On Wed, Mar 13, 2019 at 07:32:46AM -0500, Dan Murphy wrote: > Add the lm3532 device tree documentation. > Remove lm3532 device tree reference from the ti_lmu devicetree > documentation. > > With the addition of the dedicated lm3532 documentation the device > can be removed from the ti_lmu.txt. > > The reason for this is that the lm3532 dt documentation now defines > the ability to control LED output strings against different control > banks or groups multiple strings to be controlled by a single control > bank. > > Another addition was for ALS lighting control and configuration. The > LM3532 has a feature that can take in the ALS reading from 2 separate > ALS devices and adjust the brightness on the strings that are configured > to support this feature. > > Finally the device specific properties were moved to the parent node as these > properties are not control bank configurable. These include the runtime ramp > and the ALS configuration. > > Signed-off-by: Dan Murphy <dmurphy@xxxxxx> > --- > > v4 - Appended "ti," to TI specific properties, add enable gpio documentation, > removed an example, moved ramp to optional parent properties - https://lore.kernel.org/patchwork/patch/1050122/ > > v3 - No changes - https://lore.kernel.org/patchwork/patch/1049026/ > v2 - Fixed ramp-up and ramp-down properties, removed hard coded property values, > added ranges for variable properties, I did not change the label - https://lore.kernel.org/patchwork/patch/1048805/ > > > .../devicetree/bindings/leds/leds-lm3532.txt | 101 ++++++++++++++++++ > .../devicetree/bindings/mfd/ti-lmu.txt | 20 ---- > 2 files changed, 101 insertions(+), 20 deletions(-) > create mode 100644 Documentation/devicetree/bindings/leds/leds-lm3532.txt > > diff --git a/Documentation/devicetree/bindings/leds/leds-lm3532.txt b/Documentation/devicetree/bindings/leds/leds-lm3532.txt > new file mode 100644 > index 000000000000..ba793ef9b3b6 > --- /dev/null > +++ b/Documentation/devicetree/bindings/leds/leds-lm3532.txt > @@ -0,0 +1,101 @@ > +* Texas Instruments - lm3532 White LED driver with ambient light sensing > +capability. > + > +The LM3532 provides the 3 high-voltage, low-side current sinks. The device is > +programmable over an I2C-compatible interface and has independent > +current control for all three channels. The adaptive current regulation > +method allows for different LED currents in each current sink thus allowing > +for a wide variety of backlight and keypad applications. > + > +The main features of the LM3532 include dual ambient light sensor inputs > +each with 32 internal voltage setting resistors, 8-bit logarithmic and linear > +brightness control, dual external PWM brightness control inputs, and up to > +1000:1 dimming ratio with programmable fade in and fade out settings. > + > +Required properties: > + - compatible : "ti,lm3532" > + - reg : I2C slave address > + - #address-cells : 1 > + - #size-cells : 0 > + > +Optional properties: > + - enable-gpios : gpio pin to enable (active high)/disable the device. > + Range for ramp settings: 8us - 65536us This should be after the 2 ramp properties. With that, Reviewed-by: Rob Herring <robh@xxxxxxxxxx> > + - ramp-up-us - The Run time ramp rates/step are from one current > + set-point to another after the device has reached its > + initial target set point from turn-on > + - ramp-down-us - The Run time ramp rates/step are from one current > + set-point to another after the device has reached its > + initial target set point from turn-on
