On Fri, Sep 6, 2024 at 8:01 PM Daniel Gomez via B4 Relay <devnull+da.gomez.samsung.com@xxxxxxxxxx> wrote: > > From: Daniel Gomez <da.gomez@xxxxxxxxxxx> > > Add documentation under kbuild/llvm to inform about the experimental > support for building the Linux kernel in macOS hosts environments. > > Signed-off-by: Daniel Gomez <da.gomez@xxxxxxxxxxx> Instead, you can add this instruction to: https://github.com/bee-headers/homebrew-bee-headers/blob/main/README.md > --- > Documentation/kbuild/llvm.rst | 78 +++++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 78 insertions(+) > > diff --git a/Documentation/kbuild/llvm.rst b/Documentation/kbuild/llvm.rst > index 6dc66b4f31a7..de3bde925793 100644 > --- a/Documentation/kbuild/llvm.rst > +++ b/Documentation/kbuild/llvm.rst > @@ -186,6 +186,84 @@ yet. Bug reports are always welcome at the issue tracker below! > - Supported > - ``LLVM=1`` > > +Experimental Build in macOS > +--------------------------- > + > +Building on macOS with LLVM is experimental. This section provides steps to > +install dependencies via Homebrew, set up the environment, and start the build > +process. > + > +1. **Create a Case-Sensitive Volume** > + > + For fetching and building the project, you need a case-sensitive volume. Use the following > + command to create one: > + > + .. code-block:: shell > + > + diskutil apfs addVolume /dev/disk<N> "Case-sensitive APFS" linux > + > + Replace `/dev/disk<N>` with the appropriate disk identifier. > + > +2. **Install Build Dependencies** > + > +Use Homebrew to install the required build dependencies. > + > +- **Core Utilities**: `coreutils`, `findutils`, `gnu-sed`, `gnu-tar`, `grep`, > + `llvm`, `make`, and `pkg-config`. > + > + .. code-block:: shell > + > + brew install coreutils findutils gnu-sed gnu-tar grep llvm make pkg-config > + > +- **Bee Headers**: Install byteswap, elf and endian headers using the > + `Bee Headers Project <https://github.com/bee-headers/headers>`_. > + > + .. code-block:: shell > + > + brew tap bee-headers/bee-headers > + brew install bee-headers/bee-headers/bee-headers > + > + After installation, verify the `CFLAGS` with `pkg-config`: > + > + .. code-block:: shell > + > + pkg-config --cflags bee-headers > + -I/opt/homebrew/Cellar/bee-headers/0.1/include > + > +3. **Configure the PATH** > + > + Include all the required GNU tools and LLVM in your `PATH`. This ensures that > + the necessary tools are available during the build process. > + > + .. code-block:: shell > + > + PATH="/opt/homebrew/opt/coreutils/libexec/gnubin:$PATH" > + PATH="/opt/homebrew/opt/findutils/libexec/gnubin:$PATH" > + PATH="/opt/homebrew/opt/gnu-sed/libexec/gnubin:$PATH" > + PATH="/opt/homebrew/opt/gnu-tar/libexec/gnubin:$PATH" > + PATH="/opt/homebrew/opt/grep/libexec/gnubin:$PATH" > + PATH="/opt/homebrew/opt/make/libexec/gnubin:$PATH" > + PATH="/opt/homebrew/opt/llvm/bin:$PATH" > + > +Building the Project > +-------------------- > + > +Once the environment is set up, you can start the build process using LLVM. Run > +the following commands to initiate the build: > + > +.. code-block:: shell > + > + make LLVM=1 allyesconfig > + make LLVM=1 -j$(nproc) > + > +Supported in macOS > +~~~~~~~~~~~~~~~~~~ > + > +At the moment, only arm64 is supported and tested with `allyesconfig` Makefile > +configuration target. Other Kconfig options not included in `allyesconfig` > +target and architectures may be supported as well as support in macOS is based > +on LLVM effort and maintenance. > + > Getting Help > ------------ > > > -- > 2.46.0 > > -- Best Regards Masahiro Yamada