From: Greg Ungerer <gerg@xxxxxxxxxxx> There is a bunch of old unused and ugly register definitions in the ColdFire 5282 header. Remove them. Signed-off-by: Greg Ungerer <gerg@xxxxxxxxxxx> --- arch/m68k/include/asm/m528xsim.h | 51 +------------------------------------- 1 files changed, 1 insertions(+), 50 deletions(-) diff --git a/arch/m68k/include/asm/m528xsim.h b/arch/m68k/include/asm/m528xsim.h index 4acb3c0..cf68ca0 100644 --- a/arch/m68k/include/asm/m528xsim.h +++ b/arch/m68k/include/asm/m528xsim.h @@ -233,23 +233,6 @@ #define MCFGPIO_IRQ_VECBASE MCFINT_VECBASE #define MCFGPIO_PIN_MAX 180 - -/* - * Derek Cheung - 6 Feb 2005 - * add I2C and QSPI register definition using Freescale's MCF5282 - */ -/* set Port AS pin for I2C or UART */ -#define MCF5282_GPIO_PASPAR (volatile u16 *) (MCF_IPSBAR + 0x00100056) - -/* Port UA Pin Assignment Register (8 Bit) */ -#define MCF5282_GPIO_PUAPAR 0x10005C - -/* Interrupt Mask Register Register Low */ -#define MCF5282_INTC0_IMRL (volatile u32 *) (MCF_IPSBAR + 0x0C0C) -/* Interrupt Control Register 7 */ -#define MCF5282_INTC0_ICR17 (volatile u8 *) (MCF_IPSBAR + 0x0C51) - - /* * Reset Control Unit (relative to IPSBAR). */ @@ -259,37 +242,5 @@ #define MCF_RCR_SWRESET 0x80 /* Software reset bit */ #define MCF_RCR_FRCSTOUT 0x40 /* Force external reset */ -/********************************************************************* -* -* Inter-IC (I2C) Module -* -*********************************************************************/ -/* Read/Write access macros for general use */ -#define MCF5282_I2C_I2ADR (volatile u8 *) (MCF_IPSBAR + 0x0300) // Address -#define MCF5282_I2C_I2FDR (volatile u8 *) (MCF_IPSBAR + 0x0304) // Freq Divider -#define MCF5282_I2C_I2CR (volatile u8 *) (MCF_IPSBAR + 0x0308) // Control -#define MCF5282_I2C_I2SR (volatile u8 *) (MCF_IPSBAR + 0x030C) // Status -#define MCF5282_I2C_I2DR (volatile u8 *) (MCF_IPSBAR + 0x0310) // Data I/O - -/* Bit level definitions and macros */ -#define MCF5282_I2C_I2ADR_ADDR(x) (((x)&0x7F)<<0x01) - -#define MCF5282_I2C_I2FDR_IC(x) (((x)&0x3F)) - -#define MCF5282_I2C_I2CR_IEN (0x80) // I2C enable -#define MCF5282_I2C_I2CR_IIEN (0x40) // interrupt enable -#define MCF5282_I2C_I2CR_MSTA (0x20) // master/slave mode -#define MCF5282_I2C_I2CR_MTX (0x10) // transmit/receive mode -#define MCF5282_I2C_I2CR_TXAK (0x08) // transmit acknowledge enable -#define MCF5282_I2C_I2CR_RSTA (0x04) // repeat start - -#define MCF5282_I2C_I2SR_ICF (0x80) // data transfer bit -#define MCF5282_I2C_I2SR_IAAS (0x40) // I2C addressed as a slave -#define MCF5282_I2C_I2SR_IBB (0x20) // I2C bus busy -#define MCF5282_I2C_I2SR_IAL (0x10) // aribitration lost -#define MCF5282_I2C_I2SR_SRW (0x04) // slave read/write -#define MCF5282_I2C_I2SR_IIF (0x02) // I2C interrupt -#define MCF5282_I2C_I2SR_RXAK (0x01) // received acknowledge - - +/****************************************************************************/ #endif /* m528xsim_h */ -- 1.7.0.4 -- To unsubscribe from this list: send the line "unsubscribe linux-m68k" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
