Hi Geert, On 2/11/20 9:39 PM, Geert Uytterhoeven wrote:
Hi Andreas, On Sun, Nov 1, 2020 at 1:47 PM Andreas Schwab <schwab@xxxxxxxxxxxxxx> wrote:On Nov 01 2020, Sam Ravnborg wrote:On Sun, Nov 01, 2020 at 11:29:41AM +0100, Geert Uytterhoeven wrote:The horizontal resolution (640) for the TT High video mode (1280x960) is definitely bogus. While fixing that, correct the timings to match the TTM195 service manual. Signed-off-by: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> --- Untested on actual hardware, hence the RFC. v2: - Use correct base. --- drivers/video/fbdev/atafb.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/video/fbdev/atafb.c b/drivers/video/fbdev/atafb.c index f253daa05d9d3872..5ecf3ec9f94cb720 100644 --- a/drivers/video/fbdev/atafb.c +++ b/drivers/video/fbdev/atafb.c @@ -495,8 +495,8 @@ static struct fb_videomode atafb_modedb[] __initdata = { "tt-mid", 60, 640, 480, 31041, 120, 100, 8, 16, 140, 30, 0, FB_VMODE_NONINTERLACED | FB_VMODE_YWRAP }, { - /* 1280x960, 29 kHz, 60 Hz (TT high) */ - "tt-high", 57, 640, 960, 31041, 120, 100, 8, 16, 140, 30, + /* 1280x960, 72 kHz, 72 Hz (TT high) */ + "tt-high", 57, 1280, 960, 7761, 260, 60, 36, 4, 192, 4, 0, FB_VMODE_NONINTERLACED | FB_VMODE_YWRAPWell-spotted. The change of 640 => 1280 is surely right.TBH, I spotted that 7 years ago, but never got to looking up and calculating the other values...
Looks like one of my copy&paste errors that went undetected for too long... I seem to have copied the tt-mid values above in that case. Need to go back to the old driver to see what had been used there. A quick diff didn't show anything useful.
I have a harder time understanding why the change of pixclock from 31041 to 7761 is correct. All other modes have a pixclock close to or equal to 32000 - so it looks strange this one is off.32000 ps is 31.25 MHz. Looks like these are bogus, too, and only the VGA and Falcon video modes are correct?
These were the only ones I could test (haven't seen a TT in 20 years). At the time I worked on the Atari FB driver, I didn't have access to the Profibuch either.
As Andreas mentioned, the Falcon (or external) hardware is the only one that can be programmed freely, so we need to work from the 95 MHz pixclock Andreas found. That's 10.5 ns approx.
10.5 ns * 1280 * 960 (omitting HBL and VBL timing) gives 77 Hz refresh so I don't think 95 MHz for 72 Hz refresh are unreasonable.
Need to look up what all the other numbers in the mode entry mean now ... Cheers, Michael
According to the Profibuch the pixclock should be about 95000.95 ns? That's a 10.5 MHz pixel clock? Definitely too low. The TTM195 manual says 128.85 MHz. Gr{oetje,eeting}s, Geert
