On 12/6/2023 13:55, Rahul Rameshbabu wrote:
On Wed, 06 Dec, 2023 13:22:25 -0600 Mario Limonciello <mario.limonciello@xxxxxxx> wrote:
On 12/6/2023 12:46, Rahul Rameshbabu wrote:
On Wed, 06 Dec, 2023 11:58:18 -0600 Mario Limonciello <mario.limonciello@xxxxxxx> wrote:
The Framework 16" laptop doesn't have a PS/2 keyboard. At bootup the
following messages are emitted:
i8042: PNP: No PS/2 controller found.
i8042: PNP: Probing ports directly.
i8042: Can't read CTR while initializing i8042
i8042: probe of i8042 failed with error -5
The last two messages are ERR and WARN respectively. These messages
might be useful for one boot while diagnosing a problem for someone
but as there is no PS/2 controller in PNP or on the machine they're
needlessly noisy to emit every boot.
Downgrade the CTR message to debug and change the error code for the
failure so that the base device code doesn't emit a warning.
If someone has problems with i8042 and they need this information,
they can turn on dynamic debugging to get these messages.
Signed-off-by: Mario Limonciello <mario.limonciello@xxxxxxx>
---
For the Framework 16, I think the following should be done.
Use SERIO_QUIRK_NOPNP for the device to avoid the PS/2 controller
probing. You can find examples in drivers/input/serio/i8042-acpipnpio.h
under the i8042_dmi_quirk_table. This will prevent emitting the first
two messages in the shared snippet.
I had tried this initially, and yes those first two messages are removed. But
TBH I'm not too worried about those as they're INFO. Adding a quirk just
switches them over to a new INFO message.
Right, I can imagine someone owning this device panic-ing about the logs
in red/yellow in journalctl or dmesg output. That said, since we know
that the device should not bother with PNP, I think we should add the
quirk, none the less.
But the ERR and WARN messages still come up. The 3 messages that show up are:
i8042: PNP detection disabled
i8042: Can't read CTR while initializing i8042
i8042: probe of i8042 failed with error -5
I'm more concerned that ERR and WARN messages show up making you think there is
a problem to look into.
drivers/input/serio/i8042.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/input/serio/i8042.c b/drivers/input/serio/i8042.c
index 9fbb8d31575a..95dd585fdc1a 100644
--- a/drivers/input/serio/i8042.c
+++ b/drivers/input/serio/i8042.c
@@ -1008,8 +1008,8 @@ static int i8042_controller_init(void)
udelay(50);
if (i8042_command(&ctr[n++ % 2], I8042_CMD_CTL_RCTR)) {
- pr_err("Can't read CTR while initializing i8042\n");
- return i8042_probe_defer ? -EPROBE_DEFER : -EIO;
+ pr_debug("Can't read CTR while initializing\n");
I also think this error message should be pr_err in the situation that
the SERIO_QUIRK_PROBE_DEFER quirk is not used. I think what you are
likely looking for is avoiding emitting this message when the
SERIO_QUIRK_PROBE_DEFER quirk is used for noise reduction purposes.
SERIO_QUIRK_PROBE_DEFER isn't set on this machine.
Yeah, I would like to add this quirk as well for the device potentially
along with SERIO_QUIRK_NOPNP. I'll get into why I think this might be a
good idea later in this email.
OK if we end up with a quirk for this system in the end I'll add both.
+ return i8042_probe_defer ? -EPROBE_DEFER : -ENXIO;
I do not think this change makes sense to me personally. It is indeed an
I/O issue with the i8042 controller on the Framework motherboard, so the
error should be -EIO when i8042_probe_defer is not set.
With i8042.debug enabled I can see that the error is a wait read timeout. So I
had thought -ENXIO ("No such device or address") made sense here.
Right, I think that wait read timeout you are seeing is likely a symptom
of something very similar to the experience on laptops like the ASUS
ZenBook UX425UA, which inspired the introduction of the probe deferring
in the i8042 driver.
https://lore.kernel.org/lkml/20211112180022.10850-1-tiwai@xxxxxxx/T/
In this case though, the ASUS ZenBook device did have a PS/2 device
attached, while in the Framework device this shouldn't be the case. Will
delve more into this nuance in my next section.
OK let me experiment with this and get back on what happens.
If you feel strongly that the errors and warnings should stay as is I I wonder
if this should be looked at from i8042_pnp_init().
In the no PNP device declared case it still probes, why isn't PNP trusted?
My understanding is this is due to some PS/2 devices not supporting PNP
so this manual probe path must still be taken even when we add the
SERIO_QUIRK_NOPNP quirk. I think if we add the quirk for deferred
probing for the device, we can then also have a patch that does not omit
the error to the logs when this quirk is enabled.
My question now becomes the following. If the Framework device does not
want to expose its Intel 8042 controller to the host since its some
unused hardware on the mainboard, why does it bother to advertise the
8042 over the ACPI table? Wouldn't it be better to have some UEFI update
that fixes the ACPI table listing to avoid advertising the 8042?
https://wiki.osdev.org/%228042%22_PS/2_Controller
You hit on the head my confusion. The laptop doesn't advertise any of
the PNP IDs listed in pnp_kbd_devids.
I double checked in /sys/bus/acpi/devices.
It seems that they're ignored anyway and will probe whether they are
there or not.
So how could the firmware actually advertise this so the kernel would
trust it?
}
} while (n < 2 || ctr[0] != ctr[1]);
--
Thanks,
Rahul Rameshbabu
