On Fri, Jul 15, 2022 at 1:29 PM ChiaEn Wu <peterwu.pub@xxxxxxxxx> wrote:
>
> From: ChiYuan Huang <cy_huang@xxxxxxxxxxx>
>
> The MediaTek MT6370 is a highly-integrated smart power management IC,
> which includes a single cell Li-Ion/Li-Polymer switching battery
> charger, a USB Type-C & Power Delivery (PD) controller, dual
> Flash LED current sources, a RGB LED driver, a backlight WLED driver,
> a display bias driver and a general LDO for portable devices.
>
> In MediaTek MT6370, there are four channel current-sink RGB LEDs that
> support hardware pattern for constant current, PWM, and breath mode.
> Isink4 channel can also be used as a CHG_VIN power good indicator.
...
> + This driver can also be built as a module. If so the module
so, the
> + will be called "leds-mt6370.ko".
No ".ko".
Why did you ignore these comments? Please go and fix _everywhere_ in
your series.
It's basically the rule of thumb, if the reviewer gives a comment
against an occurrence of something, go through entire series and check
if there are other places like commented one and address them all.
...
> + * Author: Alice Chen <alice_chen@xxxxxxxxxxx>
Strange, the commit message doesn't have a corresponding SoB, why?
...
> +#define MT6370_PWM_DUTY 31
> +#define MT6372_PMW_DUTY 255
Looks like these are limits by hardware?
Check with the datasheet if (BIT(x) - 1) makes more sense here.
...
> + switch (led_no) {
> + case MT6370_LED_ISNK1:
> + sel_field = F_LED1_DUTY;
> + break;
> + case MT6370_LED_ISNK2:
> + sel_field = F_LED2_DUTY;
> + break;
> + case MT6370_LED_ISNK3:
> + sel_field = F_LED3_DUTY;
> + break;
> + default:
> + sel_field = F_LED4_DUTY;
Missed break;
> + }
...
> + switch (led_no) {
> + case MT6370_LED_ISNK1:
> + sel_field = F_LED1_FREQ;
> + break;
> + case MT6370_LED_ISNK2:
> + sel_field = F_LED2_FREQ;
> + break;
> + case MT6370_LED_ISNK3:
> + sel_field = F_LED3_FREQ;
> + break;
> + default:
> + sel_field = F_LED4_FREQ;
Ditto.
> + }
...
> + switch (led_no) {
> + case MT6370_LED_ISNK1:
> + case MT6370_LED_ISNK2:
> + case MT6370_LED_ISNK3:
> + *base = MT6370_REG_RGB1_TR + led_no * 3;
> + break;
> + default:
> + *base = MT6370_REG_RGB_CHRIND_TR;
Ditto.
It seems you dropped them for all switch-cases. It's not goot, please
restore them back.
> + }
...
> + u8 val[P_MAX_PATTERNS / 2] = {0};
{ } should suffice
> + /*
> + * Pattern list
> + * tr1: byte 0, b'[7: 4]
> + * tr2: byte 0, b'[3: 0]
> + * tf1: byte 1, b'[7: 4]
> + * tf2: byte 1, b'[3: 0]
> + * ton: byte 2, b'[7: 4]
> + * toff: byte 2, b'[3: 0]
> + */
> + for (i = 0; i < P_MAX_PATTERNS; i++) {
> + curr = pattern + i;
> +
> + sel_range = i == P_LED_TOFF ? R_LED_TOFF : R_LED_TRFON;
> +
> + linear_range_get_selector_within(priv->ranges + sel_range,
> + curr->delta_t, &sel);
> +
> + val[i / 2] |= sel << (4 * ((i + 1) % 2));
> + }
> +
> + memcpy(pattern_val, val, 3);
> + return 0;
> +}
...
> +out:
out_unlock:
> + mutex_unlock(&priv->lock);
> +
> + return ret;
...
> +out:
Ditto. And so on.
> + mutex_unlock(&priv->lock);
> +
> + return ret;
...
> + sub_led = devm_kzalloc(priv->dev,
> + sizeof(*sub_led) * MC_CHANNEL_NUM,
> + GFP_KERNEL);
NIH devm_kcalloc(). Also check if you really need zeroed data.
> + if (!sub_led)
> + return -ENOMEM;
...
> + ret = fwnode_property_read_u32(child, "color", &color);
> + if (ret) {
> + dev_err(priv->dev,
> + "led %d, no color specified\n",
> + led->index);
> + return ret;
return dev_err_probe(...) ; ?
Ditto for many places in your entire series.
> + }
...
> + priv = devm_kzalloc(&pdev->dev,
> + struct_size(priv, leds, count), GFP_KERNEL);
At least one parameter can be placed on the previous line.
> + if (!priv)
> + return -ENOMEM;
--
With Best Regards,
Andy Shevchenko
