On Fri, Nov 15, 2024 at 05:10:55AM +0000, Xu, Even wrote: > > > > -----Original Message----- > > From: Bagas Sanjaya <bagasdotme@xxxxxxxxx> > > Sent: Friday, November 15, 2024 12:04 PM > > To: Xu, Even <even.xu@xxxxxxxxx>; jikos@xxxxxxxxxx; bentiss@xxxxxxxxxx; > > corbet@xxxxxxx; Aaron, Ma <aaron.ma@xxxxxxxxxxxxx> > > Cc: linux-input@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; linux- > > doc@xxxxxxxxxxxxxxx; Sun, Xinpeng <xinpeng.sun@xxxxxxxxx>; Srinivas > > Pandruvada <srinivas.pandruvada@xxxxxxxxxxxxxxx> > > Subject: Re: [PATCH v2 01/22] HID: THC: Add documentation > > > > On Thu, Nov 14, 2024 at 01:33:55PM +0800, Even Xu wrote: > > > +Touch Host Controller is the name of the IP block in PCH that interface with > > Touch Devices (ex: > > > +touchscreen, touchpad etc.). It is comprised of 3 key functional blocks: > > > +- A natively half-duplex Quad I/O capable SPI master > > > +- Low latency I2C interface to support HIDI2C compliant devices > > > +- A HW sequencer with RW DMA capability to system memory > > > > I see in my htmldocs output that the list above is long running paragraph instead. > > You are right, let me fix it in next version. OK. > > > > > > +When THC is configured to SPI mode, opcodes are used for determining the > > read/write IO mode. > > > +There are some OPCode examples for SPI IO mode:: > > > + > > > + +--------+---------------------------------+ > > > + | opcode | Corresponding SPI command | > > > + +========+=================================+ > > > + | 0x0B | Read Single I/O | > > > + +--------+---------------------------------+ > > > + | 0x02 | Write Single I/O | > > > + +--------+---------------------------------+ > > > + | 0xBB | Read Dual I/O | > > > + +--------+---------------------------------+ > > > + | 0xB2 | Write Dual I/O | > > > + +--------+---------------------------------+ > > > + | 0xEB | Read Quad I/O | > > > + +--------+---------------------------------+ > > > + | 0xE2 | Write Quad I/O | > > > + +--------+---------------------------------+ > > > + > > > <snipped>... > > > +When THC is working in I2C mode, opcodes are used to tell THC what's the > > next PIO type: > > > +I2C SubIP APB register read, I2C SubIP APB register write, I2C touch > > > +IC device read, I2C touch IC device write, I2C touch IC device write followed > > by read. > > > + > > > +Here are the THC pre-defined opcodes for I2C mode:: > > > + > > > + +--------+-------------------------------------------+----------+ > > > + | opcode | Corresponding I2C command | Address | > > > + > > +========+===========================================+==========+ > > > + | 0x12 | Read I2C SubIP APB internal registers | 0h - FFh | > > > + +--------+-------------------------------------------+----------+ > > > + | 0x13 | Write I2C SubIP APB internal registers | 0h - FFh | > > > + +--------+-------------------------------------------+----------+ > > > + | 0x14 | Read external Touch IC through I2C bus | N/A | > > > + +--------+-------------------------------------------+----------+ > > > + | 0x18 | Write external Touch IC through I2C bus | N/A | > > > + +--------+-------------------------------------------+----------+ > > > + | 0x1C | Write then read external Touch IC through | N/A | > > > + | | I2C bus | | > > > + +--------+-------------------------------------------+----------+ > > > + > > > <snipped>... > > > +Intel THC uses PRD entry descriptor for every PRD entry. Every PRD > > > +entry descriptor occupies > > > +128 bits memories:: > > > + > > > + +-------------------+---------+------------------------------------------------+ > > > + | struct field | bit(s) | description | > > > + > > +===================+=========+================================== > > === > > > + +===========+ > > > + | dest_addr | 53..0 | destination memory address, as every entry | > > > + | | | is 4KB, ignore lowest 10 bits of address. | > > > + +-------------------+---------+------------------------------------------------+ > > > + | reserved1 | 54..62 | reserved | > > > + +-------------------+---------+------------------------------------------------+ > > > + | int_on_completion | 63 | completion interrupt enable bit, if this bit | > > > + | | | set it means THC will trigger a completion | > > > + | | | interrupt. This bit is set by SW driver. | > > > + +-------------------+---------+------------------------------------------------+ > > > + | len | 87..64 | how many bytes of data in this entry. | > > > + +-------------------+---------+------------------------------------------------+ > > > + | end_of_prd | 88 | end of PRD table bit, if this bit is set, | > > > + | | | it means this entry is last entry in this PRD | > > > + | | | table. This bit is set by SW driver. | > > > + +-------------------+---------+------------------------------------------------+ > > > + | hw_status | 90..89 | HW status bits | > > > + +-------------------+---------+------------------------------------------------+ > > > + | reserved2 | 127..91 | reserved | > > > + +-------------------+---------+------------------------------------------------+ > > > > Shouldn't these tables be formatted as tables? > > Good idea! > Let's format them. Just drop the literal block formatting, keeping the table as-is. -- An old man doll... just what I always wanted! - Clara
Attachment:
signature.asc
Description: PGP signature
