Re: [PATCH v9 4/4] input: pm8xxx-vibrator: add new SPMI vibrator support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, 11 Apr 2024 at 11:32, Fenglin Wu via B4 Relay
<devnull+quic_fenglinw.quicinc.com@xxxxxxxxxx> wrote:
>
> From: Fenglin Wu <quic_fenglinw@xxxxxxxxxxx>
>
> Add support for a new SPMI vibrator module which is very similar
> to the vibrator module inside PM8916 but has a finer drive voltage
> step and different output voltage range, its drive level control
> is expanded across 2 registers. The vibrator module can be found
> in following Qualcomm PMICs: PMI632, PM7250B, PM7325B, PM7550BA.
>
> Signed-off-by: Fenglin Wu <quic_fenglinw@xxxxxxxxxxx>
> ---
>  drivers/input/misc/pm8xxx-vibrator.c | 51 +++++++++++++++++++++++++++++-------
>  1 file changed, 42 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/input/misc/pm8xxx-vibrator.c b/drivers/input/misc/pm8xxx-vibrator.c
> index 2959edca8eb9..35bb6f450fd2 100644
> --- a/drivers/input/misc/pm8xxx-vibrator.c
> +++ b/drivers/input/misc/pm8xxx-vibrator.c
> @@ -12,10 +12,10 @@
>  #include <linux/regmap.h>
>  #include <linux/slab.h>
>
> -#define VIB_MAX_LEVEL_mV       (3100)
> -#define VIB_MIN_LEVEL_mV       (1200)
> -#define VIB_PER_STEP_mV        (100)
> -#define VIB_MAX_LEVELS         (VIB_MAX_LEVEL_mV - VIB_MIN_LEVEL_mV + VIB_PER_STEP_mV)
> +#define VIB_MAX_LEVEL_mV(vib)  (vib->drv2_addr ? 3544 : 3100)
> +#define VIB_MIN_LEVEL_mV(vib)  (vib->drv2_addr ? 1504 : 1200)
> +#define VIB_PER_STEP_mV(vib)   (vib->drv2_addr ? 8 : 100)
> +#define VIB_MAX_LEVELS(vib)    (VIB_MAX_LEVEL_mV(vib) - VIB_MIN_LEVEL_mV(vib) + VIB_PER_STEP_mV(vib))
>
>  #define MAX_FF_SPEED           0xff
>
> @@ -26,6 +26,9 @@ struct pm8xxx_regs {
>         unsigned int drv_offset;
>         unsigned int drv_mask;
>         unsigned int drv_shift;
> +       unsigned int drv2_offset;
> +       unsigned int drv2_mask;
> +       unsigned int drv2_shift;
>         unsigned int drv_en_manual_mask;
>  };
>
> @@ -45,6 +48,18 @@ static struct pm8xxx_regs pm8916_regs = {
>         .drv_en_manual_mask = 0,
>  };
>
> +static struct pm8xxx_regs pmi632_regs = {
> +       .enable_offset = 0x46,
> +       .enable_mask = BIT(7),
> +       .drv_offset = 0x40,
> +       .drv_mask = GENMASK(7, 0),
> +       .drv_shift = 0,
> +       .drv2_offset = 0x41,
> +       .drv2_mask = GENMASK(3, 0),
> +       .drv2_shift = 8,
> +       .drv_en_manual_mask = 0,
> +};
> +
>  /**
>   * struct pm8xxx_vib - structure to hold vibrator data
>   * @vib_input_dev: input device supporting force feedback
> @@ -53,6 +68,7 @@ static struct pm8xxx_regs pm8916_regs = {
>   * @regs: registers' info
>   * @enable_addr: vibrator enable register
>   * @drv_addr: vibrator drive strength register
> + * @drv2_addr: vibrator drive strength upper byte register
>   * @speed: speed of vibration set from userland
>   * @active: state of vibrator
>   * @level: level of vibration to set in the chip
> @@ -65,6 +81,7 @@ struct pm8xxx_vib {
>         const struct pm8xxx_regs *regs;
>         unsigned int enable_addr;
>         unsigned int drv_addr;
> +       unsigned int drv2_addr;
>         int speed;
>         int level;
>         bool active;
> @@ -82,6 +99,10 @@ static int pm8xxx_vib_set(struct pm8xxx_vib *vib, bool on)
>         unsigned int val = vib->reg_vib_drv;
>         const struct pm8xxx_regs *regs = vib->regs;
>
> +       /* vibrator without drv2_addr needs be programmed in step increments */

How are these two items related? Are you using vib->drv2_addr as a
marker for 'particular generation'? In such a case please use a flag
instead.

The rest looks good to me.

> +       if (!vib->drv2_addr)
> +               vib->level /= VIB_PER_STEP_mV(vib);
> +
>         if (on)
>                 val |= (vib->level << regs->drv_shift) & regs->drv_mask;
>         else
> @@ -93,6 +114,17 @@ static int pm8xxx_vib_set(struct pm8xxx_vib *vib, bool on)
>
>         vib->reg_vib_drv = val;
>
> +       if (regs->drv2_mask) {
> +               if (on)
> +                       val = (vib->level << regs->drv2_shift) & regs->drv2_mask;
> +               else
> +                       val = 0;
> +
> +               rc = regmap_write_bits(vib->regmap, vib->drv2_addr, regs->drv2_mask, val);
> +               if (rc < 0)
> +                       return rc;
> +       }
> +
>         if (regs->enable_mask)
>                 rc = regmap_update_bits(vib->regmap, vib->enable_addr,
>                                         regs->enable_mask, on ? regs->enable_mask : 0);
> @@ -115,17 +147,16 @@ static void pm8xxx_work_handler(struct work_struct *work)
>                 return;
>
>         /*
> -        * pmic vibrator supports voltage ranges from 1.2 to 3.1V, so
> +        * pmic vibrator supports voltage ranges from MIN_LEVEL to MAX_LEVEL, so
>          * scale the level to fit into these ranges.
>          */
>         if (vib->speed) {
>                 vib->active = true;
> -               vib->level = ((VIB_MAX_LEVELS * vib->speed) / MAX_FF_SPEED) +
> -                                               VIB_MIN_LEVEL_mV;
> -               vib->level /= VIB_PER_STEP_mV;
> +               vib->level = VIB_MIN_LEVEL_mV(vib);
> +               vib->level += mult_frac(VIB_MAX_LEVELS(vib), vib->speed, MAX_FF_SPEED);
>         } else {
>                 vib->active = false;
> -               vib->level = VIB_MIN_LEVEL_mV / VIB_PER_STEP_mV;
> +               vib->level = VIB_MIN_LEVEL_mV(vib);
>         }
>
>         pm8xxx_vib_set(vib, vib->active);
> @@ -203,6 +234,7 @@ static int pm8xxx_vib_probe(struct platform_device *pdev)
>
>         vib->enable_addr = reg_base + regs->enable_offset;
>         vib->drv_addr = reg_base + regs->drv_offset;
> +       vib->drv2_addr = reg_base + regs->drv2_offset;
>
>         /* operate in manual mode */
>         error = regmap_read(vib->regmap, vib->drv_addr, &val);
> @@ -257,6 +289,7 @@ static const struct of_device_id pm8xxx_vib_id_table[] = {
>         { .compatible = "qcom,pm8058-vib", .data = &pm8058_regs },
>         { .compatible = "qcom,pm8921-vib", .data = &pm8058_regs },
>         { .compatible = "qcom,pm8916-vib", .data = &pm8916_regs },
> +       { .compatible = "qcom,pmi632-vib", .data = &pmi632_regs },
>         { }
>  };
>  MODULE_DEVICE_TABLE(of, pm8xxx_vib_id_table);
>
> --
> 2.25.1
>
>


-- 
With best wishes
Dmitry




[Index of Archives]     [Linux Media Devel]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Linux Wireless Networking]     [Linux Omap]

  Powered by Linux