-Wa,-msoft-float is tested with as-option, which will be a problem for clang with an upcoming change to move as-option to use KBUILD_AFLAGS instead of KBUILD_CFLAGS due to a lack of '-mno-abicalls' in KBUILD_AFLAGS at the point that this check occurs; $(cflags-y) is added to KBUILD_AFLAGS towards the end of this file. clang: error: ignoring '-fno-PIE' option as it cannot be used with implicit usage of -mabicalls and the N64 ABI [-Werror,-Woption-ignored] This could be resolved by switching to a cc-option check but '$(cflags-y)' would need to be added so that '-mno-abicalls' is present for the test. However, this check is no longer necessary, as -msoft-float is supported by all supported assembler versions (GNU as 2.25+ and LLVM 11+). Eliminate GAS_HAS_SET_HARDFLOAT and all of its uses, inlining SET_HARDFLOAT where necessary. Link: https://lore.kernel.org/202209101939.bvk64Fok-lkp@xxxxxxxxx/ Reported-by: kernel test robot <lkp@xxxxxxxxx> Signed-off-by: Nathan Chancellor <nathan@xxxxxxxxxx> Acked-by: Thomas Bogendoerfer <tsbogend@xxxxxxxxxxxxxxxx> Reviewed-by: Nick Desaulniers <ndesaulniers@xxxxxxxxxx> Reviewed-by: Philippe Mathieu-Daudé <philmd@xxxxxxxxxx> --- Cc: linux-mips@xxxxxxxxxxxxxxx --- arch/mips/Makefile | 11 +--------- arch/mips/include/asm/asmmacro-32.h | 4 ++-- arch/mips/include/asm/asmmacro.h | 42 ++++++++++++++++++------------------- arch/mips/include/asm/fpregdef.h | 14 ------------- arch/mips/include/asm/mipsregs.h | 20 ++++-------------- arch/mips/kernel/genex.S | 2 +- arch/mips/kernel/r2300_fpu.S | 4 ++-- arch/mips/kernel/r4k_fpu.S | 12 +++++------ arch/mips/kvm/fpu.S | 6 +++--- 9 files changed, 40 insertions(+), 75 deletions(-) diff --git a/arch/mips/Makefile b/arch/mips/Makefile index 490dea07d4e0..a00a6d94e16f 100644 --- a/arch/mips/Makefile +++ b/arch/mips/Makefile @@ -95,7 +95,7 @@ all-$(CONFIG_SYS_SUPPORTS_ZBOOT)+= vmlinuz # crossformat linking we rely on the elf2ecoff tool for format conversion. # cflags-y += -G 0 -mno-abicalls -fno-pic -pipe -cflags-y += -msoft-float +cflags-y += -msoft-float -Wa,-msoft-float LDFLAGS_vmlinux += -G 0 -static -n -nostdlib KBUILD_AFLAGS_MODULE += -mlong-calls KBUILD_CFLAGS_MODULE += -mlong-calls @@ -104,15 +104,6 @@ ifeq ($(CONFIG_RELOCATABLE),y) LDFLAGS_vmlinux += --emit-relocs endif -# -# pass -msoft-float to GAS if it supports it. However on newer binutils -# (specifically newer than 2.24.51.20140728) we then also need to explicitly -# set ".set hardfloat" in all files which manipulate floating point registers. -# -ifneq ($(call as-option,-Wa$(comma)-msoft-float,),) - cflags-y += -DGAS_HAS_SET_HARDFLOAT -Wa,-msoft-float -endif - cflags-y += -ffreestanding cflags-$(CONFIG_CPU_BIG_ENDIAN) += -EB diff --git a/arch/mips/include/asm/asmmacro-32.h b/arch/mips/include/asm/asmmacro-32.h index 1c08c1f7903c..83a4940b7c89 100644 --- a/arch/mips/include/asm/asmmacro-32.h +++ b/arch/mips/include/asm/asmmacro-32.h @@ -15,7 +15,7 @@ .macro fpu_save_single thread tmp=t0 .set push - SET_HARDFLOAT + .set hardfloat cfc1 \tmp, fcr31 s.d $f0, THREAD_FPR0(\thread) s.d $f2, THREAD_FPR2(\thread) @@ -39,7 +39,7 @@ .macro fpu_restore_single thread tmp=t0 .set push - SET_HARDFLOAT + .set hardfloat lw \tmp, THREAD_FCR31(\thread) l.d $f0, THREAD_FPR0(\thread) l.d $f2, THREAD_FPR2(\thread) diff --git a/arch/mips/include/asm/asmmacro.h b/arch/mips/include/asm/asmmacro.h index ca83ada7015f..1c4438f3f2ab 100644 --- a/arch/mips/include/asm/asmmacro.h +++ b/arch/mips/include/asm/asmmacro.h @@ -83,7 +83,7 @@ .macro fpu_save_16even thread tmp=t0 .set push - SET_HARDFLOAT + .set hardfloat cfc1 \tmp, fcr31 sdc1 $f0, THREAD_FPR0(\thread) sdc1 $f2, THREAD_FPR2(\thread) @@ -109,7 +109,7 @@ .set push .set mips64r2 .set fp=64 - SET_HARDFLOAT + .set hardfloat sdc1 $f1, THREAD_FPR1(\thread) sdc1 $f3, THREAD_FPR3(\thread) sdc1 $f5, THREAD_FPR5(\thread) @@ -142,7 +142,7 @@ .macro fpu_restore_16even thread tmp=t0 .set push - SET_HARDFLOAT + .set hardfloat lw \tmp, THREAD_FCR31(\thread) ldc1 $f0, THREAD_FPR0(\thread) ldc1 $f2, THREAD_FPR2(\thread) @@ -168,7 +168,7 @@ .set push .set mips64r2 .set fp=64 - SET_HARDFLOAT + .set hardfloat ldc1 $f1, THREAD_FPR1(\thread) ldc1 $f3, THREAD_FPR3(\thread) ldc1 $f5, THREAD_FPR5(\thread) @@ -373,7 +373,7 @@ .macro _cfcmsa rd, cs .set push .set noat - SET_HARDFLOAT + .set hardfloat insn_if_mips 0x787e0059 | (\cs << 11) insn32_if_mm 0x587e0056 | (\cs << 11) move \rd, $1 @@ -383,7 +383,7 @@ .macro _ctcmsa cd, rs .set push .set noat - SET_HARDFLOAT + .set hardfloat move $1, \rs insn_if_mips 0x783e0819 | (\cd << 6) insn32_if_mm 0x583e0816 | (\cd << 6) @@ -393,7 +393,7 @@ .macro ld_b wd, off, base .set push .set noat - SET_HARDFLOAT + .set hardfloat PTR_ADDU $1, \base, \off insn_if_mips 0x78000820 | (\wd << 6) insn32_if_mm 0x58000807 | (\wd << 6) @@ -403,7 +403,7 @@ .macro ld_h wd, off, base .set push .set noat - SET_HARDFLOAT + .set hardfloat PTR_ADDU $1, \base, \off insn_if_mips 0x78000821 | (\wd << 6) insn32_if_mm 0x58000817 | (\wd << 6) @@ -413,7 +413,7 @@ .macro ld_w wd, off, base .set push .set noat - SET_HARDFLOAT + .set hardfloat PTR_ADDU $1, \base, \off insn_if_mips 0x78000822 | (\wd << 6) insn32_if_mm 0x58000827 | (\wd << 6) @@ -423,7 +423,7 @@ .macro ld_d wd, off, base .set push .set noat - SET_HARDFLOAT + .set hardfloat PTR_ADDU $1, \base, \off insn_if_mips 0x78000823 | (\wd << 6) insn32_if_mm 0x58000837 | (\wd << 6) @@ -433,7 +433,7 @@ .macro st_b wd, off, base .set push .set noat - SET_HARDFLOAT + .set hardfloat PTR_ADDU $1, \base, \off insn_if_mips 0x78000824 | (\wd << 6) insn32_if_mm 0x5800080f | (\wd << 6) @@ -443,7 +443,7 @@ .macro st_h wd, off, base .set push .set noat - SET_HARDFLOAT + .set hardfloat PTR_ADDU $1, \base, \off insn_if_mips 0x78000825 | (\wd << 6) insn32_if_mm 0x5800081f | (\wd << 6) @@ -453,7 +453,7 @@ .macro st_w wd, off, base .set push .set noat - SET_HARDFLOAT + .set hardfloat PTR_ADDU $1, \base, \off insn_if_mips 0x78000826 | (\wd << 6) insn32_if_mm 0x5800082f | (\wd << 6) @@ -463,7 +463,7 @@ .macro st_d wd, off, base .set push .set noat - SET_HARDFLOAT + .set hardfloat PTR_ADDU $1, \base, \off insn_if_mips 0x78000827 | (\wd << 6) insn32_if_mm 0x5800083f | (\wd << 6) @@ -473,7 +473,7 @@ .macro copy_s_w ws, n .set push .set noat - SET_HARDFLOAT + .set hardfloat insn_if_mips 0x78b00059 | (\n << 16) | (\ws << 11) insn32_if_mm 0x58b00056 | (\n << 16) | (\ws << 11) .set pop @@ -482,7 +482,7 @@ .macro copy_s_d ws, n .set push .set noat - SET_HARDFLOAT + .set hardfloat insn_if_mips 0x78b80059 | (\n << 16) | (\ws << 11) insn32_if_mm 0x58b80056 | (\n << 16) | (\ws << 11) .set pop @@ -491,7 +491,7 @@ .macro insert_w wd, n .set push .set noat - SET_HARDFLOAT + .set hardfloat insn_if_mips 0x79300819 | (\n << 16) | (\wd << 6) insn32_if_mm 0x59300816 | (\n << 16) | (\wd << 6) .set pop @@ -500,7 +500,7 @@ .macro insert_d wd, n .set push .set noat - SET_HARDFLOAT + .set hardfloat insn_if_mips 0x79380819 | (\n << 16) | (\wd << 6) insn32_if_mm 0x59380816 | (\n << 16) | (\wd << 6) .set pop @@ -553,7 +553,7 @@ st_d 29, THREAD_FPR29 - FPR_BASE_OFFS, FPR_BASE st_d 30, THREAD_FPR30 - FPR_BASE_OFFS, FPR_BASE st_d 31, THREAD_FPR31 - FPR_BASE_OFFS, FPR_BASE - SET_HARDFLOAT + .set hardfloat _cfcmsa $1, MSA_CSR sw $1, THREAD_MSA_CSR(\thread) .set pop @@ -562,7 +562,7 @@ .macro msa_restore_all thread .set push .set noat - SET_HARDFLOAT + .set hardfloat lw $1, THREAD_MSA_CSR(\thread) _ctcmsa MSA_CSR, $1 #ifdef TOOLCHAIN_SUPPORTS_MSA @@ -618,7 +618,7 @@ .macro msa_init_all_upper .set push .set noat - SET_HARDFLOAT + .set hardfloat not $1, zero msa_init_upper 0 msa_init_upper 1 diff --git a/arch/mips/include/asm/fpregdef.h b/arch/mips/include/asm/fpregdef.h index f184ba088532..429481f9028d 100644 --- a/arch/mips/include/asm/fpregdef.h +++ b/arch/mips/include/asm/fpregdef.h @@ -14,20 +14,6 @@ #include <asm/sgidefs.h> -/* - * starting with binutils 2.24.51.20140729, MIPS binutils warn about mixing - * hardfloat and softfloat object files. The kernel build uses soft-float by - * default, so we also need to pass -msoft-float along to GAS if it supports it. - * But this in turn causes assembler errors in files which access hardfloat - * registers. We detect if GAS supports "-msoft-float" in the Makefile and - * explicitly put ".set hardfloat" where floating point registers are touched. - */ -#ifdef GAS_HAS_SET_HARDFLOAT -#define SET_HARDFLOAT .set hardfloat -#else -#define SET_HARDFLOAT -#endif - #if _MIPS_SIM == _MIPS_SIM_ABI32 /* diff --git a/arch/mips/include/asm/mipsregs.h b/arch/mips/include/asm/mipsregs.h index 99eeafe6dcab..2d53704d9f24 100644 --- a/arch/mips/include/asm/mipsregs.h +++ b/arch/mips/include/asm/mipsregs.h @@ -2367,7 +2367,7 @@ do { \ /* * Macros to access the floating point coprocessor control registers */ -#define _read_32bit_cp1_register(source, gas_hardfloat) \ +#define read_32bit_cp1_register(source) \ ({ \ unsigned int __res; \ \ @@ -2377,36 +2377,24 @@ do { \ " # gas fails to assemble cfc1 for some archs, \n" \ " # like Octeon. \n" \ " .set mips1 \n" \ - " "STR(gas_hardfloat)" \n" \ + " .set hardfloat \n" \ " cfc1 %0,"STR(source)" \n" \ " .set pop \n" \ : "=r" (__res)); \ __res; \ }) -#define _write_32bit_cp1_register(dest, val, gas_hardfloat) \ +#define write_32bit_cp1_register(dest, val) \ do { \ __asm__ __volatile__( \ " .set push \n" \ " .set reorder \n" \ - " "STR(gas_hardfloat)" \n" \ + " .set hardfloat \n" \ " ctc1 %0,"STR(dest)" \n" \ " .set pop \n" \ : : "r" (val)); \ } while (0) -#ifdef GAS_HAS_SET_HARDFLOAT -#define read_32bit_cp1_register(source) \ - _read_32bit_cp1_register(source, .set hardfloat) -#define write_32bit_cp1_register(dest, val) \ - _write_32bit_cp1_register(dest, val, .set hardfloat) -#else -#define read_32bit_cp1_register(source) \ - _read_32bit_cp1_register(source, ) -#define write_32bit_cp1_register(dest, val) \ - _write_32bit_cp1_register(dest, val, ) -#endif - #ifdef TOOLCHAIN_SUPPORTS_DSP #define rddsp(mask) \ ({ \ diff --git a/arch/mips/kernel/genex.S b/arch/mips/kernel/genex.S index 3425df6019c0..b6de8e88c1bd 100644 --- a/arch/mips/kernel/genex.S +++ b/arch/mips/kernel/genex.S @@ -480,7 +480,7 @@ NESTED(nmi_handler, PT_SIZE, sp) .set push /* gas fails to assemble cfc1 for some archs (octeon).*/ \ .set mips1 - SET_HARDFLOAT + .set hardfloat cfc1 a1, fcr31 .set pop .endm diff --git a/arch/mips/kernel/r2300_fpu.S b/arch/mips/kernel/r2300_fpu.S index 2748c55820c2..6c745aa9e825 100644 --- a/arch/mips/kernel/r2300_fpu.S +++ b/arch/mips/kernel/r2300_fpu.S @@ -64,7 +64,7 @@ LEAF(_restore_fp) */ LEAF(_save_fp_context) .set push - SET_HARDFLOAT + .set hardfloat li v0, 0 # assume success cfc1 t1, fcr31 EX2(s.d $f0, 0(a0)) @@ -98,7 +98,7 @@ LEAF(_save_fp_context) */ LEAF(_restore_fp_context) .set push - SET_HARDFLOAT + .set hardfloat li v0, 0 # assume success EX(lw t0, (a1)) EX2(l.d $f0, 0(a0)) diff --git a/arch/mips/kernel/r4k_fpu.S b/arch/mips/kernel/r4k_fpu.S index 2e687c60bc4f..4e8c98517d9d 100644 --- a/arch/mips/kernel/r4k_fpu.S +++ b/arch/mips/kernel/r4k_fpu.S @@ -26,7 +26,7 @@ .macro EX insn, reg, src .set push - SET_HARDFLOAT + .set hardfloat .set nomacro .ex\@: \insn \reg, \src .set pop @@ -98,14 +98,14 @@ LEAF(_init_msa_upper) */ LEAF(_save_fp_context) .set push - SET_HARDFLOAT + .set hardfloat cfc1 t1, fcr31 .set pop #if defined(CONFIG_64BIT) || defined(CONFIG_CPU_MIPSR2) || \ defined(CONFIG_CPU_MIPSR5) || defined(CONFIG_CPU_MIPSR6) .set push - SET_HARDFLOAT + .set hardfloat #if defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR5) .set mips32r2 .set fp=64 @@ -135,7 +135,7 @@ LEAF(_save_fp_context) #endif .set push - SET_HARDFLOAT + .set hardfloat /* Store the 16 even double precision registers */ EX sdc1 $f0, 0(a0) EX sdc1 $f2, 16(a0) @@ -173,7 +173,7 @@ LEAF(_restore_fp_context) #if defined(CONFIG_64BIT) || defined(CONFIG_CPU_MIPSR2) || \ defined(CONFIG_CPU_MIPSR5) || defined(CONFIG_CPU_MIPSR6) .set push - SET_HARDFLOAT + .set hardfloat #if defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR5) .set mips32r2 .set fp=64 @@ -201,7 +201,7 @@ LEAF(_restore_fp_context) 1: .set pop #endif .set push - SET_HARDFLOAT + .set hardfloat EX ldc1 $f0, 0(a0) EX ldc1 $f2, 16(a0) EX ldc1 $f4, 32(a0) diff --git a/arch/mips/kvm/fpu.S b/arch/mips/kvm/fpu.S index 16f17c6390dd..eb2e8cc3532f 100644 --- a/arch/mips/kvm/fpu.S +++ b/arch/mips/kvm/fpu.S @@ -22,7 +22,7 @@ LEAF(__kvm_save_fpu) .set push - SET_HARDFLOAT + .set hardfloat .set fp=64 mfc0 t0, CP0_STATUS sll t0, t0, 5 # is Status.FR set? @@ -66,7 +66,7 @@ LEAF(__kvm_save_fpu) LEAF(__kvm_restore_fpu) .set push - SET_HARDFLOAT + .set hardfloat .set fp=64 mfc0 t0, CP0_STATUS sll t0, t0, 5 # is Status.FR set? @@ -110,7 +110,7 @@ LEAF(__kvm_restore_fpu) LEAF(__kvm_restore_fcsr) .set push - SET_HARDFLOAT + .set hardfloat lw t0, VCPU_FCR31(a0) /* * The ctc1 must stay at this offset in __kvm_restore_fcsr. -- 2.39.0
