i find if my microsoft usb mouse is detected first, the glidepoint
device can not be detected,
but i cannot make sure, because i have not check all the cannot dmesg.
my machine : Dell D610
Linux localhost.localdomain 2.6.29.4-167.fc11.i586 #1 SMP Wed May 27
17:14:37 EDT 2009 i686 i686 i386 GNU/Linux
this is the diff file for can and cannot dmesg.
diff --git a/failure_dmesg.txt b/success_dmesg.txt
index 871bcd9..e9d6327 100644
--- a/failure_dmesg.txt
+++ b/success_dmesg.txt
@@ -103,7 +103,7 @@ Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Fast TSC calibration using PIT
-Detected 1994.855 MHz processor.
+Detected 1995.118 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
@@ -121,7 +121,7 @@ virtual kernel memory layout:
.text : 0xc0400000 - 0xc070be4a (3119 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
-Calibrating delay loop (skipped), value calculated using timer
frequency.. 3989.71 BogoMIPS (lpj=1994855)
+Calibrating delay loop (skipped), value calculated using timer
frequency.. 3990.23 BogoMIPS (lpj=1995118)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
@@ -144,7 +144,7 @@ ftrace: allocating 18115 entries in 72 pages
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Pentium(R) M processor 2.00GHz stepping 08
Brought up 1 CPUs
-Total of 1 processors activated (3989.71 BogoMIPS).
+Total of 1 processors activated (3990.23 BogoMIPS).
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=340 bytes
@@ -157,7 +157,7 @@ CPU0 attaching NULL sched-domain.
net_namespace: 1064 bytes
Booting paravirtualized kernel on bare hardware
regulator: core version 0.5
-Time: 0:04:34 Date: 07/12/09
+Time: 0:08:37 Date: 07/12/09
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
@@ -460,7 +460,7 @@ checking if image is initramfs... it is
Freeing initrd memory: 3056k freed
apm: BIOS not found.
audit: initializing netlink socket (disabled)
-type=2000 audit(1247357073.522:1): initialized
+type=2000 audit(1247357316.522:1): initialized
highmem bounce pool size: 64 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
@@ -496,7 +496,7 @@ ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
-ACPI: Thermal Zone [THM] (41 C)
+ACPI: Thermal Zone [THM] (60 C)
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
@@ -645,7 +645,7 @@ Initializing XFRM netlink socket
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
- Magic number: 1:416:51
+ Magic number: 1:966:101
Initalizing network drop monitor service
Freeing unused kernel memory: 424k freed
Write protecting the kernel read-only data: 1448k
@@ -659,7 +659,7 @@ ACPI: Video Device [VID2] (multi-head: yes rom:
no post: no)
[drm] Initialized drm 1.1.0 20060810
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
-Clocksource tsc unstable (delta = -73941129 ns)
+Clocksource tsc unstable (delta = -72576178 ns)
integrated sync not supported
usb 4-1: new low speed USB device using uhci_hcd and address 2
usb 4-1: New USB device found, idVendor=045e, idProduct=00cb
@@ -667,8 +667,10 @@ usb 4-1: New USB device strings: Mfr=1,
Product=2, SerialNumber=0
usb 4-1: Product: Microsoft Basic Optical Mouse v2.0
usb 4-1: Manufacturer: Microsoft
usb 4-1: configuration #1 chosen from 1 choice
-input: Microsoft Microsoft Basic Optical Mouse v2.0 as
/devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.0/input/input7
+input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input7
+input: Microsoft Microsoft Basic Optical Mouse v2.0 as
/devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.0/input/input8
generic-usb 0003:045E:00CB.0001: input,hidraw0: USB HID v1.11 Mouse
[Microsoft Microsoft Basic Optical Mouse v2.0 ] on
usb-0000:00:1d.2-1/input0
+input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input9
i2c-adapter i2c-0: unable to read EDID block.
i915 0000:00:02.0: VGA-1: no EDID data
integrated sync not supported
@@ -684,50 +686,47 @@ kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
-type=1404 audit(1247357078.235:2): selinux=0 auid=4294967295 ses=4294967295
+type=1404 audit(1247357321.311:2): selinux=0 auid=4294967295 ses=4294967295
udev: starting version 141
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
-input: PC Speaker as /devices/platform/pcspkr/input/input8
-parport_pc 00:0c: reported by Plug and Play ACPI
-parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
-ieee80211: 802.11 data/management/control stack, git-1.1.13
-ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@xxxxxxxxxxxxxxx>
-ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
-ipw2200: Copyright(c) 2003-2006 Intel Corporation
-ipw2200 0000:03:03.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
-ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection
-eth0 (ipw2200): not using net_device_ops yet
-ipw2200 0000:03:03.0: firmware: requesting ipw2200-bss.fw
-i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
+parport_pc 00:0c: reported by Plug and Play ACPI
+parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
+input: PC Speaker as /devices/platform/pcspkr/input/input10
+intel_rng: FWH not detected
tg3.c:v3.97 (December 10, 2008)
tg3 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
tg3 0000:02:00.0: setting latency timer to 64
tg3 0000:02:00.0: wake-up capability disabled by ACPI
tg3 0000:02:00.0: PME# disabled
-ipw2200: Detected geography ZZJ (14 802.11bg channels, 4 802.11a channels)
-eth1: Tigon3 [partno(BCM95751) rev 4001] (PCI Express) MAC address
00:14:22:b4:73:4b
-eth1: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1])
-eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
-eth1: dma_rwctrl[76180000] dma_mask[64-bit]
-udev: renamed network interface eth0 to eth1
-udev: renamed network interface eth1_rename to eth0
-intel_rng: FWH not detected
-yenta_cardbus 0000:03:01.0: CardBus bridge found [1028:0182]
-yenta_cardbus 0000:03:01.0: Using CSCINT to route CSC interrupts to PCI
-yenta_cardbus 0000:03:01.0: Routing CardBus interrupts to PCI
-yenta_cardbus 0000:03:01.0: TI: mfunc 0x01111122, devctl 0x64
+eth0: Tigon3 [partno(BCM95751) rev 4001] (PCI Express) MAC address
00:14:22:b4:73:4b
+eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1])
+eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
+eth0: dma_rwctrl[76180000] dma_mask[64-bit]
iTCO_vendor_support: vendor-support=0
+ppdev: user-space parallel port driver
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
-ppdev: user-space parallel port driver
+ieee80211: 802.11 data/management/control stack, git-1.1.13
+ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@xxxxxxxxxxxxxxx>
+yenta_cardbus 0000:03:01.0: CardBus bridge found [1028:0182]
+yenta_cardbus 0000:03:01.0: Using CSCINT to route CSC interrupts to PCI
+yenta_cardbus 0000:03:01.0: Routing CardBus interrupts to PCI
+yenta_cardbus 0000:03:01.0: TI: mfunc 0x01111122, devctl 0x64
+ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
+ipw2200: Copyright(c) 2003-2006 Intel Corporation
+i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
yenta_cardbus 0000:03:01.0: ISA IRQ mask 0x0c78, PCI irq 19
yenta_cardbus 0000:03:01.0: Socket status: 30000006
pci_bus 0000:03: Raising subordinate bus# of parent bus (#03) from #04 to #07
yenta_cardbus 0000:03:01.0: pcmcia: parent PCI bridge Memory window:
0xdfc00000 - 0xdfcfffff
yenta_cardbus 0000:03:01.0: pcmcia: parent PCI bridge Memory window:
0x60000000 - 0x63ffffff
+ipw2200 0000:03:03.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
+ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection
+eth1 (ipw2200): not using net_device_ops yet
+ipw2200 0000:03:03.0: firmware: requesting ipw2200-bss.fw
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
@@ -738,7 +737,8 @@ Intel ICH Modem 0000:00:1e.3: setting latency timer to 64
ALSA sound/pci/ac97/ac97_codec.c:2159: MC'97 1 converters and GPIO
not ready (0xff00)
Intel ICH 0000:00:1e.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Intel ICH 0000:00:1e.2: setting latency timer to 64
-intel8x0_measure_ac97_clock: measured 50777 usecs
+ipw2200: Detected geography ZZJ (14 802.11bg channels, 4 802.11a channels)
+intel8x0_measure_ac97_clock: measured 50774 usecs
intel8x0: clocking to 48000
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on sda3, internal journal
@@ -760,10 +760,10 @@ tg3 0000:02:00.0: PME# disabled
ADDRCONF(NETDEV_UP): eth0: link is not ready
Bridge firewalling registered
virbr0: starting userspace STP failed, starting kernel STP
-lo: Disabled Privacy Extensions
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
+lo: Disabled Privacy Extensions
i2c-adapter i2c-0: unable to read EDID block.
i915 0000:00:02.0: VGA-1: no EDID data
i2c-adapter i2c-0: unable to read EDID block.
@@ -787,12 +787,13 @@ integrated sync not supported
[drm] TV-15: set mode NTSC 480i 0
[drm] TV-15: set mode NTSC 480i 0
i2c-adapter i2c-0: unable to read EDID block.
-virbr0: no IPv6 routers present
i915 0000:00:02.0: VGA-1: no EDID data
i2c-adapter i2c-0: unable to read EDID block.
i915 0000:00:02.0: VGA-1: no EDID data
+eth0: no IPv6 routers present
integrated sync not supported
[drm] TV-15: set mode NTSC 480i 0
+virbr0: no IPv6 routers present
[drm] TV-15: set mode NTSC 480i 0
i2c-adapter i2c-0: unable to read EDID block.
i915 0000:00:02.0: VGA-1: no EDID data
@@ -801,7 +802,6 @@ i915 0000:00:02.0: VGA-1: no EDID data
integrated sync not supported
[drm] TV-15: set mode NTSC 480i 0
[drm] TV-15: set mode NTSC 480i 0
-eth0: no IPv6 routers present
i2c-adapter i2c-0: unable to read EDID block.
i915 0000:00:02.0: VGA-1: no EDID data
i2c-adapter i2c-0: unable to read EDID block.
--
To unsubscribe from this list: send the line "unsubscribe linux-laptop" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
