Re: [RFC PATCH 00/13] x86 User Interrupts support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 9/13/21 4:01 PM, Sohil Mehta wrote:
User Interrupts Introduction
============================

User Interrupts (Uintr) is a hardware technology that enables delivering
interrupts directly to user space.

Today, virtually all communication across privilege boundaries happens by going
through the kernel. These include signals, pipes, remote procedure calls and
hardware interrupt based notifications. User interrupts provide the foundation
for more efficient (low latency and low CPU utilization) versions of these
common operations by avoiding transitions through the kernel.

In the User Interrupts hardware architecture, a receiver is always expected to
be a user space task. However, a user interrupt can be sent by another user
space task, kernel or an external source (like a device).

In addition to the general infrastructure to receive user interrupts, this
series introduces a single source: interrupts from another user task.  These
are referred to as User IPIs.

The first implementation of User IPIs will be in the Intel processor code-named
Sapphire Rapids. Refer Chapter 11 of the Intel Architecture instruction set
extensions for details of the hardware architecture [1].

Series-reviewed-by: Tony Luck<tony.luck@xxxxxxxxx>

Main goals of this RFC
======================
- Introduce this upcoming technology to the community.
This cover letter includes a hardware architecture summary along with the
software architecture and kernel design choices. This post is a bit long as a
result. Hopefully, it helps answer more questions than it creates :) I am also
planning to talk about User Interrupts next week at the LPC Kernel summit.

- Discuss potential use cases.
We are starting to look at actual usages and libraries (like libevent[2] and
liburing[3]) that can take advantage of this technology. Unfortunately, we
don't have much to share on this right now. We need some help from the
community to identify usages that can benefit from this. We would like to make
sure the proposed APIs work for the eventual consumers.

- Get early feedback on the software architecture.
We are hoping to get some feedback on the direction of overall software
architecture - starting with User IPI, extending it for kernel-to-user
interrupt notifications and external interrupts in the future.

- Discuss some of the main architecture opens.
There is lot of work that still needs to happen to enable this technology. We
are looking for some input on future patches that would be of interest. Here
are some of the big opens that we are looking to resolve.
* Should Uintr interrupt all blocking system calls like sleep(), read(),
   poll(), etc? If so, should we implement an SA_RESTART type of mechanism
   similar to signals? - Refer Blocking for interrupts section below.

* Should the User Interrupt Target table (UITT) be shared between threads of a
   multi-threaded application or maybe even across processes? - Refer Sharing
   the UITT section below.

Why care about this? - Micro benchmark performance
==================================================
There is a ~9x or higher performance improvement using User IPI over other IPC
mechanisms for event signaling.

Below is the average normalized latency for a 1M ping-pong IPC notifications
with message size=1.

+------------+-------------------------+
| IPC type   |   Relative Latency      |
|            |(normalized to User IPI) |
+------------+-------------------------+
| User IPI   |                     1.0 |
| Signal     |                    14.8 |
| Eventfd    |                     9.7 |
| Pipe       |                    16.3 |
| Domain     |                    17.3 |
+------------+-------------------------+

Results have been estimated based on tests on internal hardware with Linux
v5.14 + User IPI patches.

Original benchmark:https://github.com/goldsborough/ipc-bench
Updated benchmark:https://github.com/intel/uintr-ipc-bench/tree/linux-rfc-v1

*Performance varies by use, configuration and other factors.

How it works underneath? - Hardware Summary
===========================================
User Interrupts is a posted interrupt delivery mechanism. The interrupts are
first posted to a memory location and then delivered to the receiver when they
are running with CPL=3.

Kernel managed architectural data structures
--------------------------------------------
UPID: User Posted Interrupt Descriptor - Holds receiver interrupt vector
information and notification state (like an ongoing notification, suppressed
notifications).

UITT: User Interrupt Target Table - Stores UPID pointer and vector information
for interrupt routing on the sender side. Referred by the senduipi instruction.

The interrupt state of each task is referenced via MSRs which are saved and
restored by the kernel during context switch.

Instructions
------------
senduipi <index> - send a user IPI to a target task based on the UITT index.

clui - Mask user interrupts by clearing UIF (User Interrupt Flag).

stui - Unmask user interrupts by setting UIF.

testui - Test current value of UIF.

uiret - return from a user interrupt handler.

User IPI
--------
When a User IPI sender executes 'senduipi <index>', the hardware refers the
UITT table entry pointed by the index and posts the interrupt vector (63-0)
into the receiver's UPID.

If the receiver is running (CPL=3), the sender cpu would send a physical IPI to
the receiver's cpu. On the receiver side this IPI is detected as a User
Interrupt. The User Interrupt handler for the receiver is invoked and the
vector number (63-0) is pushed onto the stack.

Upon execution of 'uiret' in the interrupt handler, the control is transferred
back to instruction that was interrupted.

Refer Chapter 11 of the Intel Architecture instruction set extensions [1] for
more details.

Application interface - Software Architecture
=============================================
User Interrupts (Uintr) is an opt-in feature (unlike signals). Applications
wanting to use Uintr are expected to register themselves with the kernel using
the Uintr related system calls. A Uintr receiver is always a userspace task. A
Uintr sender can be another userspace task, kernel or a device.

1) A receiver can register/unregister an interrupt handler using the Uintr
receiver related syscalls.
		uintr_register_handler(handler, flags)
		uintr_unregister_handler(flags)

2) A syscall also allows a receiver to register a vector and create a user
interrupt file descriptor - uintr_fd.
		uintr_fd = uintr_create_fd(vector, flags)

Uintr can be useful in some of the usages where eventfd or signals are used for
frequent userspace event notifications. The semantics of uintr_fd are somewhat
similar to an eventfd() or the write end of a pipe.

3) Any sender with access to uintr_fd can use it to deliver events (in this
case - interrupts) to a receiver. A sender task can manage its connection with
the receiver using the sender related syscalls based on uintr_fd.
		uipi_index = uintr_register_sender(uintr_fd, flags)

Using an FD abstraction provides a secure mechanism to connect with a receiver.
The FD sharing and isolation mechanisms put in place by the kernel would extend
to Uintr as well.

4a) After the initial setup, a sender task can use the SENDUIPI instruction
along with the uipi_index to generate user IPIs without any kernel
intervention.
		SENDUIPI <uipi_index>

If the receiver is running (CPL=3), then the user interrupt is delivered
directly without a kernel transition. If the receiver isn't running the
interrupt is delivered when the receiver gets context switched back. If the
receiver is blocked in the kernel, the user interrupt is delivered to the
kernel which then unblocks the intended receiver to deliver the interrupt.

4b) If the sender is the kernel or a device, the uintr_fd can be passed onto
the related kernel entity to allow them to setup a connection and then generate
a user interrupt for event delivery. <The exact details of this API are still
being worked upon.>

For details of the user interface and associated system calls refer the Uintr
man-pages draft:
https://github.com/intel/uintr-linux-kernel/tree/rfc-v1/tools/uintr/manpages.
We have also included the same content as patch 1 of this series to make it
easier to review.

Refer the Uintr compiler programming guide [4] for details on Uintr integration
with GCC and Binutils.

Kernel design choices
=====================
Here are some of the reasons and trade-offs for the current design of the APIs.

System call interface
---------------------
Why a system call interface?: The 2 options we considered are using a char
device at /dev or use system calls (current approach). A syscall approach
avoids exposing a core cpu feature through a driver model. Also, we want to
have a user interrupt FD per vector and share a single common interrupt handler
among all vectors. This seems easier for the kernel and userspace to accomplish
using a syscall based approach.

Data sharing using user interrupts: Uintr doesn't include a mechanism to
share/transmit data. The expectation is applications use existing data sharing
mechanisms to share data and use Uintr only for signaling.

An FD for each vector: A uintr_fd is assigned to each vector to allow fine
grained priority and event management by the receiver. The alternative we
considered was to allocate an FD to the interrupt handler and having that
shared with the sender. However, that approach relies on the sender selecting
the vector and moves the vector priority management to the sender. Also, if
multiple senders want to send unique user interrupts they would need to
coordinate the vector selection amongst them.

Extending the APIs: Currently, the system calls are only extendable using the
flags argument. We can add a variable size struct to some of the syscalls if
needed.

Extending existing mechanisms
-----------------------------
Uintr can be beneficial in some of the usages where eventfd() or signals are
used. Since Uintr is hardware-dependent, thread-specific and bypasses the
kernel in the fast path, it makes extending existing mechanisms harder.

Main issues with extending signals:
Signal handlers are defined significantly differently than a User interrupt
handler. An application needs to save/restore registers in a user interrupt
handler and call uiret to return from it. Also, signals can be process directed
(or thread directed) but user interrupts are always thread directed.

Comparison of signals with User Interrupts:
+=====================+===========================+===========================+
|                     | Signals                   | User Interrupts           |
+=====================+===========================+===========================+
| Stacks              | Has alt stacks            | Uses application stack    |
|                     |                           | (alternate stack option   |
|                     |                           | not yet enabled)          |
+---------------------+---------------------------+---------------------------+
| Registers state     | Kernel manages incl.      | App responsible (Use GCC  |
|                     | FPU/XSTATE area           | 'interrupt' attribute for |
|                     |                           | general purpose registers)|
+---------------------+---------------------------+---------------------------+
| Blocking/Masking    | sigprocmask(2)/sa_mask    | CLUI instruction (No per  |
|                     |                           | vector masking)           |
+---------------------+---------------------------+---------------------------+
| Direction           | Uni-directional           | Uni-directional           |
+---------------------+---------------------------+---------------------------+
| Post event          | kill(), signal(),         | SENDUIPI <index> - index  |
|                     | sigqueue(), etc.          | derived from uintr_fd     |
+---------------------+---------------------------+---------------------------+
| Target              | Process-directed or       | Thread-directed           |
|                     | thread-directed           |                           |
+---------------------+---------------------------+---------------------------+
| Fork/inheritance    | Empty signal set          | Nothing is inherited      |
+---------------------+---------------------------+---------------------------+
| Execv               | Pending signals preserved | Nothing is inherited      |
+---------------------+---------------------------+---------------------------+
| Order of delivery   | Undetermined              | High to low vector numbers|
| for multiple signals|                           |                           |
+---------------------+---------------------------+---------------------------+
| Handler re-entry    | All signals except the    | No interrupts can cause   |
|                     | one being handled         | handler re-entry.         |
+---------------------+---------------------------+---------------------------+
| Delivery feedback   | 0 or -1 based on whether  | No feedback on whether the|
|                     | the signal was sent       | interrupt was sent or     |
|                     |                           | received.                 |
+---------------------+---------------------------+---------------------------+

Main issues with extending eventfd():
eventfd() has a counter value that is core to the API. User interrupts can't
have an associated counter since the signaling happens at the user level and
the hardware doesn't have a memory counter mechanism. Also, eventfd can be used
for bi-directional signaling where as uintr_fd is uni-directional.

Comparison of eventfd with uintr_fd:
+====================+======================+==============================+
|                    | Eventfd              | uintr_fd (User Interrupt FD) |
+====================+======================+==============================+
| Object             | Counter - uint64     | Receiver vector information  |
+--------------------+----------------------+------------------------------+
| Post event         | write() to eventfd   | SENDUIPI <index> - index     |
|                    |                      | derived from uintr_fd        |
+--------------------+----------------------+------------------------------+
| Receive event      | read() on eventfd    | Implicit - Handler is        |
|                    |                      | invoked with associated      |
|                    |                      | vector.                      |
+--------------------+----------------------+------------------------------+
| Direction          | Bi-directional       | Uni-directional              |
+--------------------+----------------------+------------------------------+
| Data transmitted   | Counter - uint64     | None                         |
+--------------------+----------------------+------------------------------+
| Waiting for events | Poll() family of     | No per vector wait.          |
|                    | syscalls             | uintr_wait() allows waiting  |
|                    |                      | for all user interrupts      |
+--------------------+----------------------+------------------------------+

Security Model
==============
User Interrupts is designed as an opt-in feature (unlike signals). The security
model for user interrupts is intended to be similar to eventfd(). The general
idea is that any sender with access to uintr_fd would be able to generate the
associated interrupt vector for the receiver task that created the fd.

Untrusted processes
-------------------
The current implementation expects only trusted and cooperating processes to
communicate using user interrupts. Coordination is expected between processes
for a connection teardown. In situations where coordination doesn't happen
(say, due to abrupt process exit), the kernel would end up keeping shared
resources (like UPID) allocated to avoid faults.

Currently, a sender can easily cause a denial of service for the receiver by
generating a storm of user interrupts. A user interrupt handler is invoked with
interrupts disabled, but upon execution of uiret, interrupts get enabled again
by the hardware. This can lead to the handler being invoked again before normal
execution can resume. There isn't a hardware mechanism to mask specific
interrupt vectors.

To enable untrusted processes to communicate, we need to add a per-vector
masking option through another syscall (or maybe IOCTL). However, this can add
some complexity to the kernel code. A vector can only be masked by modifying
the UITT entries at the source. We need to be careful about races while
removing and restoring the UPID from the UITT.

Resource limits
---------------
The maximum number of receiver-sender connections would be limited by the
maximum number of open file descriptors and the size of the UITT.

The UITT size is chosen as 4kB fixed size arbitrarily right now. We plan to
make it dynamic and configurable in size. RLIMIT_MEMLOCK or ENOMEM should be
triggered when the size limits have been hit.

Main Opens
==========

Blocking for interrupts
-----------------------
User interrupts are delivered to applications immediately if they are running
in userspace. If a receiver task has blocked in the kernel using the placeholder
uintr_wait() syscall, the task would be woken up to deliver the user interrupt.
However, if the task is blocked due to any other blocking calls like read(),
sleep(), etc; the interrupt will only get delivered when the application gets
scheduled again. We need to consider if applications need to receive User
Interrupts as soon as they are posted (similar to signals) when they are
blocked due to some other reason. Adding this capability would likely make the
kernel implementation more complex.

Interrupting system calls using User Interrupts would also mean we need to
consider an SA_RESTART type of mechanism. We also need to evaluate if some of
the signal handler related semantics in the kernel can be reused for User
Interrupts.

Sharing the User Interrupt Target Table (UITT)
----------------------------------------------
The current implementation assigns a unique UITT to each task. This assumes
that User interrupts are used for point-to-point communication between 2 tasks.
Also, this keeps the kernel implementation relatively simple.

However, there are of benefits to sharing the UITT between threads of a
multi-threaded application. One, they would see a consistent view of the UITT.
i.e. SENDUIPI <index> would mean the same on all threads of the application.
Also, each thread doesn't have to register itself using the common uintr_fd.
This would simplify the userspace setup and make efficient use of kernel
memory. The potential downside is that the kernel implementation to allocate,
modify, expand and free the UITT would be more complex.

A similar argument can be made for a set of processes that do a lot of IPC
amongst them. They would prefer to have a shared UITT that lets them target any
process from any process. With the current file descriptor based approach, the
connection setup can be time consuming and somewhat cumbersome. We need to
evaluate if this can be made simpler as well.

Kernel page table isolation (KPTI)
----------------------------------
SENDUIPI is a special ring-3 instruction that makes a supervisor mode memory
access to the UPID and UITT memory. The current patches need KPTI to be
disabled for User IPIs to work. To make User IPI work with KPTI, we need to
allocate these structures from a special memory region that has supervisor
access but it is mapped into userspace. The plan is to implement a mechanism
similar to LDT.

Processors that support user interrupts are not affected by Meltdown so the
auto mode of KPTI will default to off. Users who want to force enable KPTI will
need to wait for a later version of this patch series to use user interrupts.
Please let us know if you want the development of these patches to be
prioritized (or deprioritized).

FAQs
====
Q: What happens if a process is "surprised" by a user interrupt?
A: For tasks that haven't registered with the kernel and requested for user
interrupts aren't expected or able to receive to user interrupts.

Q: Do user interrupts affect kernel scheduling?
A: No. If a task is blocked waiting for user interrupts, when the kernel
receives a notification on behalf of that task we only put it back on the
runqueue. Delivery of a user interrupt in no way changes the scheduling
priorities of a task.

Q: Does the sender get to know if the interrupt was delivered?
A: No. User interrupts only provides a posted interrupt delivery mechanism. If
applications need to rely on whether the interrupt was delivered they should
consider a userspace mechanism for feedback (like a shared memory counter or a
user interrupt back to the sender).

Q: Why is there no feedback on interrupt delivery?
A: Being a posted interrupt delivery mechanism, the interrupt delivery
happens in 2 steps:
1) The interrupt information is stored in a memory location (UPID).
2) The physical interrupt is delivered to the interrupt receiver.

The 2nd step could happen immediately, after an extended period, or it might
never happen based on the state of the receiver after step 1. (The receiver
could have disabled interrupts, have been context switched out or it might have
crashed during that time.) This makes it very hard for the hardware to reliably
provide feedback upon execution of SENDUIPI.

Q: Can user interrupts be nested?
A: Yes. Using STUI instruction in the interrupt handler would allow new user
interrupts to be delivered. However, there no TPR(thread priority register)
like mechanism to allow only higher priority interrupts. Any user interrupt can
be taken when nesting is enabled.

Q: Can a task receive all pending user interrupts in one go?
A: No. The hardware allows only one vector to be processed at a time. If a task
is interested in knowing all the interrupts that are pending then we could add
a syscall that provides the pending interrupts information.

Q: Do the processes need to be pinned to a cpu?
A: No. User interrupts will be routed correctly to whichever cpu the receiver
is running on. The kernel updates the cpu information in the UPID during
context switch.

Q: Why are UPID and UITT allocated by the kernel?
A: If allocated by user space, applications could misuse the UPID and UITT to
write to unauthorized memory and generate interrupts on any cpu. The UPID and
UITT are allocated by the kernel and accessed by the hardware with supervisor
privilege.

Patch structure for this series
===============================
- Man-pages and Kernel documentation (patch 1,2)
- Hardware enumeration (patch 3, 4)
- User IPI kernel vector reservation (patch 5)
- Syscall interface for interrupt receiver, sender and vector
   management(uintr_fd) (patch 6-12)
- Basic selftests (patch 13)

Along with the patches in this RFC, there are additional tests and samples that
are available at:
https://github.com/intel/uintr-linux-kernel/tree/rfc-v1

Links
=====
[1]:https://software.intel.com/content/www/us/en/develop/download/intel-architecture-instruction-set-extensions-programming-reference.html
[2]:https://libevent.org/
[3]:https://github.com/axboe/liburing
[4]:https://github.com/intel/uintr-compiler-guide/blob/uintr-gcc-11.1/UINTR-compiler-guide.pdf

Sohil Mehta (13):
   x86/uintr/man-page: Include man pages draft for reference
   Documentation/x86: Add documentation for User Interrupts
   x86/cpu: Enumerate User Interrupts support
   x86/fpu/xstate: Enumerate User Interrupts supervisor state
   x86/irq: Reserve a user IPI notification vector
   x86/uintr: Introduce uintr receiver syscalls
   x86/process/64: Add uintr task context switch support
   x86/process/64: Clean up uintr task fork and exit paths
   x86/uintr: Introduce vector registration and uintr_fd syscall
   x86/uintr: Introduce user IPI sender syscalls
   x86/uintr: Introduce uintr_wait() syscall
   x86/uintr: Wire up the user interrupt syscalls
   selftests/x86: Add basic tests for User IPI

  .../admin-guide/kernel-parameters.txt         |   2 +
  Documentation/x86/index.rst                   |   1 +
  Documentation/x86/user-interrupts.rst         | 107 +++
  arch/x86/Kconfig                              |  12 +
  arch/x86/entry/syscalls/syscall_32.tbl        |   6 +
  arch/x86/entry/syscalls/syscall_64.tbl        |   6 +
  arch/x86/include/asm/cpufeatures.h            |   1 +
  arch/x86/include/asm/disabled-features.h      |   8 +-
  arch/x86/include/asm/entry-common.h           |   4 +
  arch/x86/include/asm/fpu/types.h              |  20 +-
  arch/x86/include/asm/fpu/xstate.h             |   3 +-
  arch/x86/include/asm/hardirq.h                |   4 +
  arch/x86/include/asm/idtentry.h               |   5 +
  arch/x86/include/asm/irq_vectors.h            |   6 +-
  arch/x86/include/asm/msr-index.h              |   8 +
  arch/x86/include/asm/processor.h              |   8 +
  arch/x86/include/asm/uintr.h                  |  76 ++
  arch/x86/include/uapi/asm/processor-flags.h   |   2 +
  arch/x86/kernel/Makefile                      |   1 +
  arch/x86/kernel/cpu/common.c                  |  61 ++
  arch/x86/kernel/cpu/cpuid-deps.c              |   1 +
  arch/x86/kernel/fpu/core.c                    |  17 +
  arch/x86/kernel/fpu/xstate.c                  |  20 +-
  arch/x86/kernel/idt.c                         |   4 +
  arch/x86/kernel/irq.c                         |  51 +
  arch/x86/kernel/process.c                     |  10 +
  arch/x86/kernel/process_64.c                  |   4 +
  arch/x86/kernel/uintr_core.c                  | 880 ++++++++++++++++++
  arch/x86/kernel/uintr_fd.c                    | 300 ++++++
  include/linux/syscalls.h                      |   8 +
  include/uapi/asm-generic/unistd.h             |  15 +-
  kernel/sys_ni.c                               |   8 +
  scripts/checksyscalls.sh                      |   6 +
  tools/testing/selftests/x86/Makefile          |  10 +
  tools/testing/selftests/x86/uintr.c           | 147 +++
  tools/uintr/manpages/0_overview.txt           | 265 ++++++
  tools/uintr/manpages/1_register_receiver.txt  | 122 +++
  .../uintr/manpages/2_unregister_receiver.txt  |  62 ++
  tools/uintr/manpages/3_create_fd.txt          | 104 +++
  tools/uintr/manpages/4_register_sender.txt    | 121 +++
  tools/uintr/manpages/5_unregister_sender.txt  |  79 ++
  tools/uintr/manpages/6_wait.txt               |  59 ++
  42 files changed, 2626 insertions(+), 8 deletions(-)
  create mode 100644 Documentation/x86/user-interrupts.rst
  create mode 100644 arch/x86/include/asm/uintr.h
  create mode 100644 arch/x86/kernel/uintr_core.c
  create mode 100644 arch/x86/kernel/uintr_fd.c
  create mode 100644 tools/testing/selftests/x86/uintr.c
  create mode 100644 tools/uintr/manpages/0_overview.txt
  create mode 100644 tools/uintr/manpages/1_register_receiver.txt
  create mode 100644 tools/uintr/manpages/2_unregister_receiver.txt
  create mode 100644 tools/uintr/manpages/3_create_fd.txt
  create mode 100644 tools/uintr/manpages/4_register_sender.txt
  create mode 100644 tools/uintr/manpages/5_unregister_sender.txt
  create mode 100644 tools/uintr/manpages/6_wait.txt


base-commit: 6880fa6c56601bb8ed59df6c30fd390cc5f6dd8f

Hi All,
My apologies if this email was sent twice.
I was not sure if my previous email followed the proper reply instruction.
I resent this email using the first reply method (Saving the mbox file, importing it into my mail client, and using reply-to-all from there).
The following is our understanding of the proposed User Interrupt.

----------------------------------------------------------------------------------------

We have been exploring how user-level interrupts (UIs) can be used to
improve performance and programmability in several different areas:
e.g., parallel programming, memory management, I/O, and floating-point
libraries.  Before we venture into the discussion here, we want to
make sure we understand the proposed model. We describe our
understanding below in four sections:

1. Current target use cases
2. Preparing for future use cases
3. Basic Understanding
4. Multi-threaded parallel programming example

If people on this thread could either confirm or point out our
misunderstandings, we would appreciate it.

# Current Use Cases

The Current RFC is focused on sending an interrupt from one user-space
thread (UST) to another user-space thread (UST2UST).  These threads
could be in different processes, as long as the sender has access to
the receiver's User Interrupt File Descriptor (uifd).  Based on our
understanding, UIs are currently targeted as a low overhead
alternative for the current IPC mechanisms.

# Preparing for future use cases

Based on the RFC, we are aware that allowing a device and the kernel
to send a UI is still in development.  Both these cases would support
imprecise interrupts.  We can see a clear use case for the Device to
user-space thread (D2UST) UI, for example, supporting a fast way for a
GPU to inform a thread that it has finished executing a particular
kernel. If someone could point out an example for Kernel to
user-space thread (K2UST) UI, we would appreciate it.

In our work, we have also been exploring precise UIs from the
currently running thread.  We call these CPU to UST (CPU2UST) UIs.
For example, a SIGSEGV generated by writing to a read-only page, a
SIGFPE generated by dividing a number by zero.

- QUESTION: Is there is a rough draft/plan that we can refer to that describes the
current thinking on these three cases.

- QUESTION: Are there use cases for K2UST, or is K2UST the same as CPU2UST?

# Basic Understanding

First, we would like to make sure that our understanding of the terminology and the data structures is correct.

- User Interrupt Vector (UIV): The identity of the user interrupt.
- User Interrupt Target Table (UITT):
  This allows the sender to locate the "address" of the receiver through the uifd. - ui_frame: Argument passed to the UI handler. It contains a stack pointer, saved flags, and an instruction pointer.
- Sender: The thread that issues the `_senduipi`.
- Receiver: The thread that receives the UI from the sender.

Below outlines our understanding of the current API for UIs.

- Each thread that can receive UIs has exactly one handler
  registered with `uintr_register_handler` (a syscall).
- Each thread that registers a handler calls `uintr_create_fd` for
  every user-level interrupt vector (UIV) that they expect to receive.
- The only information delivered to the handler is the UIV.
- There are 64 UIVs that can be used per thread.
- A thread that wants to send a UI must register the receiver's uifd with `uintr_register_sender`  (a syscall).
  This returns an index the sender uses to locate the receiver.
- `_senduipi(index)` sends a user interrupt to a particular destination.
  The sender's UITT and index determine the destination.
- A thread uses `_stui` (and `_clui`) to enable (and disable) the reception of UIs.
- As for now, there is no mechanism to mask a particular UIV.
- A UI is delivered to the receiver immediately only if it is currently running. - If a thread executes the `uintr_wait()`, it will be scheduled only after receiving a UI.   There is no guarantee on the delay between the processor receiving the UI and when the thread is scheduled. - If a thread is the target of a UI and another thread is running, or the target thread is blocked in the kernel,
  then the target thread will handle the UI when it is next scheduled.
- Ordinary interrupts (interrupt delivered with CPL=0) have a higher priority over user interrupts. - UI handler only saves general-purpose registers (e.g., do not save floating-point registers). - User Interrupts with higher UIV are given a higher priority than those with smaller UIV.

## Private UITT

The Current RFC focuses on a private UITT where each thread has its own
UITT.  Thus, different threads executing `_senduipi(index1)` with the
same `index1` may cause different receiver threads to be interrupted.

In many cases, the receiver of an interrupt needs to know which thread
sent the interrupt. If we understand the proposal correctly, there are
only 64 user-level interrupt vectors (UIVs), and the UIV is the only
information transmitted to the receiver. The UIV itself allows the
receiver to distinguish different senders through careful management
of the receiver's UIV.

- QUESTION: Given the code below where the same UIV is registered twice:
```c
  uintr_fd1 = uintr_create_fd(vector1, flags)
  uintr_fd2 = uintr_create_fd(vector1, flags)
```
Would `uintr_fd1` be the same as `uintr_fd2`, or would it be registered with a different index in the UITT table?

- QUESTION: If it is registered in a different index, would the
  receiver be able to distinguish the sender if `uintr_fd1` and
  `uintr_fd2` are used from two different threads?

- QUESTION: What is the intended future use of the `flags` argument?

## Shared UITT

In the case of the shared UITT model, all the threads share the same
UITT and thus, if two different threads execute `_senduipi(index)`
with the same index, they would both cause an interrupt in the
same destination/receiver.

- QUESTION: Since both threads use the same entry (same
  destination/receiver), does this mean that the receiver will not be
  able to distinguish the sender of the interrupt?

# Multi-threaded parallel programming example

One of the uses for UIs that we have been exploring is combining the
message-passing and shared memory models for parallel programming.  In
our approach, message-passing is used for synchronization and shared
memory for data sharing.  The message passing part of the programming
pattern is based loosely on Active Messages (See ISCA92), where a
particular thread can turn off/on interrupts to ignore incoming
messages so they can execute critical sections without having to
notify any other threads in the system.

- QUESTION: Is there any data on the performance impact of `_stui` and `_clui`?

----------------------------------------------------------------------------------------


Thank you.
Best regards,
Chrisma




[Index of Archives]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [Share Photos]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux