Hello Peter and Alex,
On 8/8/21 10:41 AM, Alejandro Colomar wrote:
> From: Peter Collingbourne <pcc@xxxxxxxxxx>
>
> Signed-off-by: Peter Collingbourne <pcc@xxxxxxxxxx>
> Signed-off-by: Alejandro Colomar <alx.manpages@xxxxxxxxx>
Thanks for this patch Peter. Applied.
Cheers,
Michael
> ---
> man2/sigaction.2 | 123 +++++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 123 insertions(+)
>
> diff --git a/man2/sigaction.2 b/man2/sigaction.2
> index 57ad6418c..4bf6f095e 100644
> --- a/man2/sigaction.2
> +++ b/man2/sigaction.2
> @@ -261,6 +261,44 @@ This flag is meaningful only when establishing a signal handler.
> .\" .I sa_sigaction
> .\" field was added in Linux 2.1.86.)
> .\"
> +.TP
> +.B SA_UNSUPPORTED
> +Used to dynamically probe for flag bit support.
> +.IP
> +If an attempt to register a handler succeeds with this flag set in
> +.I act->sa_flags
> +alongside other flags that are potentially unsupported by the kernel,
> +and an immediately subsequent
> +.BR sigaction ()
> +call specifying the same signal number n and with non-NULL
> +.I oldact
> +yields
> +.B SA_UNSUPPORTED
> +.I clear
> +in
> +.IR oldact->sa_flags ,
> +then
> +.I oldact->sa_flags
> +may be used as a bitmask
> +describing which of the potentially unsupported flags are,
> +in fact, supported.
> +See the section "Dynamically probing for flag bit support"
> +below for more details.
> +.TP
> +.BR SA_EXPOSE_TAGBITS " (since Linux 5.11)"
> +Normally, when delivering a signal,
> +an architecture-specific set of tag bits are cleared from the
> +.I si_addr
> +field of
> +.IR siginfo_t .
> +If this flag is set,
> +an architecture-specific subset of the tag bits will be preserved in
> +.IR si_addr .
> +.IP
> +Programs that need to be compatible with Linux versions older than 5.11
> +must use
> +.B SA_UNSUPPORTED
> +to probe for support.
> .SS The siginfo_t argument to a SA_SIGINFO handler
> When the
> .B SA_SIGINFO
> @@ -846,6 +884,91 @@ Triggered by a
> .BR seccomp (2)
> filter rule.
> .RE
> +.SS Dynamically probing for flag bit support
> +The
> +.BR sigaction ()
> +call on Linux accepts unknown bits set in
> +.I act->sa_flags
> +without error.
> +The behavior of the kernel starting with Linux 5.11 is that a second
> +.BR sigaction ()
> +will clear unknown bits from
> +.IR oldact->sa_flags .
> +However, historically, a second
> +.BR sigaction ()
> +call would typically leave those bits set in
> +.IR oldact->sa_flags .
> +.PP
> +This means that support for new flags cannot be detected
> +simply by testing for a flag in
> +.IR sa_flags ,
> +and a program must test that
> +.B SA_UNSUPPORTED
> +has been cleared before relying on the contents of
> +.IR sa_flags .
> +.PP
> +Since the behavior of the signal handler cannot be guaranteed
> +unless the check passes,
> +it is wise to either block the affected signal
> +while registering the handler and performing the check in this case,
> +or where this is not possible,
> +for example if the signal is synchronous, to issue the second
> +.BR sigaction ()
> +in the signal handler itself.
> +.PP
> +In kernels that do not support a specific flag,
> +the kernel's behavior is as if the flag was not set,
> +even if the flag was set in
> +.IR act->sa_flags .
> +.PP
> +The flags
> +.BR SA_NOCLDSTOP ,
> +.BR SA_NOCLDWAIT ,
> +.BR SA_SIGINFO ,
> +.BR SA_ONSTACK ,
> +.BR SA_RESTART ,
> +.BR SA_NODEFER ,
> +.BR SA_RESETHAND ,
> +and, if defined by the architecture,
> +.B SA_RESTORER
> +may not be reliably probed for using this mechanism,
> +because they were introduced before Linux 5.11.
> +However, in general, programs may assume that these flags are supported,
> +since they have all been supported since Linux 2.6,
> +which was released in the year 2003.
> +.PP
> +The following example program exits with status 0 if
> +.B SA_EXPOSE_TAGBITS
> +is determined to be supported, and 1 otherwise.
> +.PP
> +.EX
> +#include <signal.h>
> +#include <stdio.h>
> +#include <unistd.h>
> +
> +void handler(int signo, siginfo_t *info, void *context) {
> + struct sigaction oldact;
> + if (sigaction(SIGSEGV, 0, &oldact) == 0 &&
> + !(oldact.sa_flags & SA_UNSUPPORTED) &&
> + (oldact.sa_flags & SA_EXPOSE_TAGBITS)) {
> + _exit(0);
> + } else {
> + _exit(1);
> + }
> +}
> +
> +int main(void) {
> + struct sigaction act = {0};
> + act.sa_flags = SA_SIGINFO | SA_UNSUPPORTED | SA_EXPOSE_TAGBITS;
> + act.sa_sigaction = handler;
> + if (sigaction(SIGSEGV, &act, 0) != 0) {
> + perror("sigaction");
> + return 1;
> + }
> +
> + raise(SIGSEGV);
> +}
> +.EE
> .SH RETURN VALUE
> .BR sigaction ()
> returns 0 on success; on error, \-1 is returned, and
>
--
Michael Kerrisk
Linux man-pages maintainer; http://www.kernel.org/doc/man-pages/
Linux/UNIX System Programming Training: http://man7.org/training/
