This changes the selftest output so that each test's output is prefixed
with "# " as a TAP "diagnostic line".
This creates a bit of a kernel-specific TAP dialect where the diagnostics
precede the results. The TAP spec isn't entirely clear about this, though,
so I think it's the correct solution so as to keep interactive runs making
sense. If the output _followed_ the result line in the spec-suggested
YAML form, each test would dump all of its output at once instead of as
it went, making debugging harder.
This does, however, solve the recursive TAP output problem, as sub-tests
will simply be prefixed by "# ". Parsing sub-tests becomes a simple
problem of just removing the first two characters of a given top-level
test's diagnostic output, and parsing the results.
Note that the shell construct needed to both get an exit code from
the first command in a pipe and still filter the pipe (to add the "# "
prefix) uses a POSIX solution rather than the bash "pipefail" option
which is not supported by dash.
Since some test environments may have a very minimal set of utilities
available, the new prefixing code will fall back to doing line-at-a-time
prefixing if perl and/or stdbuf are not available.
Signed-off-by: Kees Cook <keescook@xxxxxxxxxxxx>
---
tools/testing/selftests/Makefile | 1 +
tools/testing/selftests/kselftest/prefix.pl | 23 +++++++++++++
tools/testing/selftests/kselftest/runner.sh | 37 ++++++++++++++++++---
tools/testing/selftests/lib.mk | 1 +
4 files changed, 58 insertions(+), 4 deletions(-)
create mode 100755 tools/testing/selftests/kselftest/prefix.pl
diff --git a/tools/testing/selftests/Makefile b/tools/testing/selftests/Makefile
index 72178d28f9c6..2e92a9727a4d 100644
--- a/tools/testing/selftests/Makefile
+++ b/tools/testing/selftests/Makefile
@@ -133,6 +133,7 @@ ifdef INSTALL_PATH
@# Ask all targets to install their files
mkdir -p $(INSTALL_PATH)/kselftest
install -m 744 kselftest/runner.sh $(INSTALL_PATH)/kselftest/
+ install -m 744 kselftest/prefix.pl $(INSTALL_PATH)/kselftest/
@for TARGET in $(TARGETS); do \
BUILD_TARGET=$$BUILD/$$TARGET; \
make OUTPUT=$$BUILD_TARGET -C $$TARGET INSTALL_PATH=$(INSTALL_PATH)/$$TARGET install; \
diff --git a/tools/testing/selftests/kselftest/prefix.pl b/tools/testing/selftests/kselftest/prefix.pl
new file mode 100755
index 000000000000..ec7e48118183
--- /dev/null
+++ b/tools/testing/selftests/kselftest/prefix.pl
@@ -0,0 +1,23 @@
+#!/usr/bin/perl
+# SPDX-License-Identifier: GPL-2.0
+# Prefix all lines with "# ", unbuffered. Command being piped in may need
+# to have unbuffering forced with "stdbuf -i0 -o0 -e0 $cmd".
+use strict;
+
+binmode STDIN;
+binmode STDOUT;
+
+STDOUT->autoflush(1);
+
+my $needed = 1;
+while (1) {
+ my $char;
+ my $bytes = sysread(STDIN, $char, 1);
+ exit 0 if ($bytes == 0);
+ if ($needed) {
+ print "# ";
+ $needed = 0;
+ }
+ print $char;
+ $needed = 1 if ($char eq "\n");
+}
diff --git a/tools/testing/selftests/kselftest/runner.sh b/tools/testing/selftests/kselftest/runner.sh
index 5793660dbe3f..f8b545a6e0e9 100644
--- a/tools/testing/selftests/kselftest/runner.sh
+++ b/tools/testing/selftests/kselftest/runner.sh
@@ -5,6 +5,34 @@ export KSFT_TAP_LEVEL=1
export skip_rc=4
export logfile=/dev/stdout
+# There isn't a shell-agnostic way to find the path of a sourced file,
+# so we must rely on BASE_DIR being set to find other tools.
+if [ -z "$BASE_DIR" ]; then
+ echo "Error: BASE_DIR must be set before sourcing." >&2
+ exit 1
+fi
+
+# If Perl is unavailable, we must fall back to line-at-a-time prefixing
+# with sed instead of unbuffered output.
+tap_prefix()
+{
+ if [ ! -x /usr/bin/perl ]; then
+ sed -e 's/^/# /'
+ else
+ "$BASE_DIR"/kselftest/prefix.pl
+ fi
+}
+
+# If stdbuf is unavailable, we must fall back to line-at-a-time piping.
+tap_unbuffer()
+{
+ if ! which stdbuf >/dev/null ; then
+ "$@"
+ else
+ stdbuf -i0 -o0 -e0 "$@"
+ fi
+}
+
run_one()
{
DIR="$1"
@@ -14,10 +42,9 @@ run_one()
BASENAME_TEST=$(basename $TEST)
TEST_HDR_MSG="selftests: $DIR: $BASENAME_TEST"
- echo "$TEST_HDR_MSG"
- echo "========================================"
+ echo "# $TEST_HDR_MSG"
if [ ! -x "$TEST" ]; then
- echo -n "$TEST_HDR_MSG: Warning: file $TEST is "
+ echo -n "# Warning: file $TEST is "
if [ ! -e "$TEST" ]; then
echo "missing!"
else
@@ -26,7 +53,9 @@ run_one()
echo "not ok $test_num $TEST_HDR_MSG"
else
cd `dirname $TEST` > /dev/null
- (./$BASENAME_TEST >> "$logfile" 2>&1 &&
+ (((((tap_unbuffer ./$BASENAME_TEST 2>&1; echo $? >&3) |
+ tap_prefix >&4) 3>&1) |
+ (read xs; exit $xs)) 4>>"$logfile" &&
echo "ok $test_num $TEST_HDR_MSG") ||
(if [ $? -eq $skip_rc ]; then \
echo "not ok $test_num $TEST_HDR_MSG # SKIP"
diff --git a/tools/testing/selftests/lib.mk b/tools/testing/selftests/lib.mk
index 8be13d117101..5c6505bec8be 100644
--- a/tools/testing/selftests/lib.mk
+++ b/tools/testing/selftests/lib.mk
@@ -33,6 +33,7 @@ endif
.ONESHELL:
define RUN_TESTS
+ BASE_DIR="$(selfdir)"; \
. $(selfdir)/kselftest/runner.sh; \
run_many $(1)
endef
--
2.17.1
