Hi Michael, On Sat, Aug 19, 2023 at 1:49 AM Michael Schmitz <schmitzmic@xxxxxxxxx> wrote:
With commit 44b1fbc0f5f3 ("m68k/q40: Replace q40ide driver with pata_falcon and falconide"), the Q40 IDE driver was replaced by pata_falcon.c. Both IO and memory resources were defined for the Q40 IDE platform device, but definition of the IDE register addresses was modeled after the Falcon case, both in use of the memory resources and in including register scale and byte vs. word offset in the address. This was correct for the Falcon case, which does not apply any address translation to the register addresses. In the Q40 case, all of device base address, byte access offset and register scaling is included in the platform specific ISA access translation (in asm/mm_io.h). As a consequence, such address translation gets applied twice, and register addresses are mangled. Use the device base address from the platform IO resource, and use standard register offsets from that base in order to calculate register addresses (the IO address translation will then apply the correct ISA window base and scaling). Encode PIO_OFFSET into IO port addresses for all registers except the data transfer register. Encode the MMIO offset there (pata_falcon_data_xfer() directly uses raw IO with no address translation). Reported-by: William R Sowerbutts <will@xxxxxxxxxxxxxx> Closes: https://lore.kernel.org/r/CAMuHMdUU62jjunJh9cqSqHT87B0H0A4udOOPs=WN7WZKpcagVA@xxxxxxxxxxxxxx Link: https://lore.kernel.org/r/CAMuHMdUU62jjunJh9cqSqHT87B0H0A4udOOPs=WN7WZKpcagVA@xxxxxxxxxxxxxx Fixes: 44b1fbc0f5f3 ("m68k/q40: Replace q40ide driver with pata_falcon and falconide") Cc: stable@xxxxxxxxxxxxxxx Cc: Finn Thain <fthain@xxxxxxxxxxxxxx> Cc: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> Tested-by: William R Sowerbutts <will@xxxxxxxxxxxxxx> Signed-off-by: Michael Schmitz <schmitzmic@xxxxxxxxx>
Thanks for the update!
--- a/drivers/ata/pata_falcon.c +++ b/drivers/ata/pata_falcon.c @@ -165,26 +165,39 @@ static int __init pata_falcon_init_one(struct platform_device *pdev) ap->pio_mask = ATA_PIO4; ap->flags |= ATA_FLAG_SLAVE_POSS | ATA_FLAG_NO_IORDY; - base = (void __iomem *)base_mem_res->start; /* N.B. this assumes data_addr will be used for word-sized I/O only */ - ap->ioaddr.data_addr = base + 0 + 0 * 4; - ap->ioaddr.error_addr = base + 1 + 1 * 4; - ap->ioaddr.feature_addr = base + 1 + 1 * 4; - ap->ioaddr.nsect_addr = base + 1 + 2 * 4; - ap->ioaddr.lbal_addr = base + 1 + 3 * 4; - ap->ioaddr.lbam_addr = base + 1 + 4 * 4; - ap->ioaddr.lbah_addr = base + 1 + 5 * 4; - ap->ioaddr.device_addr = base + 1 + 6 * 4; - ap->ioaddr.status_addr = base + 1 + 7 * 4; - ap->ioaddr.command_addr = base + 1 + 7 * 4; - - base = (void __iomem *)ctl_mem_res->start; - ap->ioaddr.altstatus_addr = base + 1; - ap->ioaddr.ctl_addr = base + 1; - - ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx", - (unsigned long)base_mem_res->start, - (unsigned long)ctl_mem_res->start); + ap->ioaddr.data_addr = (void __iomem *)base_mem_res->start; + + if (base_res) { /* only Q40 has IO resources */ + io_offset = 0x10000; + reg_scale = 1; + base = (void __iomem *)base_res->start; + ctl_base = (void __iomem *)ctl_res->start; + + ata_port_desc(ap, "cmd %pa ctl %pa", + &base_res->start, + &ctl_res->start);
This can be moved outside the else, using %px to format base and ctl_base.
+ } else { + base = (void __iomem *)base_mem_res->start; + ctl_base = (void __iomem *)ctl_mem_res->start; + + ata_port_desc(ap, "cmd %pa ctl %pa", + &base_mem_res->start, + &ctl_mem_res->start); + }
Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds