This patch fixes build warnings as below:
drivers/leds/leds-lp5523.c: In function 'lp5523_selftest':
drivers/leds/leds-lp5523.c:496:18: warning: 'adc' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5523.c:471:5: warning: 'vdd' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5523.c: In function 'lp5523_probe':
drivers/leds/leds-lp5523.c:252:9: warning: 'status' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5523.c:201:5: note: 'status' was declared here
If lp5523_read() returns an error, problems will happen. Thus,
when lp5523_read() returns an error, it should be handled.
Signed-off-by: Jingoo Han <jg1.han@xxxxxxxxxxx>
---
drivers/leds/leds-lp5523.c | 20 +++++++++++++++++---
1 files changed, 17 insertions(+), 3 deletions(-)
diff --git a/drivers/leds/leds-lp5523.c b/drivers/leds/leds-lp5523.c
index 97994ff..4ddf7b4 100644
--- a/drivers/leds/leds-lp5523.c
+++ b/drivers/leds/leds-lp5523.c
@@ -248,7 +248,10 @@ static int lp5523_configure(struct i2c_client *client)
/* Let the programs run for couple of ms and check the engine status */
usleep_range(3000, 6000);
- lp5523_read(client, LP5523_REG_STATUS, &status);
+ ret = lp5523_read(client, LP5523_REG_STATUS, &status);
+ if (ret < 0)
+ return ret;
+
status &= LP5523_ENG_STATUS_MASK;
if (status == LP5523_ENG_STATUS_MASK) {
@@ -464,10 +467,16 @@ static ssize_t lp5523_selftest(struct device *dev,
LP5523_EN_LEDTEST | 16);
usleep_range(3000, 6000); /* ADC conversion time is typically 2.7 ms */
ret = lp5523_read(chip->client, LP5523_REG_STATUS, &status);
+ if (ret < 0)
+ goto fail;
+
if (!(status & LP5523_LEDTEST_DONE))
usleep_range(3000, 6000); /* Was not ready. Wait little bit */
- ret |= lp5523_read(chip->client, LP5523_REG_LED_TEST_ADC, &vdd);
+ ret = lp5523_read(chip->client, LP5523_REG_LED_TEST_ADC, &vdd);
+ if (ret < 0)
+ goto fail;
+
vdd--; /* There may be some fluctuation in measurement */
for (i = 0; i < LP5523_LEDS; i++) {
@@ -489,9 +498,14 @@ static ssize_t lp5523_selftest(struct device *dev,
/* ADC conversion time is 2.7 ms typically */
usleep_range(3000, 6000);
ret = lp5523_read(chip->client, LP5523_REG_STATUS, &status);
+ if (ret < 0)
+ goto fail;
+
if (!(status & LP5523_LEDTEST_DONE))
usleep_range(3000, 6000);/* Was not ready. Wait. */
- ret |= lp5523_read(chip->client, LP5523_REG_LED_TEST_ADC, &adc);
+ ret = lp5523_read(chip->client, LP5523_REG_LED_TEST_ADC, &adc);
+ if (ret < 0)
+ goto fail;
if (adc >= vdd || adc < LP5523_ADC_SHORTCIRC_LIM)
pos += sprintf(buf + pos, "LED %d FAIL\n", i);
--
1.7.1
--
To unsubscribe from this list: send the line "unsubscribe linux-leds" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
