Fix comments, debug functions and print strings. Rename backlight
structures to be more specific.
Signed-off-by: Petr Cvek <petr.cvek@xxxxxx>
---
arch/arm/mach-pxa/magician.c | 121 +++++++++++++++++++++++++++++++------------
1 file changed, 89 insertions(+), 32 deletions(-)
diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c
index 9e8698a..57da133 100644
--- a/arch/arm/mach-pxa/magician.c
+++ b/arch/arm/mach-pxa/magician.c
@@ -11,6 +11,46 @@
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
+ *
+ * NOTICE MDA Compact (T-mobile XDA) facts:
+ * On "LCD type = 1, system_rev = 2" (0x3a in CPLD)
+ * Samsung LTP280QV - valid LCD init sequence sequence:
+ * powerup: Vdigital->Vanalog->gate Voff->gate Von->data enable
+ * powerdown: data disable->gate Von->gate Voff->Vanalog->Vdigital
+ * Measured on PCB:
+ * GPIO106
+ * Affects VOFF, VON and other voltages
+ * Probably main reset pin for DC-DC converter
+ * GPIO75
+ * Must be AF0+OUT (WM leaves it to AF2+OUT), not LCD signal
+ * GPIO106 works only when GPIO75 is high (DC-DC power enable?)
+ * After LCD powerup, value is irrelevant
+ * GPIO104
+ * LCD VOFF (gate off voltage)
+ * GPIO105
+ * LCD VON (gate on voltage)
+ * FFUART (/dev/ttyS0) WM: 38400,8,n,1,crtscts (GSM data?)
+ * BTUART (/dev/ttyS1) WM: 115200,8,n,1,crtscts (GSM AT commands)
+ * Use a HTC line discipline: 0x02 channel(==0x16) data 0x02
+ * EGPIO(CPLD) should be always present (controls "all" supply power)
+ * For rootfs on MMC/SD: EGPIO module controls card power (in kernel)
+ * cpu-freq often freeze platform (errata?, use userspace gov)
+ * Do not use YUV420, (erratum E24) causes LCD hang (forever)
+ * Many GSM related pins are unknown
+ * gpio-rc-recv probably require lowpass filter (sw is OK)
+ * TODO EGPIO_MAGICIAN_IR_RECEIVE_SHUTDOWN
+ * FIXME AC charging blocks IrDA
+ * Unimplemented blocking of camera+power+reset, reset and door open reset
+ * Registers: htc-pasic3.h (but blocks charging too)
+ * Other PXA machines have wait_for_sync for ADS7846 (during LCD refresh)
+ * pda-power has not optimal charging (accu can be bloated)
+ * TODO Current switching works? Is gpio-regulator/bq24022 required?
+ * pdata supports alternative drivers (mutually exclusive modules)
+ * i2c-pxa vs i2c-gpio (SCCB)
+ * pwm_bl vs gpio_backlight
+ * pxa27x_udc vs phy-gpio-vbus-usb
+ * physmap-flash vs pxa2xx-flash
+ *
*/
#include <linux/kernel.h>
@@ -57,31 +97,31 @@ static unsigned long magician_pin_config[] __initdata = {
GPIO80_nCS_4,
GPIO33_nCS_5,
- /* I2C */
+ /* I2C UDA1380 + OV9640 */
GPIO117_I2C_SCL,
GPIO118_I2C_SDA,
- /* PWM 0 */
+ /* PWM 0 - LCD backlight */
GPIO16_PWM0_OUT,
- /* I2S */
+ /* I2S UDA1380 capture */
GPIO28_I2S_BITCLK_OUT,
GPIO29_I2S_SDATA_IN,
GPIO31_I2S_SYNC,
GPIO113_I2S_SYSCLK,
- /* SSP 1 */
+ /* SSP 1 UDA1380 playback */
GPIO23_SSP1_SCLK,
GPIO24_SSP1_SFRM,
GPIO25_SSP1_TXD,
- /* SSP 2 */
+ /* SSP 2 TSC2046 touchscreen */
GPIO19_SSP2_SCLK,
GPIO14_SSP2_SFRM,
GPIO89_SSP2_TXD,
GPIO88_SSP2_RXD,
- /* MMC */
+ /* MMC/SD/SDHC slot */
GPIO32_MMC_CLK,
GPIO92_MMC_DAT_0,
GPIO109_MMC_DAT_1,
@@ -92,7 +132,7 @@ static unsigned long magician_pin_config[] __initdata = {
/* LCD */
GPIOxx_LCD_TFT_16BPP,
- /* QCI */
+ /* QCI camera interface */
GPIO12_CIF_DD_7,
GPIO17_CIF_DD_6,
GPIO50_CIF_DD_3,
@@ -120,11 +160,12 @@ static unsigned long magician_pin_config[] __initdata = {
};
/*
- * IRDA
+ * IrDA
*/
static struct pxaficp_platform_data magician_ficp_info = {
.gpio_pwdown = GPIO83_MAGICIAN_nIR_EN,
+ /* TODO test with FIR dongle */
.transceiver_cap = IR_SIRMODE | IR_OFF,
};
@@ -174,8 +215,8 @@ static struct platform_device gpio_keys = {
/*
* EGPIO (Xilinx CPLD)
- *
- * 7 32-bit aligned 8-bit registers: 3x output, 1x irq, 3x input
+ * 32-bit aligned
+ * 7x 8-bit registers: 3x output, 1x irq, 3x input
*/
static struct resource egpio_resources[] = {
@@ -197,7 +238,11 @@ static struct htc_egpio_chip egpio_chips[] = {
.gpio_base = MAGICIAN_EGPIO(0, 0),
.num_gpios = 24,
.direction = HTC_EGPIO_OUTPUT,
- .initial_values = 0x40, /* EGPIO_MAGICIAN_GSM_RESET */
+
+ /*
+ * Depends on modules configuration
+ */
+ .initial_values = 0x40,
},
[1] = {
.reg_start = 4,
@@ -228,7 +273,7 @@ static struct platform_device egpio = {
};
/*
- * LCD - Toppoly TD028STEB1 or Samsung LTP280QV
+ * PXAFB LCD - Toppoly TD028STEB1 or Samsung LTP280QV
*/
static struct pxafb_mode_info toppoly_modes[] = {
@@ -265,10 +310,9 @@ static struct pxafb_mode_info samsung_modes[] = {
static void toppoly_lcd_power(int on, struct fb_var_screeninfo *si)
{
- pr_debug("Toppoly LCD power\n");
+ pr_debug("Toppoly LCD power: %s\n", on ? "on" : "off");
if (on) {
- pr_debug("on\n");
gpio_set_value(EGPIO_MAGICIAN_TOPPOLY_POWER, 1);
gpio_set_value(GPIO106_MAGICIAN_LCD_POWER_3, 1);
udelay(2000);
@@ -280,8 +324,7 @@ static void toppoly_lcd_power(int on, struct fb_var_screeninfo *si)
udelay(2000);
gpio_set_value(GPIO105_MAGICIAN_LCD_POWER_2, 1);
} else {
- pr_debug("off\n");
- msleep(15);
+ mdelay(15);
gpio_set_value(GPIO105_MAGICIAN_LCD_POWER_2, 0);
udelay(500);
gpio_set_value(GPIO104_MAGICIAN_LCD_POWER_1, 0);
@@ -293,10 +336,9 @@ static void toppoly_lcd_power(int on, struct fb_var_screeninfo *si)
static void samsung_lcd_power(int on, struct fb_var_screeninfo *si)
{
- pr_debug("Samsung LCD power\n");
+ pr_debug("Samsung LCD power: %s\n", on ? "on" : "off");
if (on) {
- pr_debug("on\n");
if (system_rev < 3)
gpio_set_value(GPIO75_MAGICIAN_SAMSUNG_POWER, 1);
else
@@ -309,7 +351,6 @@ static void samsung_lcd_power(int on, struct fb_var_screeninfo *si)
gpio_set_value(GPIO105_MAGICIAN_LCD_POWER_2, 1);
mdelay(10);
} else {
- pr_debug("off\n");
mdelay(10);
gpio_set_value(GPIO105_MAGICIAN_LCD_POWER_2, 0);
mdelay(30);
@@ -346,8 +387,8 @@ static struct pxafb_mach_info samsung_info = {
*/
static struct gpio magician_bl_gpios[] = {
- { EGPIO_MAGICIAN_BL_POWER, GPIOF_DIR_OUT, "Backlight power" },
- { EGPIO_MAGICIAN_BL_POWER2, GPIOF_DIR_OUT, "Backlight power 2" },
+ { EGPIO_MAGICIAN_BL_POWER, GPIOF_DIR_OUT, "Backlight power" },
+ { EGPIO_MAGICIAN_BL_POWER2, GPIOF_DIR_OUT, "Extra backlight power" },
};
static int magician_backlight_init(struct device *dev)
@@ -357,6 +398,7 @@ static int magician_backlight_init(struct device *dev)
static int magician_backlight_notify(struct device *dev, int brightness)
{
+ pr_debug("Brightness = %i\n", brightness);
gpio_set_value(EGPIO_MAGICIAN_BL_POWER, brightness);
if (brightness >= 200) {
gpio_set_value(EGPIO_MAGICIAN_BL_POWER2, 1);
@@ -372,7 +414,13 @@ static void magician_backlight_exit(struct device *dev)
gpio_free_array(ARRAY_AND_SIZE(magician_bl_gpios));
}
-static struct platform_pwm_backlight_data backlight_data = {
+/*
+ * LCD backlight by PWM (main)
+ * PWM frequency for MP1521 should be:
+ * 100-400 Hz = 2 .5*10^6 - 10 *10^6 ns
+ */
+
+static struct platform_pwm_backlight_data pwm_backlight_data = {
.pwm_id = 0,
.max_brightness = 272,
.dft_brightness = 100,
@@ -383,12 +431,12 @@ static struct platform_pwm_backlight_data backlight_data = {
.exit = magician_backlight_exit,
};
-static struct platform_device backlight = {
+static struct platform_device pwm_backlight = {
.name = "pwm-backlight",
.id = -1,
.dev = {
.parent = &pxa27x_device_pwm0.dev,
- .platform_data = &backlight_data,
+ .platform_data = &pwm_backlight_data,
},
};
@@ -422,6 +470,10 @@ static struct platform_device leds_gpio = {
},
};
+/*
+ * PASIC3 LEDs
+ */
+
static struct pasic3_led pasic3_leds[] = {
{
.led = {
@@ -459,7 +511,7 @@ static struct pasic3_leds_machinfo pasic3_leds_info = {
};
/*
- * PASIC3 with DS1WM
+ * PASIC3 DS1WM
*/
static struct resource pasic3_resources[] = {
@@ -477,8 +529,8 @@ static struct resource pasic3_resources[] = {
};
static struct pasic3_platform_data pasic3_platform_data = {
- .led_pdata = &pasic3_leds_info,
.clock_rate = 4000000,
+ .led_pdata = &pasic3_leds_info,
};
static struct platform_device pasic3 = {
@@ -517,7 +569,7 @@ static struct platform_device gpio_vbus = {
};
/*
- * External power
+ * Charging functions
*/
static int power_supply_init(struct device *dev)
@@ -539,6 +591,10 @@ static char *magician_supplicants[] = {
"ds2760-battery.0", "backup-battery"
};
+/*
+ * pda_power Li-ion charger
+ */
+
static struct pda_power_pdata power_supply_info = {
.init = power_supply_init,
.is_ac_online = magician_is_ac_online,
@@ -575,7 +631,7 @@ static struct platform_device power_supply = {
};
/*
- * Battery charger
+ * Charging current switch
*/
static struct regulator_consumer_supply bq24022_consumers[] = {
@@ -695,7 +751,7 @@ static struct platform_device strataflash = {
};
/*
- * I2C
+ * PXA I2C normal controller (main)
*/
static struct i2c_pxa_platform_data i2c_info = {
@@ -709,7 +765,7 @@ static struct i2c_pxa_platform_data i2c_info = {
static struct platform_device *devices[] __initdata = {
&gpio_keys,
&egpio,
- &backlight,
+ &pwm_backlight,
&pasic3,
&bq24022,
&gpio_vbus,
@@ -734,9 +790,10 @@ static void __init magician_init(void)
int err;
pxa2xx_mfp_config(ARRAY_AND_SIZE(magician_pin_config));
+
err = gpio_request_array(ARRAY_AND_SIZE(magician_global_gpios));
if (err)
- pr_err("magician: Failed to request GPIOs: %d\n", err);
+ pr_err("magician: Failed to request global GPIOs: %d\n", err);
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
@@ -761,7 +818,7 @@ static void __init magician_init(void)
pr_info("LCD type: %s\n", lcd_select ? "Samsung" : "Toppoly");
if (lcd_select && (system_rev < 3))
gpio_request_one(GPIO75_MAGICIAN_SAMSUNG_POWER,
- GPIOF_OUT_INIT_LOW, "SAMSUNG_POWER");
+ GPIOF_OUT_INIT_LOW, "Samsung LCD Power");
pxa_set_fb_info(NULL,
lcd_select ? &samsung_info : &toppoly_info);
} else
--
1.7.12.1
--
To unsubscribe from this list: send the line "unsubscribe linux-leds" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
