Convert the LEDs bindings of Maxim MAX77693 MUIC to DT schema format. The existing bindings were defined in ../bindings/mfd/max77693.txt. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxxxxx> --- .../bindings/leds/maxim,max77693.yaml | 105 ++++++++++++++++++ 1 file changed, 105 insertions(+) create mode 100644 Documentation/devicetree/bindings/leds/maxim,max77693.yaml diff --git a/Documentation/devicetree/bindings/leds/maxim,max77693.yaml b/Documentation/devicetree/bindings/leds/maxim,max77693.yaml new file mode 100644 index 000000000000..86a0005cf156 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/maxim,max77693.yaml @@ -0,0 +1,105 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/maxim,max77693.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim MAX77693 MicroUSB and Companion Power Management IC LEDs + +maintainers: + - Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxxxxx> + +description: | + This is a part of device tree bindings for Maxim MAX77693 MicroUSB Integrated + Circuit (MUIC). + + There are two LED outputs available - FLED1 and FLED2. Each of them can + control a separate LED or they can be connected together to double the + maximum current for a single connected LED. One LED is represented by one + child node. + + See also Documentation/devicetree/bindings/mfd/maxim,max77693.yaml for + additional information and example. + +properties: + compatible: + const: maxim,max77693-led + + maxim,boost-mode: + description: + In boost mode the device can produce up to 1.2A of total current on both + outputs. The maximum current on each output is reduced to 625mA then. If + not enabled explicitly, boost setting defaults to LEDS_BOOST_FIXED in + case both current sources are used. + See LEDS_BOOST_* in include/dt-bindings/leds/common.h. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + + maxim,boost-mvout: + description: | + Output voltage of the boost module in millivolts. + Valid values: 3300 - 5500, step by 25 (rounded down) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 3300 + maximum: 5500 + default: 3300 + + maxim,mvsys-min: + description: | + Low input voltage level in millivolts. Flash is not fired if chip + estimates that system voltage could drop below this level due to flash + power consumption. + Valid values: 2400 - 3400, step by 33 (rounded down) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 2400 + maximum: 3400 + default: 2400 + +patternProperties: + "^([a-z]+-)?led[01]?$": + type: object + $ref: common.yaml# + unevaluatedProperties: false + + properties: + led-sources: + allOf: + - minItems: 1 + maxItems: 2 + items: + minimum: 0 + maximum: 1 + + led-max-microamp: + description: | + Valid values for a LED connected to one FLED output: + 15625 - 250000, step by 15625 (rounded down) + Valid values for a LED connected to both FLED outputs: + 15625 - 500000, step by 15625 (rounded down) + + flash-max-microamp: + description: | + Valid values for a single LED connected to one FLED output + (boost mode must be turned off): + 15625 - 1000000, step by 15625 (rounded down) + Valid values for a single LED connected to both FLED outputs: + 15625 - 1250000, step by 15625 (rounded down) + Valid values for two LEDs case: + 15625 - 625000, step by 15625 (rounded down) + + flash-max-timeout-us: + description: | + Valid values: 62500 - 1000000, step by 62500 (rounded down) + minimum: 62500 + maximum: 1000000 + + required: + - flash-max-microamp + - flash-max-timeout-us + - led-max-microamp + - led-sources + +required: + - compatible + +additionalProperties: false -- 2.32.0
