On Fri, Oct 6, 2023 at 3:45 PM Duje Mihanović <duje.mihanovic@xxxxxxxx> wrote:
>
> Sharp's Spitz board still uses the legacy GPIO interface for controlling
> a GPIO pin related to the USB host controller.
>
> Convert this function to use the new GPIO descriptor interface.
>
> Reviewed-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
> Signed-off-by: Duje Mihanović <duje.mihanovic@xxxxxxxx>
> ---
> arch/arm/mach-pxa/spitz.c | 13 ++++++-------
> drivers/usb/host/ohci-pxa27x.c | 7 +++++++
> 2 files changed, 13 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
> index cc691b199429..535e2b2e997b 100644
> --- a/arch/arm/mach-pxa/spitz.c
> +++ b/arch/arm/mach-pxa/spitz.c
> @@ -649,23 +649,22 @@ static inline void spitz_mmc_init(void) {}
> * USB Host
> ******************************************************************************/
> #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
> +GPIO_LOOKUP_SINGLE(spitz_usb_host_gpio_table, "pxa27x-ohci", "gpio-pxa",
> + SPITZ_GPIO_USB_HOST, "usb-host", GPIO_ACTIVE_LOW);
> +
> static int spitz_ohci_init(struct device *dev)
> {
> - int err;
> -
> - err = gpio_request(SPITZ_GPIO_USB_HOST, "USB_HOST");
> - if (err)
> - return err;
> + gpiod_add_lookup_table(&spitz_usb_host_gpio_table);
>
> /* Only Port 2 is connected, setup USB Port 2 Output Control Register */
> UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
>
> - return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1);
> + return 0;
> }
>
> static void spitz_ohci_exit(struct device *dev)
> {
> - gpio_free(SPITZ_GPIO_USB_HOST);
> + gpiod_remove_lookup_table(&spitz_usb_host_gpio_table);
> }
>
> static struct pxaohci_platform_data spitz_ohci_platform_data = {
> diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
> index 357d9aee38a3..7f04421c80d6 100644
> --- a/drivers/usb/host/ohci-pxa27x.c
> +++ b/drivers/usb/host/ohci-pxa27x.c
> @@ -121,6 +121,7 @@ struct pxa27x_ohci {
> void __iomem *mmio_base;
> struct regulator *vbus[3];
> bool vbus_enabled[3];
> + struct gpio_desc *usb_host;
> };
>
> #define to_pxa27x_ohci(hcd) (struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv)
> @@ -447,6 +448,10 @@ static int ohci_hcd_pxa27x_probe(struct platform_device *pdev)
> pxa_ohci = to_pxa27x_ohci(hcd);
> pxa_ohci->clk = usb_clk;
> pxa_ohci->mmio_base = (void __iomem *)hcd->regs;
> + pxa_ohci->usb_host = devm_gpiod_get_optional(&pdev->dev, "usb-host", GPIOD_OUT_LOW);
> + if (IS_ERR(pxa_ohci->usb_host))
> + return dev_err_probe(&pdev->dev, PTR_ERR(pxa_ohci->usb_host),
> + "failed to get USB host GPIO\n");
>
> for (i = 0; i < 3; ++i) {
> char name[6];
> @@ -512,6 +517,8 @@ static void ohci_hcd_pxa27x_remove(struct platform_device *pdev)
> for (i = 0; i < 3; ++i)
> pxa27x_ohci_set_vbus_power(pxa_ohci, i, false);
>
> + gpiod_put(pxa_ohci->usb_host);
This is now wrong. Devres APIs are managed by the driver core. You no
longer need this in your remove() callback.
Bart
> +
> usb_put_hcd(hcd);
> }
>
>
> --
> 2.42.0
>
>
