -EINVAL; > > + } > > + > > + /* Make GPIO as output */ > > + gpio_direction_output(GPIO134_SEL_Y, 0); > > + /* Make GPIO as output */ > > + gpio_direction_output(GPIO54_SEL_EXP_CAM, 0); > > + /* Make GPIO as output */ > > + gpio_direction_output(GPIO136_SEL_CAM, 0); > > + > > + return 0; > > +} > > + > > +/** > > + * @brief omap3evmdc_init - module init function. Should be > called before any > > + * client driver init call > > + * > > + * @return result of operation - 0 is success > > + */ > > +static int __init omap3evmdc_init(void) > > +{ > > + int err; > > + > > + /* > > + * I2C3 SCL pin mux settings - mux mode 0, pull-up enable, > input enable > > + * Uses the MSB 16-bit of this register, retain the LSB > 16-bit. > > + * This pin is shared with gpio_184 (mux mode 4) > > + */ > > + omap_writel(((omap_readl(REG_CONTROL_PADCONF_I2C2_SDA) & > > + ~PADCONF_I2C3_SCL_MASK) | > PADCONF_I2C3_SCL_DEF), > > + REG_CONTROL_PADCONF_I2C2_SDA); > > + > > + /* > > + * I2C3 SDA pin mux settings - mux mode 0, pull-up enable, > input enable > > + * Uses the LSB 16-bit of this register, retain the MSB > 16-bit. > > + * This pin is shared with gpio_185 (mux mode 4) > > + */ > > + omap_writel(((omap_readl(REG_CONTROL_PADCONF_I2C3_SDA) & > > + ~PADCONF_I2C3_SDA_MASK) | > PADCONF_I2C3_SDA_DEF), > > + REG_CONTROL_PADCONF_I2C3_SDA); > > + > > + err = omap3evmdc_mdc_config(); > > + if (err) { > > + dprintk("MDC configuration failed \n"); > > + return err; > > + } > > + > > + /* > > + * Register each of the I2C devices present in the board > to the I2C > > + * framework. > > + * If more I2C devices are added, then each device > information should > > + * be registered with I2C using i2c_register_board_info(). > > + */ > > +#if defined(CONFIG_VIDEO_TVP514X) || > defined(CONFIG_VIDEO_TVP514X_MODULE) > > + err = i2c_register_board_info(BOARD_I2C_BUSNUM, > > + &tvp5146_i2c_board_info, > 1); > > + if (err) { > > + dprintk("TVP5146 I2C Board Registration failed > \n"); > > + return err; > > + } > > +#endif > > + > > + printk(KERN_INFO MODULE_NAME ": Driver registration > complete \n"); > > + > > + return 0; > > +} > > + > > +arch_initcall(omap3evmdc_init); > > diff --git a/arch/arm/mach-omap2/board-omap3evm-dc.h > b/arch/arm/mach-omap2/board-omap3evm-dc.h > > new file mode 100755 > > index 0000000..5eaffc5 > > --- /dev/null > > +++ b/arch/arm/mach-omap2/board-omap3evm-dc.h > > @@ -0,0 +1,43 @@ > > +/* > > + * arch/arm/mach-omap2/board-omap3evm-dc.h > > + * > > + * Copyright (C) 2008 Texas Instruments Inc > > + * Author: Vaibhav Hiremath <hvaibhav@xxxxxx> > > + * > > + * Contributors: > > + * Anuj Aggarwal <anuj.aggarwal@xxxxxx> > > + * Sivaraj R <sivaraj@xxxxxx> > > + * > > + * This package is free software; you can redistribute it and/or > modify > > + * it under the terms of the GNU General Public License version 2 > as > > + * published by the Free Software Foundation. > > + * > > + * This program is distributed in the hope that it will be > useful, > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > + * GNU General Public License for more details. > > + * > > + * You should have received a copy of the GNU General Public > License > > + * along with this program; if not, write to the Free Software > > + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. > > + * > > + */ > > + > > +#ifndef __BOARD_OMAP3EVM_DC_H_ > > +#define __BOARD_OMAP3EVM_DC_H_ > > + > > +/* mux id to enable/disable signal routing to different > peripherals */ > > +enum omap3evmdc_mux { > > + MUX_TVP5146 = 0, > > + MUX_CAMERA_SENSOR, > > + MUX_EXP_CAMERA_SENSOR, > > + NUM_MUX > > +}; > > + > > +/* enum to enable or disable mux */ > > +enum config_mux { > > + DISABLE_MUX, > > + ENABLE_MUX > > +}; > > + > > +#endif /* __BOARD_OMAP3EVM_DC_H_ */ > > diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c > > old mode 100644 > > new mode 100755 > > index dacb41f..5b878b6 > > --- a/arch/arm/mach-omap2/mux.c > > +++ b/arch/arm/mach-omap2/mux.c > > @@ -459,6 +459,13 @@ MUX_CFG_34XX("AH8_34XX_GPIO29", 0x5fa, > > OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT) > > MUX_CFG_34XX("J25_34XX_GPIO170", 0x1c6, > > OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT) > > + > > +MUX_CFG_34XX("GPIO134_VDIN_SEL_Y", 0x160, > > + OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT) > > +MUX_CFG_34XX("GPIO_54_VDIN_SEL_EXP_CAM", 0x0b4, > > + OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT) > > +MUX_CFG_34XX("GPIO136_VDIN_SEL_CAM", 0x164, > > + OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT) > > }; > > > > #define OMAP34XX_PINS_SZ ARRAY_SIZE(omap34xx_pins) > > diff --git a/arch/arm/plat-omap/include/mach/mux.h > b/arch/arm/plat-omap/include/mach/mux.h > > old mode 100644 > > new mode 100755 > > index f4362b8..2cd5cde > > --- a/arch/arm/plat-omap/include/mach/mux.h > > +++ b/arch/arm/plat-omap/include/mach/mux.h > > @@ -790,6 +790,10 @@ enum omap34xx_index { > > */ > > AH8_34XX_GPIO29, > > J25_34XX_GPIO170, > > + > > + GPIO134_VDIN_SEL_Y, > > + GPIO54_VDIN_SEL_EXP_CAM, > > + GPIO136_VDIN_SEL_CAM, > > }; > > > > struct omap_mux_cfg { > > -- > > 1.5.6 > > > > -- > > video4linux-list mailing list > > Unsubscribe mailto:video4linux-list- > request@xxxxxxxxxx?subject=unsubscribe > > https://www.redhat.com/mailman/listinfo/video4linux-list > > -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
