Re: [PATCH] devfreq/exynos-bus: Use common error handling code in exynos_bus_target()

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Markus,

As I already commented on your other patch related to extcon-max14577,
this patch might remove the redundant error message. But, it makes
the code more complicated in side of readability. I prefer existing code.

On 2017년 10월 22일 22:40, SF Markus Elfring wrote:
> From: Markus Elfring <elfring@xxxxxxxxxxxxxxxxxxxxx>
> Date: Sun, 22 Oct 2017 15:33:06 +0200
> 
> Adjust jump targets so that a bit of exception handling can be better
> reused at the end of this function.
> 
> This issue was detected by using the Coccinelle software.
> 
> Signed-off-by: Markus Elfring <elfring@xxxxxxxxxxxxxxxxxxxxx>
> ---
>  drivers/devfreq/exynos-bus.c | 21 ++++++++++-----------
>  1 file changed, 10 insertions(+), 11 deletions(-)
> 
> diff --git a/drivers/devfreq/exynos-bus.c b/drivers/devfreq/exynos-bus.c
> index 49f68929e024..e38d456b2d7d 100644
> --- a/drivers/devfreq/exynos-bus.c
> +++ b/drivers/devfreq/exynos-bus.c
> @@ -124,34 +124,33 @@ static int exynos_bus_target(struct device *dev, unsigned long *freq, u32 flags)
>  
>  	if (old_freq < new_freq) {
>  		ret = regulator_set_voltage_tol(bus->regulator, new_volt, tol);
> -		if (ret < 0) {
> -			dev_err(bus->dev, "failed to set voltage\n");
> -			goto out;
> -		}
> +		if (ret < 0)
> +			goto report_failure;
>  	}
>  
>  	ret = clk_set_rate(bus->clk, new_freq);
>  	if (ret < 0) {
>  		dev_err(dev, "failed to change clock of bus\n");
>  		clk_set_rate(bus->clk, old_freq);
> -		goto out;
> +		goto unlock;
>  	}
>  
>  	if (old_freq > new_freq) {
>  		ret = regulator_set_voltage_tol(bus->regulator, new_volt, tol);
> -		if (ret < 0) {
> -			dev_err(bus->dev, "failed to set voltage\n");
> -			goto out;
> -		}
> +		if (ret < 0)
> +			goto report_failure;
>  	}
>  	bus->curr_freq = new_freq;
>  
>  	dev_dbg(dev, "Set the frequency of bus (%luHz -> %luHz, %luHz)\n",
>  			old_freq, new_freq, clk_get_rate(bus->clk));
> -out:
> +unlock:
>  	mutex_unlock(&bus->lock);
> -
>  	return ret;
> +
> +report_failure:
> +	dev_err(bus->dev, "failed to set voltage\n");
> +	goto unlock;
>  }
>  
>  static int exynos_bus_get_dev_status(struct device *dev,
> 


-- 
Best Regards,
Chanwoo Choi
Samsung Electronics
--
To unsubscribe from this list: send the line "unsubscribe kernel-janitors" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Kernel Development]     [Kernel Announce]     [Kernel Newbies]     [Linux Networking Development]     [Share Photos]     [IDE]     [Security]     [Git]     [Netfilter]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Device Mapper]

  Powered by Linux