On Thu, 20 Apr 2023, Naresh Solanki wrote:
> From: Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx>
>
> max597x is hot swap controller with indicator LED support.
> This driver uses DT property to configure led during boot time &
> also provide the LED control in sysfs.
>
> DTS example:
> i2c {
> #address-cells = <1>;
> #size-cells = <0>;
> regulator@3a {
> compatible = "maxim,max5978";
> reg = <0x3a>;
> vss1-supply = <&p3v3>;
>
> regulators {
> sw0_ref_0: sw0 {
> shunt-resistor-micro-ohms = <12000>;
> };
> };
> };
>
> leds {
> #address-cells = <1>;
> #size-cells = <0>;
> led@0 {
> reg = <0>;
> label = "ssd0:green";
> default-state = "on";
> };
> led@1 {
> reg = <1>;
> label = "ssd1:green";
> default-state = "on";
> };
> };
> };
>
> Signed-off-by: Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx>
> Signed-off-by: Naresh Solanki <Naresh.Solanki@xxxxxxxxxxxxx>
> ...
> Change in V6:
> - Improve error handling in case of failure in LED setup
> Changes in V5:
> - Update commit message
> - Fix comments
> - Add necessary new line
> Changes in V4:
> - Remove unwanted preinitialise
> - Remove unneeded line breaks
> - Fix variable name to avoid confusion
> - Update module description to mention LED driver.
> Changes in V3:
> - Remove of_node_put as its handled by for loop
> - Print error if an LED fails to register.
> - Update driver name in Kconfig description
> - Remove unneeded variable assignment
> - Use devm_led_classdev_register to reget led
> Changes in V2:
> - Fix regmap update
> - Remove devm_kfree
> - Remove default-state
> - Add example dts in commit message
> - Fix whitespace in Kconfig
> - Fix comment
> ---
> drivers/leds/Kconfig | 11 +++
> drivers/leds/Makefile | 1 +
> drivers/leds/leds-max597x.c | 133 ++++++++++++++++++++++++++++++++++++
> 3 files changed, 145 insertions(+)
> create mode 100644 drivers/leds/leds-max597x.c
>
> diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
> index 9dbce09eabac..60004cb8c257 100644
> --- a/drivers/leds/Kconfig
> +++ b/drivers/leds/Kconfig
> @@ -590,6 +590,17 @@ config LEDS_ADP5520
> To compile this driver as a module, choose M here: the module will
> be called leds-adp5520.
>
> +config LEDS_MAX597X
> + tristate "LED Support for Maxim 597x"
> + depends on LEDS_CLASS
> + depends on MFD_MAX597X
> + help
> + This option enables support for the Maxim MAX5970 & MAX5978 smart
> + switch indication LEDs via the I2C bus.
> +
> + To compile this driver as a module, choose M here: the module will
> + be called leds-max597x.
> +
> config LEDS_MC13783
> tristate "LED Support for MC13XXX PMIC"
> depends on LEDS_CLASS
> diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
> index d30395d11fd8..da1192e40268 100644
> --- a/drivers/leds/Makefile
> +++ b/drivers/leds/Makefile
> @@ -53,6 +53,7 @@ obj-$(CONFIG_LEDS_LP8501) += leds-lp8501.o
> obj-$(CONFIG_LEDS_LP8788) += leds-lp8788.o
> obj-$(CONFIG_LEDS_LP8860) += leds-lp8860.o
> obj-$(CONFIG_LEDS_LT3593) += leds-lt3593.o
> +obj-$(CONFIG_LEDS_MAX597X) += leds-max597x.o
> obj-$(CONFIG_LEDS_MAX77650) += leds-max77650.o
> obj-$(CONFIG_LEDS_MAX8997) += leds-max8997.o
> obj-$(CONFIG_LEDS_MC13783) += leds-mc13783.o
> diff --git a/drivers/leds/leds-max597x.c b/drivers/leds/leds-max597x.c
> new file mode 100644
> index 000000000000..8ba710d20bff
> --- /dev/null
> +++ b/drivers/leds/leds-max597x.c
> @@ -0,0 +1,133 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Device driver for leds in MAX5970 and MAX5978 IC
> + *
> + * Copyright (c) 2022 9elements GmbH
> + *
> + * Author: Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx>
> + */
> +
> +#include <linux/leds.h>
> +#include <linux/mfd/max597x.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#define ldev_to_maxled(c) container_of(c, struct max597x_led, cdev)
> +
> +struct max597x_led {
> + struct device *dev;
This is already in cdev, no?
> + struct regmap *regmap;
> + struct led_classdev cdev;
> + unsigned int index;
> +};
> +
> +static int max597x_led_set_brightness(struct led_classdev *cdev,
> + enum led_brightness brightness)
> +{
> + struct max597x_led *ddata = ldev_to_maxled(cdev);
> + int ret, val;
> +
> + if (!ddata->regmap)
> + return -ENODEV;
> +
> + /* Set/clear corresponding bit for given led index */
> + val = !brightness ? BIT(ddata->index) : 0;
> +
> + ret = regmap_update_bits(ddata->regmap, MAX5970_REG_LED_FLASH, BIT(ddata->index), val);
> + if (ret < 0)
> + dev_err(cdev->dev, "failed to set brightness %d", ret);
> +
> + return ret;
> +}
> +
> +static int max597x_setup_led(struct max597x_led *ddata, struct regmap *regmap,
> + struct device_node *nc, u32 reg)
> +{
> + int ret;
> +
> + if (of_property_read_string(nc, "label", &ddata->cdev.name))
> + ddata->cdev.name = nc->name;
> +
> + ddata->cdev.max_brightness = 1;
> + ddata->cdev.brightness_set_blocking = max597x_led_set_brightness;
> + ddata->cdev.default_trigger = "none";
> +
> + ret = devm_led_classdev_register(ddata->dev, &ddata->cdev);
Pass the pointer to 'dev' as a param instead.
> + if (ret)
> + dev_err(ddata->dev, "Error initializing LED %s", ddata->cdev.name);
> +
> + return ret;
> +}
> +
> +static int max597x_led_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct device_node *np = dev_of_node(dev->parent);
> + struct regmap *regmap;
> + struct device_node *led_node;
> + struct device_node *child;
> + struct max597x_led *ddata[MAX597X_NUM_LEDS];
> + int ret = 0, i = 0;
> + bool leds_found = false;
> +
> + regmap = dev_get_regmap(pdev->dev.parent, NULL);
> + if (!regmap)
> + return -EPROBE_DEFER;
> +
> + led_node = of_get_child_by_name(np, "leds");
> + if (!led_node)
> + return -ENODEV;
> +
> + for_each_available_child_of_node(led_node, child) {
> + u32 reg;
> +
> + if (of_property_read_u32(child, "reg", ®))
> + continue;
> +
> + if (reg >= MAX597X_NUM_LEDS) {
> + dev_err(dev, "invalid LED (%u >= %d)\n", reg, MAX597X_NUM_LEDS);
> + continue;
> + }
> +
> + ddata[i] = devm_kzalloc(dev, sizeof(struct max597x_led), GFP_KERNEL);
> + if (!ddata[i]) {
> + ret = -ENOMEM;
> + goto exit;
> + }
> +
> + ddata[i]->index = reg;
> + ddata[i]->regmap = regmap;
> + ddata[i]->dev = dev;
> +
> + ret = max597x_setup_led(ddata[i], regmap, child, reg);
> + if (ret < 0) {
> + dev_err(dev, "Failed to initialize LED %u\n", reg);
> + goto exit;
> + }
> + i++;
> + leds_found = true;
You don't need both of these.
Swap them out for something like num_leds_found.
> + }
> +
> + if (!leds_found)
> + return -ENODEV;
Initialise ret to -ENODEV when you declare it, then you can drop this.
> +exit:
> + if (ret < 0)
> + for (int j = 0; j < i; j++)
> + devm_led_classdev_unregister(dev, &ddata[j]->cdev);
Place this section below the return, then you can omit the check.
> + return ret;
> +}
> +
> +static struct platform_driver max597x_led_driver = {
> + .driver = {
> + .name = "max597x-led",
> + },
> + .probe = max597x_led_probe,
> +};
> +
> +module_platform_driver(max597x_led_driver);
> +MODULE_AUTHOR("Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("MAX5970_hot-swap controller LED driver");
> +MODULE_LICENSE("GPL");
>
> base-commit: 9d8d0d98885abba451d7ffc4885236d14ead3c9a
> --
> 2.39.1
>
--
Lee Jones [李琼斯]
