Re: [PATCH] dt-bindings: leds: Document commonly used LED triggers

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 2020/12/10 14:14, Manivannan Sadhasivam wrote:
> This commit documents the LED triggers used commonly in the SoCs. Not
> all triggers are documented as some of them are very application specific.
> Most of the triggers documented here are currently used in devicetrees
> of many SoCs.
> 
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
> ---
>  .../devicetree/bindings/leds/common.yaml      | 72 ++++++++++++++-----
>  1 file changed, 54 insertions(+), 18 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/leds/common.yaml b/Documentation/devicetree/bindings/leds/common.yaml
> index f1211e7045f1..eee4eb7a4535 100644
> --- a/Documentation/devicetree/bindings/leds/common.yaml
> +++ b/Documentation/devicetree/bindings/leds/common.yaml
> @@ -79,24 +79,60 @@ properties:
>        the LED.
>      $ref: /schemas/types.yaml#definitions/string
>  
> -    enum:
> -        # LED will act as a back-light, controlled by the framebuffer system
> -      - backlight
> -        # LED will turn on (but for leds-gpio see "default-state" property in
> -        # Documentation/devicetree/bindings/leds/leds-gpio.yaml)
> -      - default-on
> -        # LED "double" flashes at a load average based rate
> -      - heartbeat
> -        # LED indicates disk activity
> -      - disk-activity
> -        # LED indicates IDE disk activity (deprecated), in new implementations
> -        # use "disk-activity"
> -      - ide-disk
> -        # LED flashes at a fixed, configurable rate
> -      - timer
> -        # LED alters the brightness for the specified duration with one software
> -        # timer (requires "led-pattern" property)
> -      - pattern
> +    oneOf:
> +      - items:
> +          - enum:
> +                # LED will act as a back-light, controlled by the framebuffer system
> +              - backlight
> +                # LED will turn on (but for leds-gpio see "default-state" property in
> +                # Documentation/devicetree/bindings/leds/leds-gpio.yaml)
> +              - default-on
> +                # LED "double" flashes at a load average based rate
> +              - heartbeat
> +                # LED indicates disk activity
> +              - disk-activity
> +                # LED indicates IDE disk activity (deprecated), in new implementations
> +                # use "disk-activity"
> +              - ide-disk
> +                # LED flashes at a fixed, configurable rate
> +              - timer
> +                # LED alters the brightness for the specified duration with one software
> +                # timer (requires "led-pattern" property)
> +              - pattern
> +                # LED indicates camera flash state
> +              - flash
> +                # LED indicates camera torch state
> +              - torch
> +                # LED indicates audio mute state
> +              - audio-mute
> +                # LED indicates mic mute state
> +              - audio-micmute
> +                # LED indicates bluetooth power state
> +              - bluetooth-power
> +                # LED indicates USB gadget activity
> +              - usb-gadget
> +                # LED indicates USB host activity
> +              - usb-host
> +                # LED indicates MTD memory activity
> +              - mtd
> +                # LED indicates NAND memory activity (deprecated),
> +                # in new implementations use "mtd"
> +              - nand-disk
> +                # LED indicates disk read activity
> +              - disk-read
> +                # LED indicates disk write activity
> +              - disk-write
> +                # No trigger assigned to the LED. This is the default mode
> +                # if trigger is absent
> +              - none
> +                # LED indicates activity of all CPUs
> +              - cpu
The triggers phy0tx and hci0-power are missed.

Since you've rewritten it, please consider sorting these property strings
in ascending alphabetical order.

> +      - items:
> +            # LED indicates activity of [N]th CPU
> +          - pattern: "^cpu[0-9][0-9]$"
should be ^cpu[0-9]{1,2}$, otherwise, it always requires two digit.

> +      - items:
> +            # LED indicates [N]th MMC storage activity
> +          - pattern: '^mmc[0-9][0-9]$'
should be '^mmc[0-9]{1,2}$'

Why CPU use "", and mmc use '',It's better to keep them consistent.

>  
>    led-pattern:
>      description: |
> 




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux OMAP]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux