On Mon, Jan 17, 2022 at 2:47 PM Florian Eckert <fe@xxxxxxxxxx> wrote:
>
> Introducing the KTD2061/58/59/60 RGB LED drivers. The difference in
> these are the address numbers on the I2C bus that the device listens to.
>
> All KT20xx units can drive up to 12 LEDs.
>
> Due to the hardware limitation, we can only set 7 colors and the color
> black (LED off) for each LED independently and not the full RGB range.
> This is because the chip only has two color registers.
>
> To control the LEDs independently, the chip has to be configured in a
> special way.
>
> Color register 0 must be loaded with the current value 0mA, and color
> register 1 must be loaded with the value 'kinetic,led-current' from the
> device tree node. If the property is omitted, the register is loaded
> with the default value (0x28 = 5mA).
>
> To select a color for an LED, a combination must be written to the color
> selection register of that LED. This range for selecting the value is 3
> bits wide (RGB). A '0' in any of the bits uses color register '0' and a
> '1' uses color register '1'.
>
> So we could choose the following combination for each LED:
> R G B
> 0 0 0 = Black (off)
> 0 0 1 = Blue
> 0 1 0 = green
> 0 1 1 = Cyan
> 1 0 0 = Red
> 1 0 1 = Magenta
> 1 1 0 = Yellow
> 1 1 1 = White
Thanks for an update, my comments below.
> Signed-off-by: Florian Eckert <fe@xxxxxxxxxx>
> ---
> MAINTAINERS | 6 +
> drivers/leds/Kconfig | 12 +
> drivers/leds/Makefile | 1 +
> drivers/leds/leds-ktd20xx.c | 581 ++++++++++++++++++++++++++++++++++++
> 4 files changed, 600 insertions(+)
> create mode 100644 drivers/leds/leds-ktd20xx.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index a58544f7b699..04d68985d348 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -10739,6 +10739,12 @@ S: Maintained
> F: Documentation/devicetree/bindings/leds/backlight/kinetic,ktd253.yaml
> F: drivers/video/backlight/ktd253-backlight.c
>
> +KTD20XX LED CONTROLLER DRIVER
> +M: Florian Eckert <fe@xxxxxxxxxx>
> +L: linux-leds@xxxxxxxxxxxxxxx
> +S: Maintained
> +F: drivers/leds/leds-ktd20xx.c
> +
> KTEST
> M: Steven Rostedt <rostedt@xxxxxxxxxxx>
> M: John Hawley <warthog9@xxxxxxxxxxxxxx>
> diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
> index 6090e647daee..a96e6bf7918b 100644
> --- a/drivers/leds/Kconfig
> +++ b/drivers/leds/Kconfig
> @@ -157,6 +157,18 @@ config LEDS_EL15203000
> To compile this driver as a module, choose M here: the module
> will be called leds-el15203000.
>
> +config LEDS_KTD20XX
> + tristate "LED Support for KTD2061/58/59/60 LED driver chip"
> + depends on LEDS_CLASS && I2C
> + depends on LEDS_CLASS_MULTICOLOR
> + select REGMAP_I2C
> + help
> + If you say yes here you get support for the Kinetic
> + KTD2061, KTD2058, KTD2059 and KTD2060 LED driver.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called leds-ktd20xx.
> +
> config LEDS_TURRIS_OMNIA
> tristate "LED support for CZ.NIC's Turris Omnia"
> depends on LEDS_CLASS_MULTICOLOR
> diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
> index e58ecb36360f..5a86e72ea722 100644
> --- a/drivers/leds/Makefile
> +++ b/drivers/leds/Makefile
> @@ -34,6 +34,7 @@ obj-$(CONFIG_LEDS_IP30) += leds-ip30.o
> obj-$(CONFIG_LEDS_IPAQ_MICRO) += leds-ipaq-micro.o
> obj-$(CONFIG_LEDS_IS31FL319X) += leds-is31fl319x.o
> obj-$(CONFIG_LEDS_IS31FL32XX) += leds-is31fl32xx.o
> +obj-${CONFIG_LEDS_KTD20XX} += leds-ktd20xx.o
> obj-$(CONFIG_LEDS_LM3530) += leds-lm3530.o
> obj-$(CONFIG_LEDS_LM3532) += leds-lm3532.o
> obj-$(CONFIG_LEDS_LM3533) += leds-lm3533.o
> diff --git a/drivers/leds/leds-ktd20xx.c b/drivers/leds/leds-ktd20xx.c
> new file mode 100644
> index 000000000000..1207bb453594
> --- /dev/null
> +++ b/drivers/leds/leds-ktd20xx.c
> @@ -0,0 +1,581 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * LEDs driver for the Kinetic KDT20xx device
> + *
> + * Copyright (C) 2021 TDT AG
> + * Florian Eckert <fe@xxxxxxxxxx>
A bit of a strange indentation. Missed Author: ?
> + */
> +
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/leds.h>
> +#include <linux/led-class-multicolor.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/property.h>
> +#include <linux/regmap.h>
> +
> +/* I2C Register Map */
> +#define KTD20XX_ID 0x00
> +#define KTD20XX_MONITOR 0x01
> +#define KTD20XX_CONTROL 0x02
> +
> +/* Color0 Configuration Registers */
> +#define KTD20XX_IRED0 0x03
> +#define KTD20XX_IGRN0 0x04
> +#define KTD20XX_IBLU0 0x05
> +
> +/* Color1 Configuration Registers */
> +#define KTD20XX_IRED1 0x06
> +#define KTD20XX_IGRN1 0x07
> +#define KTD20XX_IBLU1 0x08
> +
> +/* Selection Configuration Register */
> +#define KTD20XX_ISELA12 0x09
> +#define KTD20XX_ISELA34 0x0A
> +#define KTD20XX_ISELB12 0x0B
> +#define KTD20XX_ISELB34 0x0C
> +#define KTD20XX_ISELC12 0x0D
> +#define KTD20XX_ISELC34 0x0E
> +
> +#define KTD20XX_MAX_LEDS 12
> +#define KTD20XX_LED_CHANNELS 3
> +
> +enum ktd20xx_led_number {
> + /* ISELA12 */
> + RGB_A1,
> + RGB_A2,
> + /* ISELA34 */
> + RGB_A3,
> + RGB_A4,
> + /* ISELB12 */
> + RGB_B1,
> + RGB_B2,
> + /* ISELB34 */
> + RGB_B3,
> + RGB_B4,
> + /* ISELC12 */
> + RGB_C1,
> + RGB_C2,
> + /* ISELC34 */
> + RGB_C3,
> + RGB_C4,
> +};
> +
> +enum ktd20xx_control_mode {
> + CONTROL_MODE_OFF,
> + CONTROL_MODE_NIGHT,
> + CONTROL_MODE_NORMAL,
> + CONTROL_MODE_RESET,
> +};
> +
> +static const struct reg_default ktd20xx_reg_defs[] = {
> + /* Color0 Configuration Registers */
> + {KTD20XX_IRED0, 0x28},
> + {KTD20XX_IGRN0, 0x28},
> + {KTD20XX_IBLU0, 0x28},
> + /* Color1 Configuration Registers */
> + {KTD20XX_IRED1, 0x60},
> + {KTD20XX_IGRN1, 0x60},
> + {KTD20XX_IBLU1, 0x60},
> + /* Selection Configuration Register */
> + {KTD20XX_ISELA12, 0x00},
> + {KTD20XX_ISELA34, 0x00},
> + {KTD20XX_ISELB12, 0x00},
> + {KTD20XX_ISELB34, 0x00},
> + {KTD20XX_ISELC12, 0x00},
> + {KTD20XX_ISELC34, 0x00}
> +};
> +
> +/* Chip values */
> +static const struct reg_field kt20xx_control_mode = REG_FIELD(KTD20XX_CONTROL, 6, 7);
> +static const struct reg_field kt20xx_faderate = REG_FIELD(KTD20XX_CONTROL, 0, 2);
> +static const struct reg_field kt20xx_vendor = REG_FIELD(KTD20XX_ID, 5, 7);
> +static const struct reg_field kt20xx_chip_id = REG_FIELD(KTD20XX_ID, 0, 4);
> +static const struct reg_field kt20xx_chip_rev = REG_FIELD(KTD20XX_MONITOR, 4, 7);
> +
> +/* ISELA1 and ISELA2 */
> +static const struct reg_field kt20xx_a1_select = REG_FIELD(KTD20XX_ISELA12, 4, 6);
> +static const struct reg_field kt20xx_a1_enable = REG_FIELD(KTD20XX_ISELA12, 7, 7);
> +static const struct reg_field kt20xx_a2_select = REG_FIELD(KTD20XX_ISELA12, 0, 2);
> +static const struct reg_field kt20xx_a2_enable = REG_FIELD(KTD20XX_ISELA12, 3, 3);
> +
> +/* ISELA3 and ISELA4 */
> +static const struct reg_field kt20xx_a3_select = REG_FIELD(KTD20XX_ISELA34, 4, 6);
> +static const struct reg_field kt20xx_a3_enable = REG_FIELD(KTD20XX_ISELA34, 7, 7);
> +static const struct reg_field kt20xx_a4_select = REG_FIELD(KTD20XX_ISELA34, 0, 2);
> +static const struct reg_field kt20xx_a4_enable = REG_FIELD(KTD20XX_ISELA34, 3, 3);
> +
> +/* ISELB1 and ISELB2 */
> +static const struct reg_field kt20xx_b1_select = REG_FIELD(KTD20XX_ISELB12, 4, 6);
> +static const struct reg_field kt20xx_b1_enable = REG_FIELD(KTD20XX_ISELB12, 7, 7);
> +static const struct reg_field kt20xx_b2_select = REG_FIELD(KTD20XX_ISELB12, 0, 2);
> +static const struct reg_field kt20xx_b2_enable = REG_FIELD(KTD20XX_ISELB12, 3, 3);
> +
> +/* ISELB3 and ISELB4 */
> +static const struct reg_field kt20xx_b3_select = REG_FIELD(KTD20XX_ISELB34, 4, 6);
> +static const struct reg_field kt20xx_b3_enable = REG_FIELD(KTD20XX_ISELB34, 7, 7);
> +static const struct reg_field kt20xx_b4_select = REG_FIELD(KTD20XX_ISELB34, 0, 2);
> +static const struct reg_field kt20xx_b4_enable = REG_FIELD(KTD20XX_ISELB34, 3, 3);
> +
> +/* ISELC1 and ISELC2 */
> +static const struct reg_field kt20xx_c1_select = REG_FIELD(KTD20XX_ISELC12, 4, 6);
> +static const struct reg_field kt20xx_c1_enable = REG_FIELD(KTD20XX_ISELC12, 7, 7);
> +static const struct reg_field kt20xx_c2_select = REG_FIELD(KTD20XX_ISELC12, 0, 2);
> +static const struct reg_field kt20xx_c2_enable = REG_FIELD(KTD20XX_ISELC12, 3, 3);
> +
> +/* ISELC3 and ISELC4 */
> +static const struct reg_field kt20xx_c3_select = REG_FIELD(KTD20XX_ISELC34, 4, 6);
> +static const struct reg_field kt20xx_c3_enable = REG_FIELD(KTD20XX_ISELC34, 7, 7);
> +static const struct reg_field kt20xx_c4_select = REG_FIELD(KTD20XX_ISELC34, 0, 2);
> +static const struct reg_field kt20xx_c4_enable = REG_FIELD(KTD20XX_ISELC34, 3, 3);
> +
> +static const struct regmap_range ktd20xx_volatile_ranges = {
> + .range_min = KTD20XX_ID,
> + .range_max = KTD20XX_CONTROL,
> +};
> +
> +static const struct regmap_access_table ktd20xx_volatile_table = {
> + .yes_ranges = &ktd20xx_volatile_ranges,
> + .n_yes_ranges = 1,
> +};
> +
> +static const struct regmap_range ktd20xx_readable_ranges = {
> + .range_min = KTD20XX_ID,
> + .range_max = KTD20XX_MONITOR,
> +};
> +
> +static const struct regmap_access_table ktd20xx_readable_table = {
> + .yes_ranges = &ktd20xx_readable_ranges,
> + .n_yes_ranges = 1,
> +};
> +
> +static const struct regmap_config ktd20xx_regmap_config = {
> + .name = "ktd20xx_regmap",
> + .reg_bits = 8,
> + .val_bits = 8,
> +
> + .max_register = KTD20XX_ISELC34,
> +
> + .volatile_table = &ktd20xx_volatile_table,
> + .rd_table = &ktd20xx_readable_table,
> +
> + .reg_defaults = ktd20xx_reg_defs,
> + .num_reg_defaults = ARRAY_SIZE(ktd20xx_reg_defs),
> + .cache_type = REGCACHE_FLAT,
> +};
> +
> +struct ktd20xx_led {
> + struct led_classdev_mc mc_cdev;
> + struct mc_subled subled_info[KTD20XX_LED_CHANNELS];
> + int index;
> + struct regmap_field *enable;
> + struct regmap_field *select;
> + struct ktd20xx *chip;
> +};
> +
> +struct ktd20xx {
> + struct mutex lock;
> + struct i2c_client *client;
> + struct regmap *regmap;
> + struct device *dev;
> + struct regmap_field *control_mode;
> + struct regmap_field *faderate;
> + struct regmap_field *vendor;
> + struct regmap_field *chip_id;
> + struct regmap_field *chip_rev;
> + struct ktd20xx_led leds[KTD20XX_MAX_LEDS];
> +};
> +
> +static int ktd20xx_hwinit(struct ktd20xx *chip)
> +{
> + struct device *dev = &chip->client->dev;
> + int ret;
> + unsigned int value;
> +
> + /*
> + * If the device tree property 'kinetc,led-current' is found
> + * then set this value into the color0 register as the max current
> + * for all color channel LEDs. If this poperty is not set then
> + * use the default value 0x28 set by the chip after a hardware reset.
> + * The hardware default value 0x28 corresponds to 5mA.
> + */
> + ret = device_property_read_u32(dev, "kinetic,led-current", &value);
> + if (ret == 0) {
> + dev_info(dev, "property 'kinetic,led-current' found. Using value 0x%02x.\n",
> + value);
Why _info? WHo needs this noise in the logs? Perhaps you meant _dbg?
> + regmap_write(chip->regmap, KTD20XX_IRED0, value);
> + regmap_write(chip->regmap, KTD20XX_IGRN0, value);
> + regmap_write(chip->regmap, KTD20XX_IBLU0, value);
> + } else {
> + dev_warn(dev, "property 'kinetic,led-current' not found. Using default hardware value 0x28 (5mA).\n");
> + }
Can we use the standard pattern, please?
I.e.
if (ret) {
...
} else {
...
}
> +
> + /* Set color1 register current value to 0x00 and therefor 0mA */
> + regmap_write(chip->regmap, KTD20XX_IRED1, 0);
> + regmap_write(chip->regmap, KTD20XX_IGRN1, 0);
> + regmap_write(chip->regmap, KTD20XX_IBLU1, 0);
> +
> + /* Enable chip to run in 'normal mode' */
> + regmap_field_write(chip->control_mode, CONTROL_MODE_NORMAL);
> +
> + return 0;
> +}
> +
> +static struct ktd20xx_led *mcled_cdev_to_led(struct led_classdev_mc *mc_cdev)
> +{
> + return container_of(mc_cdev, struct ktd20xx_led, mc_cdev);
> +}
> +
> +static int ktd20xx_brightness_set(struct led_classdev *cdev,
> + enum led_brightness brightness)
> +{
> + struct led_classdev_mc *mc_dev = lcdev_to_mccdev(cdev);
> + struct ktd20xx_led *led = mcled_cdev_to_led(mc_dev);
> + struct device *dev = led->chip->dev;
> + int ret = 0;
Redundant assignment
> + int i = 0;
Ditto.
> + unsigned int rgb = 0;
Move assignment closer to its first use.
> + mutex_lock(&led->chip->lock);
> + ret = regmap_field_write(led->enable, brightness ? 1 : 0);
> + if (ret) {
> + dev_err(dev, "Cannot set enable flag of LED %d error: %d\n",
> + led->index, ret);
> + goto out;
> + }
> +
> + for (i = 0; i < led->mc_cdev.num_colors; i++) {
> + unsigned int intensity = mc_dev->subled_info[i].intensity;
> + unsigned int channel = mc_dev->subled_info[i].channel;
> +
> + if (intensity > 0)
> + rgb += BIT(channel);
Use bit operations instead, which will make it cleaner.
> + }
> +
> + /*
> + * To use the color0 registers default value after an hadware reset,
> + * if the device tree property 'kinetc,led-current' is not set,
> + * we have to 'invert' the rgb channel!
> + */
> + ret = regmap_field_write(led->select, ~rgb);
> + if (ret) {
> + dev_err(dev, "Can not set RGB for LED %d error: %d\n",
> + led->index, ret);
> + goto out;
> + }
> +out:
out_unlock:
> + mutex_unlock(&led->chip->lock);
> + return ret;
> +}
> +
> +static int ktd20xx_probe_dt(struct ktd20xx *chip)
> +{
> + struct fwnode_handle *child = NULL;
> + struct led_init_data init_data = {};
> + struct led_classdev *led_cdev;
> + struct ktd20xx_led *led;
> + struct device *dev = &chip->client->dev;
> + int i = 0;
Move the assignment closer to its first user.
> + int ret = -EINVAL;
How does it work? I mean this assignment.
> + int color;
> +
> + device_for_each_child_node(chip->dev, child) {
> + led = &chip->leds[i];
> +
> + ret = fwnode_property_read_u32(child, "reg", &led->index);
> + if (ret) {
> + dev_err(dev, "missing property 'reg'\n");
> + goto child_out;
> + }
> + if (led->index >= KTD20XX_MAX_LEDS) {
> + dev_warn(dev, "property 'reg' must contain value between '0' and '%i'\n",
> + KTD20XX_MAX_LEDS);
_warn is not in alignment with the actions the code makes at this condition.
> + ret = -EINVAL;
> + goto child_out;
> + }
> +
> + ret = fwnode_property_read_u32(child, "color", &color);
> + if (ret) {
> + dev_err(dev, "missing property 'color'\n");
> + goto child_out;
> + }
> + if (color != LED_COLOR_ID_MULTI) {
> + dev_warn(dev, "wrong property 'color' must be 'LED_COLOR_ID_MULTI'\n");
Ditto.
> + ret = -EINVAL;
> + goto child_out;
> + }
> +
> + led->subled_info[0].color_index = LED_COLOR_ID_RED;
> + led->subled_info[0].channel = 2;
> + led->subled_info[1].color_index = LED_COLOR_ID_GREEN;
> + led->subled_info[1].channel = 1;
> + led->subled_info[2].color_index = LED_COLOR_ID_BLUE;
> + led->subled_info[2].channel = 0;
> +
> + led->mc_cdev.subled_info = led->subled_info;
> + led->mc_cdev.num_colors = KTD20XX_LED_CHANNELS;
> +
> + init_data.fwnode = child;
> +
> + led->chip = chip;
> + led_cdev = &led->mc_cdev.led_cdev;
> + led_cdev->brightness_set_blocking = ktd20xx_brightness_set;
> +
> + switch (led->index) {
> + case RGB_A1:
> + led->select = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_a1_select);
> + led->enable = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_a1_enable);
> + break;
> + case RGB_A2:
> + led->select = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_a2_select);
> + led->enable = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_a2_enable);
> + break;
> + case RGB_A3:
> + led->select = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_a3_select);
> + led->enable = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_a3_enable);
> + break;
> + case RGB_A4:
> + led->select = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_a4_select);
> + led->enable = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_a4_enable);
> + break;
> + case RGB_B1:
> + led->select = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_b1_select);
> + led->enable = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_b1_enable);
> + break;
> + case RGB_B2:
> + led->select = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_b2_select);
> + led->enable = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_b2_enable);
> + break;
> + case RGB_B3:
> + led->select = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_b3_select);
> + led->enable = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_b3_enable);
> + break;
> + case RGB_B4:
> + led->select = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_b4_select);
> + led->enable = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_b4_enable);
> + break;
> + case RGB_C1:
> + led->select = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_c1_select);
> + led->enable = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_c1_enable);
> + break;
> + case RGB_C2:
> + led->select = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_c2_select);
> + led->enable = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_c2_enable);
> + break;
> + case RGB_C3:
> + led->select = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_c3_select);
> + led->enable = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_c3_enable);
> + break;
> + case RGB_C4:
> + led->select = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_c4_select);
> + led->enable = devm_regmap_field_alloc(chip->dev,
> + chip->regmap, kt20xx_c4_enable);
> + break;
> + }
> + ret = devm_led_classdev_multicolor_register_ext(&chip->client->dev,
What's the difference between &client->dev and chip->dev? If none, why
do you have both in the structure?
> + &led->mc_cdev,
> + &init_data);
> +
> + if (ret) {
> + dev_err(&chip->client->dev, "led register err: %d\n", ret);
> + goto child_out;
> + }
> +
> + i++;
> + }
> +
> + return 0;
> +
> +child_out:
> + fwnode_handle_put(child);
> + return ret;
> +}
> +
> +/*
> + * The chip also offers the option "Night Mode".
> + * All LED current settings are divided by 16 for a 0 to 1.5mA current
> + * setting range.
> + */
> +static ssize_t nightmode_show(struct device *dev, struct device_attribute *a,
> + char *buf)
> +{
> + struct ktd20xx *chip = dev_get_drvdata(dev);
> + unsigned int value;
> +
> + mutex_lock(&chip->lock);
> + regmap_field_read(chip->control_mode, &value);
> + mutex_unlock(&chip->lock);
> +
> + return sysfs_emit(buf, "%d\n", value == CONTROL_MODE_NIGHT ? 1 : 0);
> +}
> +
> +static ssize_t nightmode_store(struct device *dev, struct device_attribute *a,
> + const char *buf, size_t count)
> +{
> + struct ktd20xx *chip = dev_get_drvdata(dev);
> + bool value;
> + int ret;
> + if (kstrtobool(buf, &value))
> + return -EINVAL;
Do not hide the returned value from kstrbool().
> + mutex_lock(&chip->lock);
> + ret = regmap_field_write(chip->control_mode,
> + value == 1 ? CONTROL_MODE_NIGHT : CONTROL_MODE_NORMAL);
> + mutex_unlock(&chip->lock);
> +
> + if (ret < 0)
> + return ret;
> +
> + return count;
> +}
> +static DEVICE_ATTR_RW(nightmode);
> +
> +static struct attribute *ktd20xx_led_controller_attrs[] = {
> + &dev_attr_nightmode.attr,
> + NULL
> +};
> +ATTRIBUTE_GROUPS(ktd20xx_led_controller);
> +
> +static int ktd20xx_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct ktd20xx *chip;
> + unsigned int vendor;
> + unsigned int chip_id;
> + unsigned int chip_rev;
> + int ret;
> +
> + chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL);
> + if (!chip)
> + return -ENOMEM;
> +
> + mutex_init(&chip->lock);
> + chip->client = client;
> + chip->dev = &client->dev;
> + i2c_set_clientdata(client, chip);
> +
> + chip->regmap = devm_regmap_init_i2c(client, &ktd20xx_regmap_config);
> + if (IS_ERR(chip->regmap)) {
> + dev_err_probe(&client->dev, PTR_ERR(chip->regmap),
> + "Failed to allocate register map\n");
> + goto error;
> + }
> +
> + chip->control_mode = devm_regmap_field_alloc(chip->dev, chip->regmap,
> + kt20xx_control_mode);
> + chip->faderate = devm_regmap_field_alloc(chip->dev, chip->regmap,
> + kt20xx_faderate);
> + chip->vendor = devm_regmap_field_alloc(chip->dev, chip->regmap,
> + kt20xx_vendor);
> + chip->chip_id = devm_regmap_field_alloc(chip->dev, chip->regmap,
> + kt20xx_chip_id);
> + chip->chip_rev = devm_regmap_field_alloc(chip->dev, chip->regmap,
> + kt20xx_chip_rev);
> +
> + /* Reset all registers to hardware device default settings */
> + regmap_field_write(chip->control_mode, CONTROL_MODE_RESET);
> +
> + ret = regmap_field_read(chip->vendor, &vendor);
> + if (ret) {
> + dev_err_probe(&client->dev, ret, "Failed to read vendor\n");
> + goto error;
> + }
> +
> + ret = regmap_field_read(chip->chip_id, &chip_id);
> + if (ret) {
> + dev_err_probe(&client->dev, ret, "Failed to read chip id\n");
> + goto error;
> + }
> +
> + ret = regmap_field_read(chip->chip_rev, &chip_rev);
> + if (ret) {
> + dev_err_probe(&client->dev, ret, "Failed to read chip rev\n");
> + goto error;
> + }
> +
> + dev_info(&client->dev, "vendor: 0x%02x chip-id: 0x%02x chip-rev: 0x%02x\n",
> + vendor, chip_id, chip_rev);
> +
> + ret = ktd20xx_hwinit(chip);
> + if (ret)
> + goto error;
> +
> + ret = ktd20xx_probe_dt(chip);
> + if (ret)
> + goto error;
> +
> + return 0;
> +error:
err_destroy_mutex:
But...
> + mutex_destroy(&chip->lock);
> + return ret;
...here...
> +}
> +
> +static int ktd20xx_remove(struct i2c_client *client)
> +{
> + struct ktd20xx *chip = i2c_get_clientdata(client);
> +
> + mutex_lock(&chip->lock);
> + regmap_field_write(chip->control_mode, CONTROL_MODE_OFF);
> + mutex_unlock(&chip->lock);
> + mutex_destroy(&chip->lock);
...and here you have an ordering issue. You are not supposed to mix
devm with non-devm like you did. So, imagine what will happen here if
something will call regmap functions here.
> + return 0;
> +}
> +
> +static const struct i2c_device_id ktd20xx_id[] = {
> + { "ktd20xx", 0 },
> + {}
> +};
> +MODULE_DEVICE_TABLE(i2c, ktd20xx_id);
> +
> +static const struct of_device_id of_ktd20xx_leds_match[] = {
> + { .compatible = "kinetic,ktd20xx", },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, of_ktd20xx_leds_match);
> +
> +static struct i2c_driver ktd20xx_driver = {
> + .driver = {
> + .name = "ktd20xx",
> + .dev_groups = ktd20xx_led_controller_groups,
> + .of_match_table = of_ktd20xx_leds_match,
> + },
> + .probe = ktd20xx_probe,
> + .remove = ktd20xx_remove,
> + .id_table = ktd20xx_id
> +};
> +module_i2c_driver(ktd20xx_driver);
> +
> +MODULE_DESCRIPTION("Kinetic KTD20xx LED driver");
> +MODULE_AUTHOR("Florian Eckert <fe@xxxxxxxxxx>");
> +MODULE_LICENSE("GPL v2");
> --
> 2.20.1
>
--
With Best Regards,
Andy Shevchenko
