Re: [PATCH 2/4] tpm_tis: Fix interrupts for TIS TPMs without legacy cycles

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Sep 29, 2020 at 03:32:14PM -0700, James Bottomley wrote:
> If a TIS TPM doesn't have legacy cycles, any write to the interrupt
> registers is ignored unless a locality is active.  This means even to
> set up the interrupt vectors a locality must first be activated.  Fix
> this by activating the 0 locality in the interrupt probe setup.
> 
> Since the TPM_EOI signalling also requires an active locality, the
> interrupt routine cannot end an interrupt if the locality is released.
> This can lead to a situation where the TPM goes command ready after
> locality release and since the interrupt cannot be ended it refires
> continuously.  Fix this by disabling all interrupts except locality
> change when a locality is released (this only fires when a locality
> becomes active, meaning the TPM_EOI should work).
> 
> Finally, since we now disable all status based interrupts in the
> locality release, they must be re-enabled before waiting to check the
> condition, so add interrupt enabling to the status wait.
> 
> Signed-off-by: James Bottomley <James.Bottomley@xxxxxxxxxxxxxxxxxxxxx>
> ---
>  drivers/char/tpm/tpm_tis_core.c | 125 ++++++++++++++++++++++++++------
>  1 file changed, 101 insertions(+), 24 deletions(-)
> 
> diff --git a/drivers/char/tpm/tpm_tis_core.c b/drivers/char/tpm/tpm_tis_core.c
> index a9fa40714c64..02cc384fdaea 100644
> --- a/drivers/char/tpm/tpm_tis_core.c
> +++ b/drivers/char/tpm/tpm_tis_core.c
> @@ -29,6 +29,46 @@
>  
>  static void tpm_tis_clkrun_enable(struct tpm_chip *chip, bool value);
>  
> +static void enable_interrupt(struct tpm_chip *chip, u8 mask)

Even if this has not been followed before I'd prefeer that for new
functions or when modifying the signature of function they'd be
prefixed with tpm_tis_.

It is is just more practical e.g. for grepping stuff.

I'm fine with full 'interrupt' would but I also think that just
'int' would be perfectly fine. Not something I'm too opionated
about.

> +{
> +	struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
> +	u32 intmask;
> +
> +	/* Take control of the TPM's interrupt hardware and shut it off */
> +	tpm_tis_read32(priv, TPM_INT_ENABLE(priv->locality), &intmask);
> +
> +	intmask |= mask | TPM_GLOBAL_INT_ENABLE;
> +
> +	tpm_tis_write32(priv, TPM_INT_ENABLE(priv->locality), intmask);
> +}
> +
> +static void disable_interrupt(struct tpm_chip *chip, u8 mask)
> +{
> +	struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
> +	u32 intmask;
> +
> +	/* Take control of the TPM's interrupt hardware and shut it off */
> +	tpm_tis_read32(priv, TPM_INT_ENABLE(priv->locality), &intmask);
> +
> +	intmask &= ~mask;
> +
> +	tpm_tis_write32(priv, TPM_INT_ENABLE(priv->locality), intmask);
> +}
> +
> +static void enable_stat_interrupt(struct tpm_chip *chip, u8 stat)

I'd use plural (interrupts or ints).

> +{
> +	u32 mask = 0;
> +
> +	if (stat & TPM_STS_COMMAND_READY)
> +		mask |= TPM_INTF_CMD_READY_INT;
> +	if (stat & TPM_STS_VALID)
> +		mask |= TPM_INTF_STS_VALID_INT;
> +	if (stat & TPM_STS_DATA_AVAIL)
> +		mask |= TPM_INTF_DATA_AVAIL_INT;
> +
> +	enable_interrupt(chip, mask);
> +}
> +
>  static bool wait_for_tpm_stat_cond(struct tpm_chip *chip, u8 mask,
>  					bool check_cancel, bool *canceled)
>  {
> @@ -65,11 +105,14 @@ static int wait_for_tpm_stat(struct tpm_chip *chip, u8 mask,
>  		timeout = stop - jiffies;
>  		if ((long)timeout <= 0)
>  			return -ETIME;
> +		enable_stat_interrupt(chip, mask);
>  		rc = wait_event_interruptible_timeout(*queue,
>  			wait_for_tpm_stat_cond(chip, mask, check_cancel,
>  					       &canceled),
>  			timeout);
>  		if (rc > 0) {
> +			if (rc == 1)
> +				dev_err(&chip->dev, "Lost Interrupt waiting for TPM stat\n");
>  			if (canceled)
>  				return -ECANCELED;
>  			return 0;
> @@ -137,6 +180,28 @@ static bool check_locality(struct tpm_chip *chip, int l)
>  static int release_locality(struct tpm_chip *chip, int l)
>  {
>  	struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
> +	u32 int_status;
> +	int rc;
> +
> +	/*
> +	 * Note that once we relinquish the locality, all writes to
> +	 * the interrupt registers become ineffective meaning we can't
> +	 * do a TPM_EOI.  This means we must disable every interrupt
> +	 * except the locality change one to avoid interrupt
> +	 * storms.
> +	 */
> +	disable_interrupt(chip, TPM_INTF_CMD_READY_INT
> +			  | TPM_INTF_STS_VALID_INT
> +			  | TPM_INTF_DATA_AVAIL_INT);
> +
> +	rc = tpm_tis_read32(priv, TPM_INT_STATUS(priv->locality), &int_status);
> +	if (rc < 0)
> +		return rc;
> +
> +	/* Clear all pending */
> +	rc = tpm_tis_write32(priv, TPM_INT_STATUS(priv->locality), int_status);
> +	if (rc < 0)
> +		return rc;
>  
>  	tpm_tis_write8(priv, TPM_ACCESS(l), TPM_ACCESS_ACTIVE_LOCALITY);
>  
> @@ -163,12 +228,17 @@ static int request_locality(struct tpm_chip *chip, int l)
>  		timeout = stop - jiffies;
>  		if ((long)timeout <= 0)
>  			return -1;
> +
>  		rc = wait_event_interruptible_timeout(priv->int_queue,
>  						      (check_locality
>  						       (chip, l)),
>  						      timeout);
> -		if (rc > 0)
> +		if (rc > 1)
> +			return l;
> +		if (rc == 1) {
> +			dev_info(&chip->dev, "Lost Interrupt waiting for locality\n");
>  			return l;
> +		}
>  		if (rc == -ERESTARTSYS && freezing(current)) {
>  			clear_thread_flag(TIF_SIGPENDING);
>  			goto again;
> @@ -464,6 +534,10 @@ static int tpm_tis_send(struct tpm_chip *chip, u8 *buf, size_t len)
>  	irq = priv->irq;
>  	priv->irq = 0;
>  	chip->flags &= ~TPM_CHIP_FLAG_IRQ;
> +	enable_interrupt(chip, TPM_INTF_CMD_READY_INT
> +			 | TPM_INTF_LOCALITY_CHANGE_INT
> +			 | TPM_INTF_DATA_AVAIL_INT
> +			 | TPM_INTF_STS_VALID_INT);
>  	rc = tpm_tis_send_main(chip, buf, len);
>  	priv->irq = irq;
>  	chip->flags |= TPM_CHIP_FLAG_IRQ;
> @@ -718,7 +792,7 @@ static int tpm_tis_gen_interrupt(struct tpm_chip *chip)
>   * irq is seen then leave the chip setup for IRQ operation, otherwise reverse
>   * everything and leave in polling mode. Returns 0 on success.
>   */
> -static int tpm_tis_probe_irq_single(struct tpm_chip *chip, u32 intmask,
> +static int tpm_tis_probe_irq_single(struct tpm_chip *chip,
>  				    int flags, int irq)
>  {
>  	struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
> @@ -752,9 +826,11 @@ static int tpm_tis_probe_irq_single(struct tpm_chip *chip, u32 intmask,
>  	if (rc < 0)
>  		return rc;
>  
> -	/* Turn on */
> -	rc = tpm_tis_write32(priv, TPM_INT_ENABLE(priv->locality),
> -			     intmask | TPM_GLOBAL_INT_ENABLE);
> +	/*
> +	 * Turn on.  The locality change interrupt is the only one
> +	 * always enabled
> +	 */
> +	enable_interrupt(chip, TPM_INTF_LOCALITY_CHANGE_INT);
>  	if (rc < 0)
>  		return rc;
>  
> @@ -786,7 +862,7 @@ static int tpm_tis_probe_irq_single(struct tpm_chip *chip, u32 intmask,
>   * do not have ACPI/etc. We typically expect the interrupt to be declared if
>   * present.
>   */
> -static void tpm_tis_probe_irq(struct tpm_chip *chip, u32 intmask)
> +static void tpm_tis_probe_irq(struct tpm_chip *chip)
>  {
>  	struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
>  	u8 original_int_vec;
> @@ -800,11 +876,9 @@ static void tpm_tis_probe_irq(struct tpm_chip *chip, u32 intmask)
>  	if (!original_int_vec) {
>  		if (IS_ENABLED(CONFIG_X86))
>  			for (i = 3; i <= 15; i++)
> -				if (!tpm_tis_probe_irq_single(chip, intmask, 0,
> -							      i))
> +				if (!tpm_tis_probe_irq_single(chip, 0, i))
>  					return;
> -	} else if (!tpm_tis_probe_irq_single(chip, intmask, 0,
> -					     original_int_vec))
> +	} else if (!tpm_tis_probe_irq_single(chip, 0, original_int_vec))
>  		return;
>  }
>  
> @@ -1029,8 +1103,7 @@ int tpm_tis_core_init(struct device *dev, struct tpm_tis_data *priv, int irq,
>  		}
>  
>  		if (irq) {
> -			tpm_tis_probe_irq_single(chip, intmask, IRQF_SHARED,
> -						 irq);
> +			tpm_tis_probe_irq_single(chip, IRQF_SHARED, irq);
>  			if (!(chip->flags & TPM_CHIP_FLAG_IRQ)) {
>  				dev_err(&chip->dev, FW_BUG
>  					"TPM interrupt not working, polling instead\n");
> @@ -1038,7 +1111,7 @@ int tpm_tis_core_init(struct device *dev, struct tpm_tis_data *priv, int irq,
>  				disable_interrupts(chip);
>  			}
>  		} else {
> -			tpm_tis_probe_irq(chip, intmask);
> +			tpm_tis_probe_irq(chip);
>  		}
>  	}
>  
> @@ -1064,12 +1137,23 @@ EXPORT_SYMBOL_GPL(tpm_tis_core_init);
>  static void tpm_tis_reenable_interrupts(struct tpm_chip *chip)
>  {
>  	struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
> -	u32 intmask;
>  	int rc;
>  
>  	if (chip->ops->clk_enable != NULL)
>  		chip->ops->clk_enable(chip, true);
>  
> +	/*
> +	 * must have the locality before we can enable interrupts, so
> +	 * poll for the locality being ready
> +	 */
> +	chip->flags &= ~TPM_CHIP_FLAG_IRQ;
> +	if (request_locality(chip, 0) != 0) {
> +		dev_err(&chip->dev, "Failed to enable interrupts after suspend\n");
> +		goto out;
> +	}
> +	chip->flags |= TPM_CHIP_FLAG_IRQ;
> +
> +
>  	/* reenable interrupts that device may have lost or
>  	 * BIOS/firmware may have disabled
>  	 */
> @@ -1077,17 +1161,10 @@ static void tpm_tis_reenable_interrupts(struct tpm_chip *chip)
>  	if (rc < 0)
>  		goto out;
>  
> -	rc = tpm_tis_read32(priv, TPM_INT_ENABLE(priv->locality), &intmask);
> -	if (rc < 0)
> -		goto out;
> -
> -	intmask |= TPM_INTF_CMD_READY_INT
> -	    | TPM_INTF_LOCALITY_CHANGE_INT | TPM_INTF_DATA_AVAIL_INT
> -	    | TPM_INTF_STS_VALID_INT | TPM_GLOBAL_INT_ENABLE;
> +	enable_interrupt(chip, TPM_INTF_LOCALITY_CHANGE_INT);
>  
> -	tpm_tis_write32(priv, TPM_INT_ENABLE(priv->locality), intmask);
> -
> -out:
> + out:
> +	release_locality(chip, 0);
>  	if (chip->ops->clk_enable != NULL)
>  		chip->ops->clk_enable(chip, false);
>  
> -- 
> 2.28.0
> 

Agree with the change minus the cosmetic stuff that I mentioned.

/Jarko



[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [Linux Kernel]     [Linux Kernel Hardening]     [Linux NFS]     [Linux NILFS]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux SCSI]

  Powered by Linux