On Tue, 11 Nov 2008, Geert Uytterhoeven wrote:
On Mon, 10 Nov 2008, Finn Thain wrote:
On Sun, 9 Nov 2008, Geert Uytterhoeven wrote:
On Mon, 3 Nov 2008, Finn Thain wrote:
I agree with Geert. Ignore my comment about device_initcall -- I
was looking at via-cuda.c but that is not a good example.
drivers/scsi/mac_esp.c is a better example.
esp_mac_probe checks the macintosh_config entry. That and
esp_mac_remove are the platform device entry points Geert referred
to. The module entry points are mac_esp_init and mac_esp_exit. I
think you could use either of the platform device probe routine or
the module init routine to set the base address.
Ideally, the _probe() routine should not look at the bits in
macintosh_config, but only at the platform device and its resources.
Makes sense.
The creation of the platform device should be moved to
arch/m68k/mac/config
That means adding #if CONFIG_BLK_DEV_SWIM to config.c.
No, its creation code should not depend on any config option (except
CONFIG_MAC :-). This means the platform device will always be created
when the physical hardware is present.
So we create a global platform device pointer for every possible mac
device regardless of whether they're enabled in Kconfig or not?
(Not that I'm not going to complain about a few bytes if the benefit
outweighs the disadvantages. I'm just trying to understand both.)
It also makes drivers/block/swim.c less cohesive.
When the device framework was introduced, platform devices and platform
drivers were handled in the driver (source file) itself. Later it was
realized this was actually a mistake, and the platform devices and
platform drivers were separated.
I've heard that "mistake" mentioned before, but I've never heard an
explanation (i.e. why this might be a problem for say, macmace, mac_sonic
or mac_esp -- or swim).
which would create the platform device, and only if the bits in
macintosh_config indicate that the hardware is present. The actual
value of swim_base can be stored in a struct resource linked to the
platform device.
I'm probably missing something here, but I can see some benefit in
doing this only in the absence of a global macintosh_config.
But if you didn't have a global macintosh_config, several parts of
macintosh_config (especially macintosh_config->ident) would end up
duplicated in each of the struct resources for the platform devices,
no?
You need some logic to device whether to create a platform device or
not. On Mac, the logical way is to look in the macintosh_config table.
Well, I can some the benefit as long as that logic doesn't leak out of
config.c, as it does now.
On Amiga, you would use
if (AMIGAHW_PRESENT(AMI_XXX))
platform_device_register{,_simple}(...);
Converting the existing Amiga drivers is somewhere on my todo-list
(since a just way too long time)...
I guess there must be an example somewhere I can look at to try to
understand this?
Would you explain it is we gain from moving platform init routines
into config.c? I can only see disadvantages.
The device framework is the recommended way to handle devices and
drivers across all Linux platforms.
All existing platform devices show up under /sys/devices/platform/.
Based on this information, the device entry in /dev can be created
automatically, and the corresponding platform driver loadable kernel
modules can be loaded automatically.
E.g. you no longer have to specify in /etc/modules.conf which floppy driver
to load. Currently you have to choose one of:
alias block-major-2 amiflop
alias block-major-2 ataflop
alias block-major-2 swim3
Fair enough, but doesn't the patch you objected to already do that?
Finn
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
--
To unsubscribe from this list: send the line "unsubscribe linux-m68k" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html