Hallo, my configuration is * Fujitsu Siemens HTPC * MythDora 5.0(FC 8) * TwinHan PCI-Sat * Technisat Multytenne(4 Satelite positions 13.0 19.2,23.5, 28) dual This mulitytenne is once connected to a technisat receiver and once to the HTPC. I can watch on the receiver, but I did not success with my htpc so far. The card is recognized in mythtv-setup, but it cant determine its parameters, so I tried to use it manually, first. I got installed 2 tv cards in my HTPC, I am concentrating on the Twinhan Vision Plus DVB In my /etc/modprobe.conf there is not yet anything mentioned about my dvb card ls /dev/dvb/adapter0/ shows ca0 demux0 dvr0 frontend0 net0 I successfully generated a channels.conf with valid and real channels. When I run [mythtv@localhost szap]$ ./szap -a 0 -r N24 reading channels from file '/home/mythtv/.szap/channels.conf' zapping to 17 'N24': sat 0, frequency = 12640 MHz V, symbolrate 22000000, vpid = 0x03ff, apid = 0x0400 using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' FE_SET_VOLTAGE failed: Input/output error status 1f | signal fffe | snr fffe | ber fffffffe | unc fffffffe | FE_HAS_LOCK status 1f | signal fffe | snr 22ef | ber fffffffe | unc fffffffe | FE_HAS_LOCK status 1f | signal 3d00 | snr 22f3 | ber fffffffe | unc fffffffe | FE_HAS_LOCK ... The error message about FE_SET_VOLTAGE does sometimes appear if i try then/during mplayer /dev/dvb/adapter0/dvr0 I get nothing, dvr does not output any byte Relevant modules loaded are saa7134_alsa 14689 1 tda1004x 17477 1 saa7134_dvb 22221 0 videobuf_dvb 8517 1 saa7134_dvb dst_ca 14913 1 tuner_simple 15953 2 tuner_types 17857 1 tuner_simple tda9887 13509 1 tda8290 15685 0 dst 27593 2 dst_ca dvb_bt8xx 17605 0 dvb_core 68673 5 saa7134_dvb,videobuf_dvb,dst_ca,dst,dvb_bt8xx saa7134 128789 2 saa7134_alsa,saa7134_dvb bt878 12793 2 dst,dvb_bt8xx tuner 26249 0 bttv 152661 2 dvb_bt8xx,bt878 videodev 31425 3 saa7134,tuner,bttv The important passages of dmesg look like bttv: driver version 0.9.17 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 16 (level, low) -> IRQ 16 bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 16, latency: 32, mmio: 0xfdcff000 bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is 1822:0001 bttv0: using: Twinhan DST + clones [card=113,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00f5fffd [init] input: i2c IR (Hauppauge) as /class/input/input8 ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-1/1-001a/ir0 [bt878 #0 [hw]] bttv0: tuner absent bttv0: add subdevice "dvb0" bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI Interrupt 0000:01:0b.1[A] -> GSI 16 (level, low) -> IRQ 16 bt878_probe: card id=[0x11822],[ Twinhan VisionPlus DVB ] has DVB functions. bt878(0): Bt878 (rev 17) at 01:0b.1, irq: 16, latency: 32, memory: 0xfdcfe000 saa7130/34: v4l2 driver version 0.2.14 loaded ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 19 (level, low) -> IRQ 19 saa7134[0]: found at 0000:01:04.0, rev: 1, irq: 19, latency: 32, mmio: 0xfddff000 saa7134[0]: subsystem: 021a:0001, board: Medion 7134 [card=12,insmod option] saa7134[0]: board init: gpio is 0 DVB: registering new adapter (bttv0) tuner' 2-0043: chip found @ 0x86 (saa7134[0]) tda9887 2-0043: creating new instance tda9887 2-0043: tda988[5/6/7] found tuner' 2-0061: chip found @ 0xc2 (saa7134[0]) saa7134[0]: i2c eeprom 00: a0 12 02 00 54 20 08 00 43 43 28 0c 00 52 20 12 saa7134[0]: i2c eeprom 10: 00 87 82 0f ff 20 2a 00 00 50 12 00 00 18 0a 10 saa7134[0]: i2c eeprom 20: 01 00 00 02 02 03 01 00 06 ad 00 10 02 51 00 08 saa7134[0]: i2c eeprom 30: 01 18 48 07 03 00 00 0c d2 00 00 10 00 00 12 3c saa7134[0]: i2c eeprom 40: 60 00 00 c0 82 10 00 00 00 00 01 58 40 1b 02 8d saa7134[0]: i2c eeprom 50: 7d 56 65 3f 00 5b 06 02 00 00 04 00 0c 00 04 00 saa7134[0]: i2c eeprom 60: 2b a6 7d 38 2b d4 d3 5b 3a 51 e5 5e c6 87 f2 ff saa7134[0]: i2c eeprom 70: ff a6 2a 58 3a 5b 13 86 b2 58 1a d4 d3 58 5a 5d saa7134[0]: i2c eeprom 80: 02 22 50 1f 21 8f 80 87 bf 5b fb 5b 3f ad 28 50 saa7134[0]: i2c eeprom 90: 16 7d 28 1c 41 18 48 87 f3 00 01 8d f3 00 01 50 saa7134[0]: i2c eeprom a0: 22 58 12 7f 60 00 91 5e 18 ff ff a6 7d da d8 79 saa7134[0]: i2c eeprom b0: 29 52 96 d4 d3 5b 3a ad 2b 41 84 22 a6 58 66 00 saa7134[0]: i2c eeprom c0: 93 26 29 a6 2a 58 3a 5b 13 a6 29 58 1a 61 2b d4 saa7134[0]: i2c eeprom d0: d3 49 82 8f ba 49 82 8f f2 00 01 5d 12 22 7e 1f saa7134[0]: i2c eeprom e0: 21 8f 80 87 bf 5b fb 5b 3f ad 28 50 16 7d 28 1c saa7134[0]: i2c eeprom f0: 41 18 48 87 f3 00 01 8d f3 00 01 50 22 60 29 7f saa7134[0] Cant determine tuner type 1000 from EEPROM saa7134[0] Tuner type is 63 tuner-simple 2-0061: creating new instance tuner-simple 2-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner) saa7134[0]: Overlay support disabled. saa7134[0]: registered device video0 [v4l2] saa7134[0]: registered device vbi0 saa7134[0]: registered device radio0 dst(0) dst_get_device_id: Recognise [DSTMCI] dst(0) dst_get_device_id: Unsupported dst(0) dst_check_mb86a15: Cmd=[0x10], failed dst(0) dst_get_device_id: Unsupported DST type flags : 0x1 newtuner 0x1000 VLF 0x10 firmware version = 2 dst(0) dst_get_mac: MAC Address=[00:08:ca:11:e6:00] dst(0) dst_get_tuner_info: DST TYpe = MULTI FE dst_ca_attach: registering DST-CA device DVB: registering frontend 0 (DST DVB-S)... tuner-simple 2-0061: attaching existing instance tuner-simple 2-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner) DVB: registering new adapter (saa7134[0]) DVB: registering frontend 1 (Philips TDA10046H DVB-T)... tda1004x: setting up plls for 53MHz sampling clock tda1004x: found firmware revision 26 -- ok saa7134 ALSA driver for DMA sound loaded saa7134[0]/alsa: saa7134[0] at 0xfddff000 irq 19 registered as card -1 ... ... dst_ca_open: Device opened [f21dfa00] dst_ca_ioctl: Getting Slot capabilities put_checksum: Computing string checksum. put_checksum: -> string length : 0x07 put_checksum: -> checksum : 0xb5 dst_put_ci: Put Command i2c IR (Hauppauge): unknown key: key=0x3f raw=0x1fff down=1 dst_ci_command: 8820 not ready dst_put_ci: Put Command dst_ci_command: 8820 not ready dst_put_ci: Put Command dst_ci_command: Write not successful, trying to recover dst_put_ci: Put Command dst_ci_command: Write not successful, trying to recover dst_put_ci: Put Command dst_ci_command: Write not successful, trying to recover ca_get_slot_caps: -->dst_put_ci FAILED ! dst_ca_ioctl: -->CA_GET_CAP Failed ! dst_ca_release: Device closed. i2c IR (Hauppauge): unknown key: key=0x3f raw=0x1fff down=0 dst_ca_open: Device opened [f459ab00] dst_ca_ioctl: Getting Slot capabilities put_checksum: Computing string checksum. put_checksum: -> string length : 0x07 put_checksum: -> checksum : 0xb5 dst_put_ci: Put Command i2c IR (Hauppauge): unknown key: key=0x3f raw=0x1fff down=1 dst_ci_command: Write not successful, trying to recover dst_put_ci: Put Command dst_ci_command: Write not successful, trying to recover dst_put_ci: Put Command dst_ci_command: Write not successful, trying to recover dst_put_ci: Put Command dst_ci_command: Write not successful, trying to recover dst_put_ci: Put Command dst_ci_command: Write not successful, trying to recover ca_get_slot_caps: -->dst_put_ci FAILED ! dst_ca_ioctl: -->CA_GET_CAP Failed ! dst_ca_release: Device closed. [drm] Initialized drm 1.1.0 20060810 PCI: Setting latency timer of device 0000:00:02.0 to 64 [drm] Initialized i915 1.6.0 20060119 on minor 0 ... tda1004x: setting up plls for 53MHz sampling clock tda1004x: found firmware revision 26 -- ok ================================== Can somebody see the real error/misconfiguration ? -- Jetzt 1 Monat kostenlos! GMX FreeDSL - Telefonanschluss + DSL für nur 17,95 Euro/mtl.!* http://dsl.gmx.de/?ac=OM.AD.PD003K11308T4569a -- Psssst! Schon vom neuen GMX MultiMessenger gehört? Der kann`s mit allen: http://www.gmx.net/de/go/multimessenger01 -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
