Re: [PATCH v2 6/7] misc: bcm-vk: add Broadcom VK driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Olof/All,

I'm trying to digest all the feedback of what needs to be done.
I will be fixing up all the valuable comments about general issues but would like to know
what needs to be done about the tty interface.

The VK devices are configured to write serial data to circular buffers in memory or out a UART. When we configure a system using the UART we connect a cable to the host and open a tty device. When we don't connect a UART cable to the host we open the tty device in our driver instead.
In this case the memory is exposed to the host via PCI BAR memory space.
The bcm-vk host driver then accesses PCI space and presents a tty interface to the host.
We implemented a tty device to present the tty interface.
Host doesn't change anything other than opening a different devnode in UART vs. PCI case.

Based on all the comments: what interface should we be providing in driver instead?

On 2020-02-23 3:55 p.m., Olof Johansson wrote:
On Sat, Feb 22, 2020 at 12:03 AM Arnd Bergmann <arnd@xxxxxxxx> wrote:
On Fri, Feb 21, 2020 at 7:19 PM Scott Branden
<scott.branden@xxxxxxxxxxxx> wrote:
On 2020-02-19 11:47 p.m., Greg Kroah-Hartman wrote:
Have you worked with the V4L developers to tie this into the proper
in-kernel apis for this type of functionality?
We looked at the V4L model doesn't have any support for anything we are
doing in this driver.
We also want a driver that doesn't care about video.  It could be
offloading crypto or other operations.
We talked with Olof about all of this previously and he said leave it as
a misc driver for now.
He was going to discuss at linux plumbers conference that we need some
sort of offload engine model that such devices could fit into.
I see. Have you looked at the "uacce" driver submission? It seems
theirs is similar enough that there might be some way to share interfaces.
Uacce isn't a driver (or wasn't last time I looked at it, when it had
a different name). It's more of a framework for standardized direct HW
access from userspace, and relies on I/O virtualization to keep DMA
secure/partitioned, etc. VK is more of a classic PCIe device, it'll
handle DMA to/from the host, etc.

Using a tty driver seems like the totally incorrect way to do this, what
am I missing?
tty driver is used to provide console access to the processors running
on vk.
Data is sent using the bcm_vk_msg interface by read/write operations
from user space.
VK then gets the messages and DMA's the data to/from host memory when
needed to process.
In turn here, it sounds like you'd want to look at what drivers/misc/mic/
and the mellanox bluefield drivers are doing. As I understand, they have the
same requirements for console, but have a nicer approach of providing
abstract 'virtio' channels between the PCIe endpoint and the host, and
then run regular virtio based drivers (console, tty, block, filesystem,
network, ...) along with application specific ones to provide the custom
high-level protocols.
This has more value on the device than on the host, as far as I've
seen it used (if you want to boot Linux on it and have things
exposed).

virtio isn't necessarily a match if all you really want is a character
stream for a console and don't need (or have performance requirements
beyond what virtio offers) other types of communication.

This is also similar to what the drivers/pci/endpoint
(from the other end) as the drivers/ntb (pci host on both ends) frameworks
and of course the rpmsg/remoteproc framework do.
remoteproc is more about booting a tightly integrated device on an
embedded system. Also not a match here IMHO.

In the long run, I would want much more consolidation between the
low-level parts of all these frameworks, but moving your high-level
protocols to the same virtio method would sound like a step in the
direction towards a generialized framework and easier sharing of
the abstractions.
For a simple naive console/character stream, doing something on top of
hvc might be easier -- it already does polling for you, etc.

Of course, the intent is not to ever use it as a console for the host
here, so that aspect of hvc isn't useful. But it gives you a bunch of
other stuff for free with just getchar/putchar interfaces to
implement.


-Olof




[Index of Archives]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [Share Photos]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux