The Himax HID-over-SPI framework support for Himax touchscreen ICs that report HID packet through SPI bus. The driver core need reset pin to meet reset timing spec. of IC. An interrupt to disable and enable interrupt when suspend/resume. Two optional power control if target board needed. Signed-off-by: Tylor Yang <tylor_yang@xxxxxxxxxxxxxxxxxxxxxxxxxxxxx> --- .../devicetree/bindings/input/himax,hid.yaml | 123 ++++++++++++++++++ MAINTAINERS | 6 + 2 files changed, 129 insertions(+) create mode 100644 Documentation/devicetree/bindings/input/himax,hid.yaml diff --git a/Documentation/devicetree/bindings/input/himax,hid.yaml b/Documentation/devicetree/bindings/input/himax,hid.yaml new file mode 100644 index 000000000000..9ba86fe1b7da --- /dev/null +++ b/Documentation/devicetree/bindings/input/himax,hid.yaml @@ -0,0 +1,123 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/himax,hid.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Himax TDDI devices using SPI to send HID packets + +maintainers: + - Tylor Yang <tylor_yang@xxxxxxxxxxxxxxxxxxxxxxxxxxxxx> + +description: | + Support the Himax TDDI devices which using SPI interface to acquire + HID packets from the device. The device needs to be initialized using + Himax protocol before it start sending HID packets. + +properties: + compatible: + const: himax,hid + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset: + maxItems: 1 + description: Reset device, active low signal. + + vccd-supply: + description: + Optional regulator for the 1.8V voltage. + + vcca-supply: + description: + Optional regulator for the analog 3.3V voltage. + + himax,id-gpios: + maxItems: 8 + description: GPIOs to read physical Panel ID. Optional. + + spi-cpha: true + spi-cpol: true + + himax,ic-det-delay-ms: + description: + Due to TDDI properties, the TPIC detection timing must after the + display panel initialized. This property is used to specify the + delay time when TPIC detection and display panel initialization + timing are overlapped. How much milliseconds to delay before TPIC + detection start. + + himax,ic-resume-delay-ms: + description: + Due to TDDI properties, the TPIC resume timing must after the + display panel resumed. This property is used to specify the + delay time when TPIC resume and display panel resume + timing are overlapped. How much milliseconds to delay before TPIC + resume start. + + panel: + description: + The node of the display panel device. The driver will use this + node to get the project ID of the display panel. Optional. + type: object + additionalProperties: false + + properties: + himax,pid: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 65535 + description: + When only one value exist, represent Project ID of the device. + When multiple values exist, order in event number value represnet + id value from id-gpios and odd number value represent Project ID + relatives to prior id value. This is used to specify the firmware + for the device. + + required: + - himax,pid + +required: + - compatible + - reg + - interrupts + - reset + +unevaluatedProperties: false + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@0 { + compatible = "himax,hid"; + reg = <0x0>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&touch_pins>; + pinctrl-names = "default"; + + spi-max-frequency = <12500000>; + spi-cpha; + spi-cpol; + + reset = <&gpio1 8 GPIO_ACTIVE_LOW>; + himax,ic-det-delay-ms = <500>; + himax,ic-resume-delay-ms = <100>; + }; + }; diff --git a/MAINTAINERS b/MAINTAINERS index 7a7bd8bd80e9..883870ab316f 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -9340,6 +9340,12 @@ L: linux-kernel@xxxxxxxxxxxxxxx S: Maintained F: drivers/misc/hisi_hikey_usb.c +HIMAX HID OVER SPI TOUCHSCREEN SUPPORT +M: Tylor Yang <tylor_yang@xxxxxxxxxxxxxxxxxxxxxxxxxxxxx> +L: linux-input@xxxxxxxxxxxxxxx +S: Supported +F: Documentation/devicetree/bindings/input/himax,hid.yaml + HIMAX HX83112B TOUCHSCREEN SUPPORT M: Job Noorman <job@xxxxxxxxxxxx> L: linux-input@xxxxxxxxxxxxxxx -- 2.25.1
