Use tabs instead of spaces in a set of statements and fix lines over 80 chars. Reported by checkpatch. Tested by compilation only. Signed-off-by: Peter Senna Tschudin <peter.senna@xxxxxxxxx> --- Cahnges from V4: - Fix identation issue found on V4 drivers/staging/vt6656/main_usb.c | 44 ++++++++++++++++++++------------------- 1 file changed, 23 insertions(+), 21 deletions(-) diff --git a/drivers/staging/vt6656/main_usb.c b/drivers/staging/vt6656/main_usb.c index 553a8e9..cc0281a 100644 --- a/drivers/staging/vt6656/main_usb.c +++ b/drivers/staging/vt6656/main_usb.c @@ -382,38 +382,40 @@ static int device_init_registers(struct vnt_private *pDevice) /* load vt3266 calibration parameters in EEPROM */ if (pDevice->byRFType == RF_VT3226D0) { if ((pDevice->abyEEPROM[EEP_OFS_MAJOR_VER] == 0x1) && - (pDevice->abyEEPROM[EEP_OFS_MINOR_VER] >= 0x4)) { + (pDevice->abyEEPROM[EEP_OFS_MINOR_VER] >= 0x4)) { byCalibTXIQ = pDevice->abyEEPROM[EEP_OFS_CALIB_TX_IQ]; byCalibTXDC = pDevice->abyEEPROM[EEP_OFS_CALIB_TX_DC]; byCalibRXIQ = pDevice->abyEEPROM[EEP_OFS_CALIB_RX_IQ]; if (byCalibTXIQ || byCalibTXDC || byCalibRXIQ) { - /* CR255, enable TX/RX IQ and DC compensation mode */ + /* CR255, enable TX/RX IQ and + DC compensation mode */ vnt_control_out_u8(pDevice, - MESSAGE_REQUEST_BBREG, - 0xff, - 0x03); - /* CR251, TX I/Q Imbalance Calibration */ + MESSAGE_REQUEST_BBREG, + 0xff, + 0x03); + /* CR251, TX I/Q Imbalance Calibration */ vnt_control_out_u8(pDevice, - MESSAGE_REQUEST_BBREG, - 0xfb, - byCalibTXIQ); - /* CR252, TX DC-Offset Calibration */ + MESSAGE_REQUEST_BBREG, + 0xfb, + byCalibTXIQ); + /* CR252, TX DC-Offset Calibration */ vnt_control_out_u8(pDevice, - MESSAGE_REQUEST_BBREG, - 0xfC, - byCalibTXDC); - /* CR253, RX I/Q Imbalance Calibration */ + MESSAGE_REQUEST_BBREG, + 0xfC, + byCalibTXDC); + /* CR253, RX I/Q Imbalance Calibration */ vnt_control_out_u8(pDevice, - MESSAGE_REQUEST_BBREG, - 0xfd, - byCalibRXIQ); + MESSAGE_REQUEST_BBREG, + 0xfd, + byCalibRXIQ); } else { - /* CR255, turn off BB Calibration compensation */ + /* CR255, turn off + BB Calibration compensation */ vnt_control_out_u8(pDevice, - MESSAGE_REQUEST_BBREG, - 0xff, - 0x0); + MESSAGE_REQUEST_BBREG, + 0xff, + 0x0); } } } -- 1.9.3 -- To unsubscribe from this list: send the line "unsubscribe kernel-janitors" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html