On Sat, 01 Feb 2025, Manuel Fombuena wrote:
> Minor edits regarding use of spacing and proofreading.
>
> Signed-off-by: Manuel Fombuena <fombuena@xxxxxxxxxxx>
> ---
> drivers/leds/leds-st1202.c | 48 +++++++++++++++++++-------------------
> 1 file changed, 24 insertions(+), 24 deletions(-)
>
> diff --git a/drivers/leds/leds-st1202.c b/drivers/leds/leds-st1202.c
> index 927874f20839..cb4797ea8f3a 100644
> --- a/drivers/leds/leds-st1202.c
> +++ b/drivers/leds/leds-st1202.c
> @@ -16,27 +16,27 @@
> #include <linux/slab.h>
> #include <linux/string.h>
>
> -#define ST1202_CHAN_DISABLE_ALL 0x00
> -#define ST1202_CHAN_ENABLE_HIGH 0x03
> -#define ST1202_CHAN_ENABLE_LOW 0x02
> -#define ST1202_CONFIG_REG 0x04
> +#define ST1202_CHAN_DISABLE_ALL 0x00
> +#define ST1202_CHAN_ENABLE_HIGH 0x03
> +#define ST1202_CHAN_ENABLE_LOW 0x02
> +#define ST1202_CONFIG_REG 0x04
> /* PATS: Pattern sequence feature enable */
> -#define ST1202_CONFIG_REG_PATS BIT(7)
> +#define ST1202_CONFIG_REG_PATS BIT(7)
> /* PATSR: Pattern sequence runs (self-clear when sequence is finished) */
> -#define ST1202_CONFIG_REG_PATSR BIT(6)
> -#define ST1202_CONFIG_REG_SHFT BIT(3)
> -#define ST1202_DEV_ENABLE 0x01
> -#define ST1202_DEV_ENABLE_ON BIT(0)
> -#define ST1202_DEV_ENABLE_RESET BIT(7)
> -#define ST1202_DEVICE_ID 0x00
> -#define ST1202_ILED_REG0 0x09
> -#define ST1202_MAX_LEDS 12
> -#define ST1202_MAX_PATTERNS 8
> -#define ST1202_MILLIS_PATTERN_DUR_MAX 5660
> -#define ST1202_MILLIS_PATTERN_DUR_MIN 22
> -#define ST1202_PATTERN_DUR 0x16
> -#define ST1202_PATTERN_PWM 0x1E
> -#define ST1202_PATTERN_REP 0x15
> +#define ST1202_CONFIG_REG_PATSR BIT(6)
> +#define ST1202_CONFIG_REG_SHFT BIT(3)
> +#define ST1202_DEV_ENABLE 0x01
> +#define ST1202_DEV_ENABLE_ON BIT(0)
> +#define ST1202_DEV_ENABLE_RESET BIT(7)
> +#define ST1202_DEVICE_ID 0x00
> +#define ST1202_ILED_REG0 0x09
> +#define ST1202_MAX_LEDS 12
> +#define ST1202_MAX_PATTERNS 8
> +#define ST1202_MILLIS_PATTERN_DUR_MAX 5660
> +#define ST1202_MILLIS_PATTERN_DUR_MIN 22
> +#define ST1202_PATTERN_DUR 0x16
> +#define ST1202_PATTERN_PWM 0x1E
> +#define ST1202_PATTERN_REP 0x15
Why are you making this change?
The spacings went from being okay to too large.
> struct st1202_led {
> struct fwnode_handle *fwnode;
> @@ -99,9 +99,9 @@ static int st1202_pwm_pattern_write(struct st1202_chip *chip, int led_num,
> value_h = (u8)(value >> 8);
>
> /*
> - * Datasheet: Register address low = 1Eh + 2*(xh) + 18h*(yh),
> - * where x is the channel number (led number) in hexadecimal (x = 00h .. 0Bh)
> - * and y is the pattern number in hexadecimal (y = 00h .. 07h)
> + * Datasheet: Register address low = 1Eh + 2*(xh) + 18h*(yh),
> + * where x is the channel number (led number) in hexadecimal (x = 00h .. 0Bh)
> + * and y is the pattern number in hexadecimal (y = 00h .. 07h)
> */
> ret = st1202_write_reg(chip, (ST1202_PATTERN_PWM + (led_num * 2) + 0x18 * pattern),
> value_l);
> @@ -288,8 +288,8 @@ static int st1202_setup(struct st1202_chip *chip)
> guard(mutex)(&chip->lock);
>
> /*
> - * Once the supply voltage is applied, the LED1202 executes some internal checks,
> - * afterwords it stops the oscillator and puts the internal LDO in quiescent mode.
> + * Once the supply voltage is applied, the LED1202 executes some internal checks.
> + * Afterwards, it stops the oscillator and puts the internal LDO in quiescent mode.
> * To start the device, EN bit must be set inside the “Device Enable” register at
> * address 01h. As soon as EN is set, the LED1202 loads the adjustment parameters
> * from the internal non-volatile memory and performs an auto-calibration procedure
> --
> 2.48.1
>
--
Lee Jones [李琼斯]
