Re: [PATCH v2 1/4] dt-bindings: input: Add CP2112 HID USB to SMBus Bridge

[Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>]

On 04/02/2023 05:43, Danny Kaehn wrote:
> This is a USB HID device which includes an I2C controller and 8 GPIO pins.
> 
> The binding allows describing the chip's gpio and i2c controller in DT
> using the subnodes named "gpio" and "i2c", respectively. This is
> intended to be used in configurations where the CP2112 is permanently
> connected in hardware.
> 
> Signed-off-by: Danny Kaehn <kaehndan@xxxxxxxxx>
> ---
>  .../bindings/input/silabs,cp2112.yaml         | 114 ++++++++++++++++++
>  1 file changed, 114 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/input/silabs,cp2112.yaml
> 
> diff --git a/Documentation/devicetree/bindings/input/silabs,cp2112.yaml b/Documentation/devicetree/bindings/input/silabs,cp2112.yaml
> new file mode 100644
> index 000000000000..a8d7f8aea6c2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/input/silabs,cp2112.yaml
> @@ -0,0 +1,114 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/input/silabs,cp2112.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: CP2112 HID USB to SMBus/I2C Bridge
> +
> +maintainers:
> +  - Danny Kaehn <kaehndan@xxxxxxxxx>
> +
> +description:
> +  The CP2112 is a USB HID device which includes an integrated I2C controller
> +  and 8 GPIO pins. Its GPIO pins can each be configured as inputs, open-drain
> +  outputs, or push-pull outputs.
> +
> +properties:
> +  compatible:
> +    const: usb10c4,ea90
> +
> +  reg:
> +    maxItems: 1
> +    description: The USB port number on the host controller
> +
> +  i2c:
> +    description: The SMBus/I2C controller node for the CP2112
> +    $ref: /schemas/i2c/i2c-controller.yaml#

on this level: unevaluatedProperties: false

> +
> +    properties:
> +      clock-frequency:
> +        minimum: 10000
> +        default: 100000
> +        maximum: 400000
> +
> +  gpio:
> +    description: The GPIO controller node for the CP2112
> +    $ref: /schemas/gpio/gpio.yaml#

Drop it, it's always selected.

> +
> +    properties:
> +      interrupt-controller: true
> +      '#interrupt-cells':
> +        const: 2
> +
> +      gpio-controller: true
> +      "#gpio-cells":

Keep consistent quotes - either ' or "

> +        const: 2
> +
> +      ngpios:
> +        const: 8
> +
> +    patternProperties:
> +      "^(hog-[0-9]+|.+-hog(-[0-9]+)?)$":
> +        type: object
> +        properties:
> +          gpio-hog: true
> +          gpios: true

minItems: 1
maxItems: 8

> +          input: true
> +          output-high: true
> +          output-low: true
> +          line-name: true
> +
> +        required:
> +          - gpio-hog
> +          - gpios
> +
> +        additionalProperties: false
> +
> +    unevaluatedProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/input/input.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    usb {
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +
> +      device@1 {
> +        compatible = "usb10c4,ea90";
> +        reg = <1>;
> +
> +        i2c {
> +          #address-cells = <1>;
> +          #size-cells = <0>;
> +
> +          temp@48 {
> +            compatible = "national,lm75";
> +            reg = <0x48>;
> +          };
> +        };
> +
> +        gpio {
> +          gpio-controller;
> +          interrupt-controller;
> +          #gpio-cells = <2>;
> +          gpio-line-names =
> +            "TEST0",

Don't break it - should be with gpio-line-names. Align the rest of entries.

> +            "TEST1",
> +            "TEST2",
> +            "TEST3",
> +            "TEST4",
> +            "TEST5",
> +            "TEST6",
> +            "TEST7";
> +        };
> +      };
> +    };

Best regards,
Krzysztof