Instead of having a suite of dedicated cleanup functions, use the defer
framework to schedule cleanups right as their setup functions are run.
Signed-off-by: Petr Machata <petrm@xxxxxxxxxx>
---
.../drivers/net/mlxsw/sch_red_core.sh | 171 +++++++++---------
.../drivers/net/mlxsw/sch_red_ets.sh | 24 +--
.../drivers/net/mlxsw/sch_red_root.sh | 18 +-
.../selftests/net/forwarding/sch_red.sh | 103 ++++-------
4 files changed, 141 insertions(+), 175 deletions(-)
diff --git a/tools/testing/selftests/drivers/net/mlxsw/sch_red_core.sh b/tools/testing/selftests/drivers/net/mlxsw/sch_red_core.sh
index f4c324957dcc..4282142c8eca 100644
--- a/tools/testing/selftests/drivers/net/mlxsw/sch_red_core.sh
+++ b/tools/testing/selftests/drivers/net/mlxsw/sch_red_core.sh
@@ -89,39 +89,31 @@ host_create()
local host=$1; shift
simple_if_init $dev
+ defer simple_if_fini $dev
+
mtu_set $dev 10000
+ defer mtu_restore $dev
vlan_create $dev 10 v$dev $(ipaddr $host 10)/28
+ defer vlan_destroy $dev 10
ip link set dev $dev.10 type vlan egress 0:0
vlan_create $dev 11 v$dev $(ipaddr $host 11)/28
+ defer vlan_destroy $dev 11
ip link set dev $dev.11 type vlan egress 0:1
}
-host_destroy()
-{
- local dev=$1; shift
-
- vlan_destroy $dev 11
- vlan_destroy $dev 10
- mtu_restore $dev
- simple_if_fini $dev
-}
-
h1_create()
{
host_create $h1 1
}
-h1_destroy()
-{
- host_destroy $h1
-}
-
h2_create()
{
host_create $h2 2
+
tc qdisc add dev $h2 clsact
+ defer tc qdisc del dev $h2 clsact
# Some of the tests in this suite use multicast traffic. As this traffic
# enters BR2_10 resp. BR2_11, it is flooded to all other ports. Thus
@@ -139,13 +131,7 @@ h2_create()
tc qdisc replace dev $h2 root handle 10: tbf rate 200mbit \
burst 128K limit 1G
-}
-
-h2_destroy()
-{
- tc qdisc del dev $h2 root handle 10:
- tc qdisc del dev $h2 clsact
- host_destroy $h2
+ defer tc qdisc del dev $h2 root handle 10:
}
h3_create()
@@ -153,40 +139,54 @@ h3_create()
host_create $h3 3
}
-h3_destroy()
-{
- host_destroy $h3
-}
-
switch_create()
{
local intf
local vlan
ip link add dev br1_10 type bridge
+ defer ip link del dev br1_10
+
ip link add dev br1_11 type bridge
+ defer ip link del dev br1_11
ip link add dev br2_10 type bridge
+ defer ip link del dev br2_10
+
ip link add dev br2_11 type bridge
+ defer ip link del dev br2_11
for intf in $swp1 $swp2 $swp3 $swp4 $swp5; do
ip link set dev $intf up
+ defer ip link set dev $intf down
+
mtu_set $intf 10000
+ defer mtu_restore $intf
done
for intf in $swp1 $swp4; do
for vlan in 10 11; do
vlan_create $intf $vlan
+ defer vlan_destroy $intf $vlan
+
ip link set dev $intf.$vlan master br1_$vlan
+ defer ip link set dev $intf.$vlan nomaster
+
ip link set dev $intf.$vlan up
+ defer ip link set dev $intf.$vlan up
done
done
for intf in $swp2 $swp3 $swp5; do
for vlan in 10 11; do
vlan_create $intf $vlan
+ defer vlan_destroy $intf $vlan
+
ip link set dev $intf.$vlan master br2_$vlan
+ defer ip link set dev $intf.$vlan nomaster
+
ip link set dev $intf.$vlan up
+ defer ip link set dev $intf.$vlan up
done
done
@@ -201,49 +201,25 @@ switch_create()
for intf in $swp3 $swp4; do
tc qdisc replace dev $intf root handle 1: tbf rate 200mbit \
burst 128K limit 1G
+ defer tc qdisc del dev $intf root handle 1:
done
ip link set dev br1_10 up
+ defer ip link set dev br1_10 down
+
ip link set dev br1_11 up
+ defer ip link set dev br1_11 down
+
ip link set dev br2_10 up
+ defer ip link set dev br2_10 down
+
ip link set dev br2_11 up
+ defer ip link set dev br2_11 down
local size=$(devlink_pool_size_thtype 0 | cut -d' ' -f 1)
devlink_port_pool_th_save $swp3 8
devlink_port_pool_th_set $swp3 8 $size
-}
-
-switch_destroy()
-{
- local intf
- local vlan
-
- devlink_port_pool_th_restore $swp3 8
-
- ip link set dev br2_11 down
- ip link set dev br2_10 down
- ip link set dev br1_11 down
- ip link set dev br1_10 down
-
- for intf in $swp4 $swp3; do
- tc qdisc del dev $intf root handle 1:
- done
-
- for intf in $swp5 $swp3 $swp2 $swp4 $swp1; do
- for vlan in 11 10; do
- ip link set dev $intf.$vlan down
- ip link set dev $intf.$vlan nomaster
- vlan_destroy $intf $vlan
- done
-
- mtu_restore $intf
- ip link set dev $intf down
- done
-
- ip link del dev br2_11
- ip link del dev br2_10
- ip link del dev br1_11
- ip link del dev br1_10
+ defer devlink_port_pool_th_restore $swp3 8
}
setup_prepare()
@@ -263,6 +239,7 @@ setup_prepare()
h3_mac=$(mac_get $h3)
vrf_prepare
+ defer vrf_cleanup
h1_create
h2_create
@@ -270,18 +247,6 @@ setup_prepare()
switch_create
}
-cleanup()
-{
- pre_cleanup
-
- switch_destroy
- h3_destroy
- h2_destroy
- h1_destroy
-
- vrf_cleanup
-}
-
ping_ipv4()
{
ping_test $h1.10 $(ipaddr 3 10) " from host 1, vlan 10"
@@ -450,6 +415,7 @@ __do_ecn_test()
start_tcp_traffic $h1.$vlan $(ipaddr 1 $vlan) $(ipaddr 3 $vlan) \
$h3_mac tos=0x01
+ defer stop_traffic $!
sleep 1
ecn_test_common "$name" "$get_nmarked" $vlan $limit
@@ -462,7 +428,6 @@ __do_ecn_test()
check_fail $? "UDP traffic went into backlog instead of being early-dropped"
log_test "TC $((vlan - 10)): $name backlog > limit: UDP early-dropped"
- stop_traffic
sleep 1
}
@@ -471,7 +436,8 @@ do_ecn_test()
local vlan=$1; shift
local limit=$1; shift
- __do_ecn_test get_nmarked "$vlan" "$limit"
+ in_defer_scope \
+ __do_ecn_test get_nmarked "$vlan" "$limit"
}
do_ecn_test_perband()
@@ -480,10 +446,11 @@ do_ecn_test_perband()
local limit=$1; shift
mlxsw_only_on_spectrum 3+ || return
- __do_ecn_test get_qdisc_nmarked "$vlan" "$limit" "per-band ECN"
+ in_defer_scope \
+ __do_ecn_test get_qdisc_nmarked "$vlan" "$limit" "per-band ECN"
}
-do_ecn_nodrop_test()
+__do_ecn_nodrop_test()
{
local vlan=$1; shift
local limit=$1; shift
@@ -491,6 +458,7 @@ do_ecn_nodrop_test()
start_tcp_traffic $h1.$vlan $(ipaddr 1 $vlan) $(ipaddr 3 $vlan) \
$h3_mac tos=0x01
+ defer stop_traffic $!
sleep 1
ecn_test_common "$name" get_nmarked $vlan $limit
@@ -503,11 +471,16 @@ do_ecn_nodrop_test()
check_err $? "UDP traffic was early-dropped instead of getting into backlog"
log_test "TC $((vlan - 10)): $name backlog > limit: UDP not dropped"
- stop_traffic
sleep 1
}
-do_red_test()
+do_ecn_nodrop_test()
+{
+ in_defer_scope \
+ __do_ecn_nodrop_test "$@"
+}
+
+__do_red_test()
{
local vlan=$1; shift
local limit=$1; shift
@@ -518,6 +491,7 @@ do_red_test()
# is above limit.
start_tcp_traffic $h1.$vlan $(ipaddr 1 $vlan) $(ipaddr 3 $vlan) \
$h3_mac tos=0x01
+ defer stop_traffic $!
# Pushing below the queue limit should work.
RET=0
@@ -540,11 +514,16 @@ do_red_test()
check_err $? "backlog $backlog / $limit expected <= 15% distance"
log_test "TC $((vlan - 10)): RED backlog > limit"
- stop_traffic
sleep 1
}
-do_mc_backlog_test()
+do_red_test()
+{
+ in_defer_scope \
+ __do_red_test "$@"
+}
+
+__do_mc_backlog_test()
{
local vlan=$1; shift
local limit=$1; shift
@@ -554,7 +533,10 @@ do_mc_backlog_test()
RET=0
start_tcp_traffic $h1.$vlan $(ipaddr 1 $vlan) $(ipaddr 3 $vlan) bc
+ defer stop_traffic $!
+
start_tcp_traffic $h2.$vlan $(ipaddr 2 $vlan) $(ipaddr 3 $vlan) bc
+ defer stop_traffic $!
qbl=$(busywait 5000 until_counter_is ">= 500000" \
get_qdisc_backlog $vlan)
@@ -567,13 +549,16 @@ do_mc_backlog_test()
get_mc_transmit_queue $vlan)
check_err $? "MC backlog reported by qdisc not visible in ethtool"
- stop_traffic
- stop_traffic
-
log_test "TC $((vlan - 10)): Qdisc reports MC backlog"
}
-do_mark_test()
+do_mc_backlog_test()
+{
+ in_defer_scope \
+ __do_mc_backlog_test "$@"
+}
+
+__do_mark_test()
{
local vlan=$1; shift
local limit=$1; shift
@@ -588,6 +573,7 @@ do_mark_test()
start_tcp_traffic $h1.$vlan $(ipaddr 1 $vlan) $(ipaddr 3 $vlan) \
$h3_mac tos=0x01
+ defer stop_traffic $!
# Create a bit of a backlog and observe no mirroring due to marks.
qevent_rule_install_$subtest
@@ -618,11 +604,16 @@ do_mark_test()
log_test "TC $((vlan - 10)): marked packets $subtest'd"
fi
- stop_traffic
sleep 1
}
-do_drop_test()
+do_mark_test()
+{
+ in_defer_scope \
+ __do_mark_test "$@"
+}
+
+__do_drop_test()
{
local vlan=$1; shift
local limit=$1; shift
@@ -637,6 +628,7 @@ do_drop_test()
RET=0
start_traffic $h1.$vlan $(ipaddr 1 $vlan) $(ipaddr 3 $vlan) $h3_mac
+ defer stop_traffic $!
# Create a bit of a backlog and observe no mirroring due to drops.
qevent_rule_install_$subtest
@@ -672,10 +664,15 @@ do_drop_test()
log_test "TC $((vlan - 10)): ${trigger}ped packets $subtest'd"
- stop_traffic
sleep 1
}
+do_drop_test()
+{
+ in_defer_scope \
+ __do_drop_test "$@"
+}
+
qevent_rule_install_mirror()
{
tc filter add block 10 pref 1234 handle 102 matchall skip_sw \
diff --git a/tools/testing/selftests/drivers/net/mlxsw/sch_red_ets.sh b/tools/testing/selftests/drivers/net/mlxsw/sch_red_ets.sh
index 576067b207a8..8902a115d9cd 100755
--- a/tools/testing/selftests/drivers/net/mlxsw/sch_red_ets.sh
+++ b/tools/testing/selftests/drivers/net/mlxsw/sch_red_ets.sh
@@ -80,36 +80,34 @@ uninstall_qdisc()
ecn_test()
{
install_qdisc ecn
+ defer uninstall_qdisc
do_ecn_test 10 $BACKLOG1
do_ecn_test 11 $BACKLOG2
-
- uninstall_qdisc
}
ecn_test_perband()
{
install_qdisc ecn
+ defer uninstall_qdisc
do_ecn_test_perband 10 $BACKLOG1
do_ecn_test_perband 11 $BACKLOG2
-
- uninstall_qdisc
}
ecn_nodrop_test()
{
install_qdisc ecn nodrop
+ defer uninstall_qdisc
do_ecn_nodrop_test 10 $BACKLOG1
do_ecn_nodrop_test 11 $BACKLOG2
-
- uninstall_qdisc
}
red_test()
{
install_qdisc
+ defer uninstall_qdisc
# Make sure that we get the non-zero value if there is any.
local cur=$(busywait 1100 until_counter_is "> 0" \
@@ -120,50 +118,44 @@ red_test()
do_red_test 10 $BACKLOG1
do_red_test 11 $BACKLOG2
-
- uninstall_qdisc
}
mc_backlog_test()
{
install_qdisc
+ defer uninstall_qdisc
# Note that the backlog numbers here do not correspond to RED
# configuration, but are arbitrary.
do_mc_backlog_test 10 $BACKLOG1
do_mc_backlog_test 11 $BACKLOG2
-
- uninstall_qdisc
}
red_mirror_test()
{
install_qdisc qevent early_drop block 10
+ defer uninstall_qdisc
do_drop_mirror_test 10 $BACKLOG1 early_drop
do_drop_mirror_test 11 $BACKLOG2 early_drop
-
- uninstall_qdisc
}
red_trap_test()
{
install_qdisc qevent early_drop block 10
+ defer uninstall_qdisc
do_drop_trap_test 10 $BACKLOG1 early_drop
do_drop_trap_test 11 $BACKLOG2 early_drop
-
- uninstall_qdisc
}
ecn_mirror_test()
{
install_qdisc ecn qevent mark block 10
+ defer uninstall_qdisc
do_mark_mirror_test 10 $BACKLOG1
do_mark_mirror_test 11 $BACKLOG2
-
- uninstall_qdisc
}
bail_on_lldpad "configure DCB" "configure Qdiscs"
diff --git a/tools/testing/selftests/drivers/net/mlxsw/sch_red_root.sh b/tools/testing/selftests/drivers/net/mlxsw/sch_red_root.sh
index 159108d02895..e9043771787b 100755
--- a/tools/testing/selftests/drivers/net/mlxsw/sch_red_root.sh
+++ b/tools/testing/selftests/drivers/net/mlxsw/sch_red_root.sh
@@ -32,45 +32,51 @@ uninstall_qdisc()
ecn_test()
{
install_qdisc ecn
+ defer uninstall_qdisc
+
do_ecn_test 10 $BACKLOG
- uninstall_qdisc
}
ecn_test_perband()
{
install_qdisc ecn
+ defer uninstall_qdisc
+
do_ecn_test_perband 10 $BACKLOG
- uninstall_qdisc
}
ecn_nodrop_test()
{
install_qdisc ecn nodrop
+ defer uninstall_qdisc
+
do_ecn_nodrop_test 10 $BACKLOG
- uninstall_qdisc
}
red_test()
{
install_qdisc
+ defer uninstall_qdisc
+
do_red_test 10 $BACKLOG
- uninstall_qdisc
}
mc_backlog_test()
{
install_qdisc
+ defer uninstall_qdisc
+
# Note that the backlog value here does not correspond to RED
# configuration, but is arbitrary.
do_mc_backlog_test 10 $BACKLOG
- uninstall_qdisc
}
red_mirror_test()
{
install_qdisc qevent early_drop block 10
+ defer uninstall_qdisc
+
do_drop_mirror_test 10 $BACKLOG
- uninstall_qdisc
}
bail_on_lldpad "configure DCB" "configure Qdiscs"
diff --git a/tools/testing/selftests/net/forwarding/sch_red.sh b/tools/testing/selftests/net/forwarding/sch_red.sh
index 17f28644568e..af166662b78a 100755
--- a/tools/testing/selftests/net/forwarding/sch_red.sh
+++ b/tools/testing/selftests/net/forwarding/sch_red.sh
@@ -53,71 +53,63 @@ PKTSZ=1400
h1_create()
{
simple_if_init $h1 192.0.2.1/28
+ defer simple_if_fini $h1 192.0.2.1/28
+
mtu_set $h1 10000
+ defer mtu_restore $h1
+
tc qdisc replace dev $h1 root handle 1: tbf \
rate 10Mbit burst 10K limit 1M
-}
-
-h1_destroy()
-{
- tc qdisc del dev $h1 root
- mtu_restore $h1
- simple_if_fini $h1 192.0.2.1/28
+ defer tc qdisc del dev $h1 root
}
h2_create()
{
simple_if_init $h2 192.0.2.2/28
+ defer simple_if_fini $h2 192.0.2.2/28
+
mtu_set $h2 10000
-}
-
-h2_destroy()
-{
- mtu_restore $h2
- simple_if_fini $h2 192.0.2.2/28
+ defer mtu_restore $h2
}
h3_create()
{
simple_if_init $h3 192.0.2.3/28
+ defer simple_if_fini $h3 192.0.2.3/28
+
mtu_set $h3 10000
-}
-
-h3_destroy()
-{
- mtu_restore $h3
- simple_if_fini $h3 192.0.2.3/28
+ defer mtu_restore $h3
}
switch_create()
{
ip link add dev br up type bridge
+ defer ip link del dev br
+
ip link set dev $swp1 up master br
+ defer ip link set dev $swp1 down nomaster
+
ip link set dev $swp2 up master br
+ defer ip link set dev $swp2 down nomaster
+
ip link set dev $swp3 up master br
+ defer ip link set dev $swp3 down nomaster
mtu_set $swp1 10000
+ defer mtu_restore $h1
+
mtu_set $swp2 10000
+ defer mtu_restore $h2
+
mtu_set $swp3 10000
+ defer mtu_restore $h3
tc qdisc replace dev $swp3 root handle 1: tbf \
rate 10Mbit burst 10K limit 1M
+ defer tc qdisc del dev $swp3 root
+
ip link add name _drop_test up type dummy
-}
-
-switch_destroy()
-{
- ip link del dev _drop_test
- tc qdisc del dev $swp3 root
-
- mtu_restore $h3
- mtu_restore $h2
- mtu_restore $h1
-
- ip link set dev $swp3 down nomaster
- ip link set dev $swp2 down nomaster
- ip link set dev $swp1 down nomaster
- ip link del dev br
+ defer ip link del dev _drop_test
}
setup_prepare()
@@ -134,6 +126,7 @@ setup_prepare()
h3_mac=$(mac_get $h3)
vrf_prepare
+ defer vrf_cleanup
h1_create
h2_create
@@ -141,18 +134,6 @@ setup_prepare()
switch_create
}
-cleanup()
-{
- pre_cleanup
-
- switch_destroy
- h3_destroy
- h2_destroy
- h1_destroy
-
- vrf_cleanup
-}
-
ping_ipv4()
{
ping_test $h1 192.0.2.3 " from host 1"
@@ -287,6 +268,7 @@ do_ecn_test()
$MZ $h1 -p $PKTSZ -A 192.0.2.1 -B 192.0.2.3 -c 0 \
-a own -b $h3_mac -t tcp -q tos=0x01 &
+ defer stop_traffic $!
sleep 1
ecn_test_common "$name" $limit
@@ -298,9 +280,6 @@ do_ecn_test()
build_backlog $((2 * limit)) udp >/dev/null
check_fail $? "UDP traffic went into backlog instead of being early-dropped"
log_test "$name backlog > limit: UDP early-dropped"
-
- stop_traffic
- sleep 1
}
do_ecn_nodrop_test()
@@ -310,6 +289,7 @@ do_ecn_nodrop_test()
$MZ $h1 -p $PKTSZ -A 192.0.2.1 -B 192.0.2.3 -c 0 \
-a own -b $h3_mac -t tcp -q tos=0x01 &
+ defer stop_traffic $!
sleep 1
ecn_test_common "$name" $limit
@@ -321,9 +301,6 @@ do_ecn_nodrop_test()
build_backlog $((2 * limit)) udp >/dev/null
check_err $? "UDP traffic was early-dropped instead of getting into backlog"
log_test "$name backlog > limit: UDP not dropped"
-
- stop_traffic
- sleep 1
}
do_red_test()
@@ -336,6 +313,7 @@ do_red_test()
# is above limit.
$MZ $h1 -p $PKTSZ -A 192.0.2.1 -B 192.0.2.3 -c 0 \
-a own -b $h3_mac -t tcp -q tos=0x01 &
+ defer stop_traffic $!
# Pushing below the queue limit should work.
RET=0
@@ -352,9 +330,6 @@ do_red_test()
pct=$(check_marking "== 0")
check_err $? "backlog $backlog / $limit Got $pct% marked packets, expected == 0."
log_test "RED backlog > limit"
-
- stop_traffic
- sleep 1
}
do_red_qevent_test()
@@ -369,6 +344,7 @@ do_red_qevent_test()
$MZ $h1 -p $PKTSZ -A 192.0.2.1 -B 192.0.2.3 -c 0 \
-a own -b $h3_mac -t udp -q &
+ defer stop_traffic $!
sleep 1
tc filter add block 10 pref 1234 handle 102 matchall skip_hw \
@@ -396,9 +372,6 @@ do_red_qevent_test()
check_err $? "Dropped packets still observed: 0 expected, $((now - base)) seen"
log_test "RED early_dropped packets mirrored"
-
- stop_traffic
- sleep 1
}
do_ecn_qevent_test()
@@ -410,6 +383,7 @@ do_ecn_qevent_test()
$MZ $h1 -p $PKTSZ -A 192.0.2.1 -B 192.0.2.3 -c 0 \
-a own -b $h3_mac -t tcp -q tos=0x01 &
+ defer stop_traffic $!
sleep 1
tc filter add block 10 pref 1234 handle 102 matchall skip_hw \
@@ -428,9 +402,6 @@ do_ecn_qevent_test()
tc filter del block 10 pref 1234 handle 102 matchall
log_test "ECN marked packets mirrored"
-
- stop_traffic
- sleep 1
}
install_qdisc()
@@ -451,36 +422,36 @@ uninstall_qdisc()
ecn_test()
{
install_qdisc ecn
+ defer uninstall_qdisc
xfail_on_slow do_ecn_test $BACKLOG
- uninstall_qdisc
}
ecn_nodrop_test()
{
install_qdisc ecn nodrop
+ defer uninstall_qdisc
xfail_on_slow do_ecn_nodrop_test $BACKLOG
- uninstall_qdisc
}
red_test()
{
install_qdisc
+ defer uninstall_qdisc
xfail_on_slow do_red_test $BACKLOG
- uninstall_qdisc
}
red_qevent_test()
{
install_qdisc qevent early_drop block 10
+ defer uninstall_qdisc
xfail_on_slow do_red_qevent_test $BACKLOG
- uninstall_qdisc
}
ecn_qevent_test()
{
install_qdisc ecn qevent mark block 10
+ defer uninstall_qdisc
xfail_on_slow do_ecn_qevent_test $BACKLOG
- uninstall_qdisc
}
trap cleanup EXIT
--
2.45.0
