On 9/17/24 16:48, Yifei Liu wrote:
We recently notice that the step_after_suspend_test would
fail on our plenty devices. The test believesit failed to
What are "plenty devices"
recently noticed?
Typo - believesit?
enter suspend state with
$ sudo ./step_after_suspend_test
TAP version 13
Bail out! Failed to enter Suspend state
However, in the kernel message, I indeed see the system get
suspended and then wake up later.
[611172.033108] PM: suspend entry (s2idle)
[611172.044940] Filesystems sync: 0.006 seconds
[611172.052254] Freezing user space processes
[611172.059319] Freezing user space processes completed (elapsed 0.001 seconds)
[611172.067920] OOM killer disabled.
[611172.072465] Freezing remaining freezable tasks
[611172.080332] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
[611172.089724] printk: Suspending console(s) (use no_console_suspend to debug)
[611172.117126] serial 00:03: disabled
--- some other hardware get reconnected ---
[611203.136277] OOM killer enabled.
[611203.140637] Restarting tasks ...
[611203.141135] usb 1-8.1: USB disconnect, device number 7
[611203.141755] done.
[611203.155268] random: crng reseeded on system resumption
[611203.162059] PM: suspend exit
After investigation, I notice that for the code block
if (write(power_state_fd, "mem", strlen("mem")) != strlen("mem"))
ksft_exit_fail_msg("Failed to enter Suspend state\n");
The write will return -1 and errno is set to 16 (device busy).
It should be caused by the write function is not successfully returned
before the system suspend and the return value get messed when waking up.
As a result, It may be better to check the time passed of those few instructions
to determine whether the suspend is executed correctly for it is pretty hard to
execute those few lines for 4 seconds, or even more if it is not long enough.
I don't think this is the right fix. Can you change this to do echo instead.
It does the same thing, but it goes through sysfs interface instead of direct
write:
ret = system("echo mem > /sys/power/state");
Fixes: bfd092b8c2728 ("selftests: breakpoint: add step_after_suspend_test")
Reported-by: Sinadin Shan <sinadin.shan@xxxxxxxxxx>
Signed-off-by: Yifei Liu <yifei.l.liu@xxxxxxxxxx>
---
.../selftests/breakpoints/step_after_suspend_test.c | 9 +++++++--
1 file changed, 7 insertions(+), 2 deletions(-)
diff --git a/tools/testing/selftests/breakpoints/step_after_suspend_test.c b/tools/testing/selftests/breakpoints/step_after_suspend_test.c
index dfec31fb9b30d..d615f091e5bae 100644
--- a/tools/testing/selftests/breakpoints/step_after_suspend_test.c
+++ b/tools/testing/selftests/breakpoints/step_after_suspend_test.c
@@ -18,6 +18,7 @@
#include <sys/timerfd.h>
#include <sys/types.h>
#include <sys/wait.h>
+#include <time.h>
#include "../kselftest.h"
@@ -133,6 +134,7 @@ void suspend(void)
int timerfd;
int err;
struct itimerspec spec = {};
+ clock_t t;
if (getuid() != 0)
ksft_exit_skip("Please run the test as root - Exiting.\n");
@@ -152,8 +154,11 @@ void suspend(void)
if (err < 0)
ksft_exit_fail_msg("timerfd_settime() failed\n");
I don't think you will need to add clock() code. timerfd_settime()
sets the time for 5 seconds and you can simply extend the alarm
time.
There needs to be some logic to check timer elapse and poll the
timer_fd
- if (write(power_state_fd, "mem", strlen("mem")) != strlen("mem"))
- ksft_exit_fail_msg("Failed to enter Suspend state\n");
+ t = clock();
+ write(power_state_fd, "mem", strlen("mem"));
+ t = clock()-t;
+ if ((int)(t) < 4)
+ ksft_exit_fail_msg("Failed to enter Suspend state %d\n",errno);
close(timerfd);
close(power_state_fd);
thanks,
-- Shuah
