The LIMIT_TRANSFERSIZE, PSEUDO_DMA, PARITY and UNSAFE options are all documented in the core drivers where they are used. The same goes for the chip databook reference. Remove the duplicate comments. Signed-off-by: Finn Thain <fthain@xxxxxxxxxxxxxxxxxxx> --- drivers/scsi/dtc.c | 17 +---------------- drivers/scsi/dtc.h | 16 ---------------- drivers/scsi/g_NCR5380.c | 16 ---------------- drivers/scsi/g_NCR5380.h | 12 ------------ drivers/scsi/mac_scsi.c | 12 ------------ drivers/scsi/mac_scsi.h | 12 ------------ drivers/scsi/pas16.c | 31 ------------------------------- drivers/scsi/pas16.h | 12 ------------ drivers/scsi/sun3_scsi.c | 21 --------------------- drivers/scsi/sun3_scsi.h | 12 ------------ drivers/scsi/t128.c | 23 ----------------------- drivers/scsi/t128.h | 12 ------------ 12 files changed, 1 insertion(+), 195 deletions(-) Index: linux/drivers/scsi/dtc.c =================================================================== --- linux.orig/drivers/scsi/dtc.c 2014-10-02 16:55:58.000000000 +1000 +++ linux/drivers/scsi/dtc.c 2014-10-02 16:56:00.000000000 +1000 @@ -19,24 +19,9 @@ * +1 (303) 440-4894 * * DISTRIBUTION RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook -*/ + */ /* - * Options : - * PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance - * increase compared to polled I/O. - * - * PARITY - enable parity checking. Not supported. - * - * UNSAFE - leave interrupts enabled during pseudo-DMA transfers. - * You probably want this. - * * The card is detected and initialized in one of several ways : * 1. Autoprobe (default) - since the board is memory mapped, * a BIOS signature is scanned for to locate the registers. Index: linux/drivers/scsi/g_NCR5380.c =================================================================== --- linux.orig/drivers/scsi/g_NCR5380.c 2014-10-02 16:55:58.000000000 +1000 +++ linux/drivers/scsi/g_NCR5380.c 2014-10-02 16:56:00.000000000 +1000 @@ -20,18 +20,6 @@ * Thomas Sailer, sailer@xxxxxxxxxxxxxx * * ALPHA RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ /* @@ -40,10 +28,6 @@ */ /* - * Options : - * - * PARITY - enable parity checking. Not supported. - * * The card is detected and initialized in one of several ways : * 1. With command line overrides - NCR5380=port,irq may be * used on the LILO command line to override the defaults. Index: linux/drivers/scsi/pas16.c =================================================================== --- linux.orig/drivers/scsi/pas16.c 2014-10-02 16:55:58.000000000 +1000 +++ linux/drivers/scsi/pas16.c 2014-10-02 16:56:00.000000000 +1000 @@ -22,40 +22,9 @@ * Media Vision * (510) 770-8600 * (800) 348-7116 - * - * and - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ /* - * Options : - * LIMIT_TRANSFERSIZE - if defined, limit the pseudo-dma transfers to 512 - * bytes at a time. Since interrupts are disabled by default during - * these transfers, we might need this to give reasonable interrupt - * service time if the transfer size gets too large. - * - * PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance - * increase compared to polled I/O. - * - * PARITY - enable parity checking. Not supported. - * - * UNSAFE - leave interrupts enabled during pseudo-DMA transfers. This - * parameter comes from the NCR5380 code. It is NOT unsafe with - * the PAS16 and you should use it. If you don't you will have - * a problem with dropped characters during high speed - * communications during SCSI transfers. If you really don't - * want to use UNSAFE you can try defining LIMIT_TRANSFERSIZE or - * twiddle with the transfer size in the high level code. - * * The card is detected and initialized in one of several ways : * 1. Autoprobe (default) - There are many different models of * the Pro Audio Spectrum/Studio 16, and I only have one of Index: linux/drivers/scsi/sun3_scsi.c =================================================================== --- linux.orig/drivers/scsi/sun3_scsi.c 2014-10-02 16:55:58.000000000 +1000 +++ linux/drivers/scsi/sun3_scsi.c 2014-10-02 16:56:00.000000000 +1000 @@ -22,27 +22,6 @@ * Copyright 1995, Russell King * * ALPHA RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 - */ - - -/* - * This is from mac_scsi.h, but hey, maybe this is useful for Sun3 too! :) - * - * Options : - * - * PARITY - enable parity checking. Not supported. */ #include <linux/types.h> Index: linux/drivers/scsi/t128.c =================================================================== --- linux.orig/drivers/scsi/t128.c 2014-10-02 16:55:58.000000000 +1000 +++ linux/drivers/scsi/t128.c 2014-10-02 16:56:00.000000000 +1000 @@ -23,32 +23,9 @@ * 5415 Randall Place * Fremont, CA 94538 * 1+ (415) 770-1400, FAX 1+ (415) 770-9910 - * - * and - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ /* - * Options : - * PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance - * increase compared to polled I/O. - * - * PARITY - enable parity checking. Not supported. - * - * UNSAFE - leave interrupts enabled during pseudo-DMA transfers. You - * only really want to use this if you're having a problem with - * dropped characters during high speed communications, and even - * then, you're going to be better off twiddling with transfersize. - * * The card is detected and initialized in one of several ways : * 1. Autoprobe (default) - since the board is memory mapped, * a BIOS signature is scanned for to locate the registers. Index: linux/drivers/scsi/dtc.h =================================================================== --- linux.orig/drivers/scsi/dtc.h 2014-10-02 16:55:53.000000000 +1000 +++ linux/drivers/scsi/dtc.h 2014-10-02 16:56:00.000000000 +1000 @@ -7,22 +7,6 @@ * +1 (303) 440-4894 * * DISTRIBUTION RELEASE 2. - * - * For more information, please consult - * - * - * - * and - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ #ifndef DTC3280_H Index: linux/drivers/scsi/g_NCR5380.h =================================================================== --- linux.orig/drivers/scsi/g_NCR5380.h 2014-10-02 16:55:53.000000000 +1000 +++ linux/drivers/scsi/g_NCR5380.h 2014-10-02 16:56:00.000000000 +1000 @@ -11,18 +11,6 @@ * K.Lentin@xxxxxxxxxxxxxxxx * * ALPHA RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ #ifndef GENERIC_NCR5380_H Index: linux/drivers/scsi/mac_scsi.c =================================================================== --- linux.orig/drivers/scsi/mac_scsi.c 2014-10-02 16:55:58.000000000 +1000 +++ linux/drivers/scsi/mac_scsi.c 2014-10-02 16:56:00.000000000 +1000 @@ -11,18 +11,6 @@ * Copyright 1995, Russell King * * ALPHA RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ #include <linux/types.h> Index: linux/drivers/scsi/mac_scsi.h =================================================================== --- linux.orig/drivers/scsi/mac_scsi.h 2014-10-02 16:55:50.000000000 +1000 +++ linux/drivers/scsi/mac_scsi.h 2014-10-02 16:56:00.000000000 +1000 @@ -8,18 +8,6 @@ * +1 (303) 440-4894 * * ALPHA RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ #ifndef MAC_NCR5380_H Index: linux/drivers/scsi/pas16.h =================================================================== --- linux.orig/drivers/scsi/pas16.h 2014-10-02 16:55:53.000000000 +1000 +++ linux/drivers/scsi/pas16.h 2014-10-02 16:56:00.000000000 +1000 @@ -18,18 +18,6 @@ * Media Vision * (510) 770-8600 * (800) 348-7116 - * - * and - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ Index: linux/drivers/scsi/sun3_scsi.h =================================================================== --- linux.orig/drivers/scsi/sun3_scsi.h 2014-10-02 16:55:53.000000000 +1000 +++ linux/drivers/scsi/sun3_scsi.h 2014-10-02 16:56:00.000000000 +1000 @@ -15,18 +15,6 @@ * +1 (303) 440-4894 * * ALPHA RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ #ifndef SUN3_SCSI_H Index: linux/drivers/scsi/t128.h =================================================================== --- linux.orig/drivers/scsi/t128.h 2014-10-02 16:55:53.000000000 +1000 +++ linux/drivers/scsi/t128.h 2014-10-02 16:56:00.000000000 +1000 @@ -20,18 +20,6 @@ * 5415 Randall Place * Fremont, CA 94538 * 1+ (415) 770-1400, FAX 1+ (415) 770-9910 - * - * and - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ #ifndef T128_H -- To unsubscribe from this list: send the line "unsubscribe linux-m68k" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
