On Mon, Jan 16, 2023 at 01:09:19PM +0300, Dan Carpenter wrote:
> Hello Piergiorgio Beruto,
>
> The patch 493323416fed: "drivers/net/phy: add helpers to get/set PLCA
> configuration" from Jan 9, 2023, leads to the following Smatch static
> checker warning:
>
> drivers/net/phy/phy-c45.c:1036 genphy_c45_plca_set_cfg()
> error: uninitialized symbol 'val'.
>
> drivers/net/phy/phy-c45.c
> 999 int genphy_c45_plca_set_cfg(struct phy_device *phydev,
> 1000 const struct phy_plca_cfg *plca_cfg)
> 1001 {
> 1002 int ret;
> 1003 u16 val;
> 1004
> 1005 // PLCA IDVER is read-only
> 1006 if (plca_cfg->version >= 0)
> 1007 return -EINVAL;
> 1008
> 1009 // first of all, disable PLCA if required
> 1010 if (plca_cfg->enabled == 0) {
> 1011 ret = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2,
> 1012 MDIO_OATC14_PLCA_CTRL0,
> 1013 MDIO_OATC14_PLCA_EN);
> 1014
> 1015 if (ret < 0)
> 1016 return ret;
> 1017 }
> 1018
> 1019 // check if we need to set the PLCA node count, node ID, or both
> 1020 if (plca_cfg->node_cnt >= 0 || plca_cfg->node_id >= 0) {
>
> Let's assume both conditions are true
>
> 1021 /* if one between node count and node ID is -not- to be
> 1022 * changed, read the register to later perform merge/purge of
> 1023 * the configuration as appropriate
> 1024 */
> 1025 if (plca_cfg->node_cnt < 0 || plca_cfg->node_id < 0) {
>
> Then neither condition is true here
>
> 1026 ret = phy_read_mmd(phydev, MDIO_MMD_VEND2,
> 1027 MDIO_OATC14_PLCA_CTRL1);
> 1028
> 1029 if (ret < 0)
> 1030 return ret;
> 1031
> 1032 val = ret;
> 1033 }
> 1034
> 1035 if (plca_cfg->node_cnt >= 0)
> 1036 val = (val & ~MDIO_OATC14_PLCA_NCNT) |
> ^^^
> Uninitialized
This is correct, however it is not a real problem. Please, allow me to
explain. If both conditions are true (initially) then both conditions at
lines 1035 and 1039 will be true as well. This means that the content of
'val' is completely overwritten with the content of node_cnt and
node_id. This is because the register is 16 bits and node_cnt/id are 8
bits each. Therefore, regardless of the initial status of 'val', its
content is fully determines after line 1039.
With that said, I have no issues in initializing val to 0 if you think
it's still worth it after my explanation.
>
> 1037 (plca_cfg->node_cnt << 8);
> 1038
> 1039 if (plca_cfg->node_id >= 0)
> 1040 val = (val & ~MDIO_OATC14_PLCA_ID) |
> 1041 (plca_cfg->node_id);
>
>
> regards,
> dan carpenter
Thank you very much for reporting this,
Kind Regards,
Piergiorgio
