Signed-off-by: Paul Bolle <pebolle@xxxxxxxxxx> --- arch/m68k/Kconfig | 28 +--------------------------- arch/m68k/Kconfig.nommu | 44 -------------------------------------------- 2 files changed, 1 insertions(+), 71 deletions(-) diff --git a/arch/m68k/Kconfig b/arch/m68k/Kconfig index 9e8ee9d..58c6496 100644 --- a/arch/m68k/Kconfig +++ b/arch/m68k/Kconfig @@ -149,32 +149,6 @@ config MULTIFACE_III_TTY To compile this driver as a module, choose M here. -config GVPIOEXT - tristate "GVP IO-Extender support" - depends on PARPORT=n && ZORRO - help - If you want to use a GVP IO-Extender serial card in Linux, say Y. - Otherwise, say N. - -config GVPIOEXT_LP - tristate "GVP IO-Extender parallel printer support" - depends on GVPIOEXT - help - Say Y to enable driving a printer from the parallel port on your - GVP IO-Extender card, N otherwise. - -config GVPIOEXT_PLIP - tristate "GVP IO-Extender PLIP support" - depends on GVPIOEXT - help - Say Y to enable doing IP over the parallel port on your GVP - IO-Extender card, N otherwise. - -config MAC_HID - bool - depends on INPUT_ADBHID - default y - config HPDCA tristate "HP DCA serial support" depends on DIO && SERIAL_8250 @@ -217,7 +191,7 @@ config DN_SERIAL config SERIAL_CONSOLE bool "Support for serial port console" - depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL) + depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL) ---help--- If you say Y here, it will be possible to use a serial port as the system console (the system console is the device which receives all diff --git a/arch/m68k/Kconfig.nommu b/arch/m68k/Kconfig.nommu index ff46383..2b7f1e9 100644 --- a/arch/m68k/Kconfig.nommu +++ b/arch/m68k/Kconfig.nommu @@ -542,13 +542,6 @@ config SAVANTrosie1 help Support for the Savant Rosie1 board. -config ROMFS_FROM_ROM - bool "ROMFS image not RAM resident" - depends on (NETtel || SNAPGEAR) - help - The ROMfs filesystem will stay resident in the FLASH/ROM, not be - moved into RAM. - config PILOT bool default y @@ -564,21 +557,11 @@ config FREESCALE default y depends on (M5206eC3 || M5208EVB || M5235EVB || M5249C3 || M5271EVB || M5272C3 || M5275EVB || M5282EVB || M5307C3 || M5329EVB || M5407C3) -config HW_FEITH - bool - default y - depends on (CLEOPATRA || CANCam || SCALES) - config senTec bool default y depends on (COBRA5272 || COBRA5282) -config EMAC_INC - bool - default y - depends on (SOM5282EM) - config SNEHA bool default y @@ -673,33 +656,6 @@ config KERNELBASE a system with the RAM based at address 0, and leaving enough room for the theoretical maximum number of 256 vectors. -choice - prompt "RAM bus width" - default RAMAUTOBIT - -config RAMAUTOBIT - bool "AUTO" - help - Select the physical RAM data bus size. Not needed on most platforms, - so you can generally choose AUTO. - -config RAM8BIT - bool "8bit" - help - Configure RAM bus to be 8 bits wide. - -config RAM16BIT - bool "16bit" - help - Configure RAM bus to be 16 bits wide. - -config RAM32BIT - bool "32bit" - help - Configure RAM bus to be 32 bits wide. - -endchoice - comment "ROM configuration" config ROM -- 1.7.4.4 -- To unsubscribe from this list: send the line "unsubscribe linux-m68k" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
