Re: [PATCH 2/2] selftests/nolibc: add testcase for pipe.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, Jul 30, 2023 at 08:55:47AM +0200, Thomas Weißschuh wrote:
> On 2023-07-30 05:33:43+0200, Willy Tarreau wrote:
> > On Sun, Jul 30, 2023 at 12:17:24AM +0200, Thomas Weißschuh wrote:
> > > > +	case 0:
> > > > +		close(pipefd[0]);
> > > > +		write(pipefd[1], msg, strlen(msg));
> > > 
> > > Isn't this missing to write trailing the 0 byte?
> > 
> > It depends if the other side expects to get the trailing 0.
> > In general it's better to avoid sending it since it's only
> > used for internal representation, and the other side must
> > be prepared to receive anything anyway.
> > 
> > > Also check the return value.
> > 
> > Indeed!
> > 
> > > > +		close(pipefd[1]);
> > > 
> > > Do we need to close the pipefds? The process is exiting anyways.
> > 
> > It's better to, because we could imagine looping over the tests for
> > example. Thus each test shoulld have as little impact as possible
> > on other tests.
> 
> I meant the newly forked child exiting, not nolibc-test in general.
> The exit is just below, so the fds in the child are close here anyways.

Ah OK, but still it remains cleaner with it IMHO (i.e. better rely on
explicit things in tests, that's less doubts when they fail).

> > > > +	default:
> > > > +		close(pipefd[1]);
> > > > +		read(pipefd[0], buf, 32);
> > > 
> > > Use sizeof(buf). Check return value == strlen(msg).
> > > 
> > > > +		close(pipefd[0]);
> > > > +		wait(NULL);
> > > 
> > > waitpid(pid, NULL, 0);
> > > 
> > > > +
> > > > +		if (strcmp(buf, msg))
> > > > +			return 1;
> > > > +		return 0;
> > > 
> > > return !!strcmp(buf, msg);
> > 
> > In fact before that we need to terminate the output buffer. If for any
> > reason the transfer fails (e.g. the syscall fails or transfers data at
> > another location or of another length, we could end up comparing past
> > the end of the buffer. Thus I suggest adding this immediately after the
> > read():
> > 
> > 		buf[sizeof(buf) - 1] = 0;
> 
> This would still access uninitialized memory and lead to UB in strcmp as
> not all bytes in buf were written to by read().
> 
> If we want to be really sure we should use memcmp() instead of strcmp().
> For memcmp() I would prefer to transfer and check without the '\0', so
> my review comments from before need to be adapted a bit.

In fact you make a good point regarding the fact that the test doesn't
use read()'s return value. This problem totally goes away if the return
value is used, e.g.:

      len = read(pipefd[0], buf, sizeof(buf));
      close(pipefd[0]);
      waitpid(pid, NULL, 0);
      return len < 0 || len > sizeof(buf) || len > strlen(msg) || memcmp(buf, msg, len) != 0;

Willy



[Index of Archives]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [Share Photos]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux