Re: [RFC PATCH v3 3/5] platform/chrome: Introduce device tree hardware prober

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Nov 29, 2023 at 12:26 AM Andy Shevchenko
<andriy.shevchenko@xxxxxxxxxxxxxxx> wrote:
>
> On Tue, Nov 28, 2023 at 04:42:32PM +0800, Chen-Yu Tsai wrote:
> > Some devices are designed and manufactured with some components having
> > multiple drop-in replacement options. These components are often
> > connected to the mainboard via ribbon cables, having the same signals
> > and pin assignments across all options. These may include the display
> > panel and touchscreen on laptops and tablets, and the trackpad on
> > laptops. Sometimes which component option is used in a particular device
> > can be detected by some firmware provided identifier, other times that
> > information is not available, and the kernel has to try to probe each
> > device.
> >
> > This change attempts to make the "probe each device" case cleaner. The
> > current approach is to have all options added and enabled in the device
> > tree. The kernel would then bind each device and run each driver's probe
> > function. This works, but has been broken before due to the introduction
> > of asynchronous probing, causing multiple instances requesting "shared"
> > resources, such as pinmuxes, GPIO pins, interrupt lines, at the same
> > time, with only one instance succeeding. Work arounds for these include
> > moving the pinmux to the parent I2C controller, using GPIO hogs or
> > pinmux settings to keep the GPIO pins in some fixed configuration, and
> > requesting the interrupt line very late. Such configurations can be seen
> > on the MT8183 Krane Chromebook tablets, and the Qualcomm sc8280xp-based
> > Lenovo Thinkpad 13S.
> >
> > Instead of this delicate dance between drivers and device tree quirks,
> > this change introduces a simple I2C component prober. For any given
> > class of devices on the same I2C bus, it will go through all of them,
> > doing a simple I2C read transfer and see which one of them responds.
> > It will then enable the device that responds.
> >
> > This requires some minor modifications in the existing device tree.
> > The status for all the device nodes for the component options must be
> > set to "failed-needs-probe". This makes it clear that some mechanism is
> > needed to enable one of them, and also prevents the prober and device
> > drivers running at the same time.
>
> ...
>
> > +#include <linux/array_size.h>
> > +#include <linux/i2c.h>
> > +#include <linux/of.h>
> > +#include <linux/platform_device.h>
>
> init.h for init calls.

Added to next version.

> > +static int chromeos_of_hw_prober_probe(struct platform_device *pdev)
> > +{
> > +     for (size_t i = 0; i < ARRAY_SIZE(hw_prober_platforms); i++)
> > +             if (of_machine_is_compatible(hw_prober_platforms[i].compatible)) {
> > +                     int ret;
>
> Perhaps
>
>                 if (!of_machine_is_compatible(hw_prober_platforms[i].compatible))
>                         continue;
>
> ?

Works for me. One less level of indentation.

Thanks
ChenYu

> > +                     ret = hw_prober_platforms[i].prober(&pdev->dev,
> > +                                                         hw_prober_platforms[i].data);
> > +                     if (ret)
> > +                             return ret;
> > +             }
> > +
> > +     return 0;
> > +}
>
> --
> With Best Regards,
> Andy Shevchenko
>
>





[Index of Archives]     [Linux Media Devel]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Linux Wireless Networking]     [Linux Omap]

  Powered by Linux