On Sun, 2014-07-06 at 12:02 +0400, Konstantin Khlebnikov wrote: > This patch makes cross-compilation configuration fully statefull. > Default ARCH is stored in .config as CONFIG_DEFAULT_ARCH. > After initial configuration specifying ARCH= is no longer required. > > To avoid recursion it is read directly from .config using scritps/config > because include/config/auto.conf is not yet included at this point. > > Signed-off-by: Konstantin Khlebnikov <koct9i@xxxxxxxxx> > --- It this needed because the Kconfig symbol ARCH is set only if ARCH is set in the environment? Could the same result be had by saving CONFIG_ARCH in .config (I suppose it actually already is) and then use its value on builds with that .config unless ARCH is specified in the environment again? Ie, change the "option env=[...]" semantics a bit, perhaps by special casing CONFIG_ARCH. > Documentation/kbuild/makefiles.txt | 2 ++ > Makefile | 19 ++++++++++++++----- > init/Kconfig | 4 ++++ > 3 files changed, 20 insertions(+), 5 deletions(-) > > diff --git a/Documentation/kbuild/makefiles.txt b/Documentation/kbuild/makefiles.txt > index c600e2f..ced3e42 100644 > --- a/Documentation/kbuild/makefiles.txt > +++ b/Documentation/kbuild/makefiles.txt > @@ -1394,6 +1394,8 @@ The top Makefile exports the following variables: > > make ARCH=m68k ... > > + Default $(ARCH) is stored in .config as CONFIG_DEFAULT_ARCH, > + so overriding is required only for initial configuration. > > INSTALL_PATH > > diff --git a/Makefile b/Makefile > index 50fb690..76fcd9f 100644 > --- a/Makefile > +++ b/Makefile > @@ -171,6 +171,8 @@ VPATH := $(srctree)$(if $(KBUILD_EXTMOD),:$(KBUILD_EXTMOD)) > > export srctree objtree VPATH > > +KCONFIG_CONFIG ?= .config > +export KCONFIG_CONFIG > > # SUBARCH tells the usermode build what the underlying arch is. That is set > # first, and if a usermode build is happening, the "ARCH=um" on the command > @@ -193,7 +195,18 @@ SUBARCH := $(shell uname -m | sed -e s/i.86/x86/ -e s/x86_64/x86/ \ > # ARCH can be set during invocation of make: > # make ARCH=ia64 > # Another way is to have ARCH set in the environment. > -# The default ARCH is the host where make is executed. > +# If CONFIG_DEFAULT_ARCH is in .config its value is used as default ARCH, > +# otherwise the host where make is executed. > + > +ifndef ARCH > + ARCH := $(shell test -e $(KBUILD_OUTPUT)$(KCONFIG_CONFIG) && \ > + $(srctree)/scripts/config \ > + --file $(KBUILD_OUTPUT)$(KCONFIG_CONFIG) \ > + --state "DEFAULT_ARCH") > +ifeq ($(filter-out undef,$(ARCH)),) > + ARCH := $(SUBARCH) > +endif > +endif > > # CROSS_COMPILE specify the prefix used for all executables used > # during compilation. Only gcc and related bin-utils executables > @@ -205,7 +218,6 @@ SUBARCH := $(shell uname -m | sed -e s/i.86/x86/ -e s/x86_64/x86/ \ > # "make" in the configured kernel build directory always uses that. > # Default value for CROSS_COMPILE is not to prefix executables > # Note: Some architectures assign CROSS_COMPILE in their arch/*/Makefile > -ARCH ?= $(SUBARCH) > CROSS_COMPILE ?= $(CONFIG_CROSS_COMPILE:"%"=%) > > # Architecture as present in compile.h > @@ -244,9 +256,6 @@ endif > # Where to locate arch specific headers > hdr-arch := $(SRCARCH) > > -KCONFIG_CONFIG ?= .config > -export KCONFIG_CONFIG > - > # SHELL used by kbuild > CONFIG_SHELL := $(shell if [ -x "$$BASH" ]; then echo $$BASH; \ > else if [ -x /bin/bash ]; then echo /bin/bash; \ > diff --git a/init/Kconfig b/init/Kconfig > index 9d76b99..3d58cb7 100644 > --- a/init/Kconfig > +++ b/init/Kconfig > @@ -2,6 +2,10 @@ config ARCH > string > option env="ARCH" > > +config DEFAULT_ARCH > + string > + default ARCH > + > config KERNELVERSION > string > option env="KERNELVERSION" Paul Bolle -- To unsubscribe from this list: send the line "unsubscribe linux-kbuild" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
