On Wed, Oct 26, 2022 at 14:24, Chris Morgan <macromorgan@xxxxxxxxxxx> wrote:
> On Fri, Oct 21, 2022 at 03:56:29PM +0200, Mattijs Korpershoek wrote:
>> Hi Chris,
>>
>> Thank you for your patch.
>>
>> On Mon, Oct 10, 2022 at 10:35, Chris Morgan <macroalpha82@xxxxxxxxx> wrote:
>>
>> > From: Chris Morgan <macromorgan@xxxxxxxxxxx>
>> >
>> > Add support for the Hynitron cst3xx controller found on devices such
>> > as the Anbernic RG353P and RG353V (the Hynitron CST340). This driver
>> > was built from sources provided by Hynitron to Anbernic (possibly
>> > via Rockchip as an intermediary) and marked as GPLv2 in the code.
>> > This driver was written strictly for the cst3xx series, but in
>> > most places was left somewhat generic so support could be easily
>> > added to other devices in the future.
>> >
>> > Signed-off-by: Chris Morgan <macromorgan@xxxxxxxxxxx>
>> > ---
>> > drivers/input/touchscreen/Kconfig | 12 +
>> > drivers/input/touchscreen/Makefile | 1 +
>> > drivers/input/touchscreen/hynitron_cstxxx.c | 508 ++++++++++++++++++++
>> > 3 files changed, 521 insertions(+)
>> > create mode 100644 drivers/input/touchscreen/hynitron_cstxxx.c
>> >
>> > diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
>> > index 2d70c945b20a..9a9528e59c36 100644
>> > --- a/drivers/input/touchscreen/Kconfig
>> > +++ b/drivers/input/touchscreen/Kconfig
>> > @@ -422,6 +422,18 @@ config TOUCHSCREEN_HYCON_HY46XX
>> > To compile this driver as a module, choose M here: the
>> > module will be called hycon-hy46xx.
>> >
>> > +config TOUCHSCREEN_HYNITRON_CSTXXX
>> > + tristate "Hynitron touchscreen support"
>> > + depends on I2C
>>
>> Since we include linux/of.h, I think we should also add:
>> depends on OF
>
> Thank you, will do and resubmit.
>
>>
>> There are some small nitpicks below as well.
>>
>> With those addressed, please add:
>>
>> Reviewed-by: Mattijs Korpershoek <mkorpershoek@xxxxxxxxxxxx>
>>
>> > + help
>> > + Say Y here if you have a touchscreen using a Hynitron
>> > + touchscreen controller.
>> > +
>> > + If unsure, say N.
>> > +
>> > + To compile this driver as a module, choose M here: the
>> > + module will be called hynitron-cstxxx.
>> > +
>> > config TOUCHSCREEN_ILI210X
>> > tristate "Ilitek ILI210X based touchscreen"
>> > depends on I2C
>> > diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
>> > index 557f84fd2075..43860ca19b98 100644
>> > --- a/drivers/input/touchscreen/Makefile
>> > +++ b/drivers/input/touchscreen/Makefile
>> > @@ -47,6 +47,7 @@ obj-$(CONFIG_TOUCHSCREEN_EXC3000) += exc3000.o
>> > obj-$(CONFIG_TOUCHSCREEN_FUJITSU) += fujitsu_ts.o
>> > obj-$(CONFIG_TOUCHSCREEN_GOODIX) += goodix_ts.o
>> > obj-$(CONFIG_TOUCHSCREEN_HIDEEP) += hideep.o
>> > +obj-$(CONFIG_TOUCHSCREEN_HYNITRON_CSTXXX) += hynitron_cstxxx.o
>> > obj-$(CONFIG_TOUCHSCREEN_ILI210X) += ili210x.o
>> > obj-$(CONFIG_TOUCHSCREEN_ILITEK) += ilitek_ts_i2c.o
>> > obj-$(CONFIG_TOUCHSCREEN_IMAGIS) += imagis.o
>> > diff --git a/drivers/input/touchscreen/hynitron_cstxxx.c b/drivers/input/touchscreen/hynitron_cstxxx.c
>> > new file mode 100644
>> > index 000000000000..11701ff39eb1
>> > --- /dev/null
>> > +++ b/drivers/input/touchscreen/hynitron_cstxxx.c
>> > @@ -0,0 +1,508 @@
>> > +// SPDX-License-Identifier: GPL-2.0-only
>> > +/*
>> > + * Driver for Hynitron cstxxx Touchscreen
>> > + *
>> > + * Copyright (c) 2022 Chris Morgan <macromorgan@xxxxxxxxxxx>
>> > + *
>> > + * This code is based on hynitron_core.c authored by Hynitron.
>> > + * Note that no datasheet was available, so much of these registers
>> > + * are undocumented. This is essentially a cleaned-up version of the
>> > + * vendor driver with support removed for hardware I cannot test and
>> > + * device-specific functions replated with generic functions wherever
>> > + * possible.
>> > + */
>> > +
>> > +#include <asm/unaligned.h>
>> > +#include <linux/delay.h>
>> > +#include <linux/gpio.h>
>> > +#include <linux/i2c.h>
>> > +#include <linux/input.h>
>> > +#include <linux/input/mt.h>
>> > +#include <linux/input/touchscreen.h>
>> > +#include <linux/module.h>
>> > +#include <linux/of.h>
>> > +#include <linux/of_device.h>
>> > +
>> > +/* Per chip data */
>> > +struct hynitron_ts_chip_data {
>> > + unsigned int max_touch_num;
>> > + u32 ic_chkcode;
>> > + int (*firmware_info)(struct i2c_client *client);
>> > + int (*bootloader_enter)(struct i2c_client *client);
>> > + int (*init_input)(struct i2c_client *client);
>> > + void (*report_touch)(struct i2c_client *client);
>> > +};
>> > +
>> > +/* Data generic to all (supported and non-supported) controllers. */
>> > +struct hynitron_ts_data {
>> > + const struct hynitron_ts_chip_data *pdata;
>> > + struct i2c_client *client;
>> > + struct input_dev *input_dev;
>> > + struct touchscreen_properties prop;
>> > + struct gpio_desc *reset_gpio;
>> > + struct gpio_desc *irq_gpio;
>> > +};
>> > +
>> > +/*
>> > + * Since I have no datasheet, these values are guessed and/or assumed
>> > + * based on observation and testing.
>> > + */
>> > +#define CST3XX_FIRMWARE_INFO_START_CMD 0x01d1
>> > +#define CST3XX_FIRMWARE_INFO_END_CMD 0x09d1
>> > +#define CST3XX_FIRMWARE_CHK_CODE_REG 0xfcd1
>> > +#define CST3XX_FIRMWARE_VERSION_REG 0x08d2
>> > +#define CST3XX_FIRMWARE_VER_INVALID_VAL 0xa5a5a5a5
>> > +
>> > +#define CST3XX_BOOTLDR_PROG_CMD 0xaa01a0
>> > +#define CST3XX_BOOTLDR_PROG_CHK_REG 0x02a0
>> > +#define CST3XX_BOOTLDR_CHK_VAL 0xac
>> > +
>> > +#define CST3XX_TOUCH_DATA_PART_REG 0x00d0
>> > +#define CST3XX_TOUCH_DATA_FULL_REG 0x07d0
>> > +#define CST3XX_TOUCH_DATA_CHK_VAL 0xab
>> > +#define CST3XX_TOUCH_DATA_TOUCH_VAL 0x03
>> > +#define CST3XX_TOUCH_DATA_STOP_CMD 0xab00d0
>> > +#define CST3XX_TOUCH_COUNT_MASK GENMASK(6, 0)
>> > +
>> > +
>> > +/*
>> > + * Hard coded reset delay value of 20ms not IC dependent in
>> > + * vendor driver.
>> > + */
>> > +static void hyn_reset_proc(struct i2c_client *client, int delay)
>> > +{
>> > + struct hynitron_ts_data *ts_data = i2c_get_clientdata(client);
>> > +
>> > + gpiod_set_value_cansleep(ts_data->reset_gpio, 1);
>> > + mdelay(20);
>> > + gpiod_set_value_cansleep(ts_data->reset_gpio, 0);
>> > + if (delay)
>> > + mdelay(delay);
>> > +}
>> > +
>> > +static irqreturn_t hyn_interrupt_handler(int irq, void *dev_id)
>> > +{
>> > + struct i2c_client *client = dev_id;
>> > + struct hynitron_ts_data *ts_data = i2c_get_clientdata(client);
>> > +
>> > + ts_data->pdata->report_touch(client);
>> > +
>> > + return IRQ_HANDLED;
>> > +}
>> > +
>> > +/*
>> > + * The vendor driver would retry twice before failing to read or write
>> > + * to the i2c device.
>> > + */
>> > +
>> > +static int cst3xx_i2c_write(struct i2c_client *client,
>> > + unsigned char *buf, int len)
>> > +{
>> > + int ret;
>> > + int retries = 0;
>> > +
>> > + while (retries < 2) {
>> > + ret = i2c_master_send(client, buf, len);
>> > + if (ret == len)
>> > + return 0;
>> > + if (ret <= 0)
>> > + retries++;
>> > + else
>> > + break;
>> > + }
>> > +
>> > + return ret < 0 ? ret : -EIO;
>> > +}
>> > +
>> > +static int cst3xx_i2c_read_register(struct i2c_client *client, u16 reg,
>> > + u8 *val, u16 len)
>> > +{
>> > + __le16 buf = cpu_to_le16(reg);
>> > + struct i2c_msg msgs[] = {
>> > + {
>> > + .addr = client->addr,
>> > + .flags = 0,
>> > + .len = 2,
>> > + .buf = (u8 *)&buf,
>> > + },
>> > + {
>> > + .addr = client->addr,
>> > + .flags = I2C_M_RD,
>> > + .len = len,
>> > + .buf = val,
>> > + }
>> > + };
>> > + int ret;
>> > +
>> > + ret = i2c_transfer(client->adapter, msgs, 2);
>> > + if (ret >= 0)
>> > + ret = (ret == ARRAY_SIZE(msgs) ? 0 : -EIO);
>> > +
>> > + if (ret)
>> > + dev_err(&client->dev,
>> > + "Error reading %d bytes from 0x%04x: %d\n",
>> > + len, reg, ret);
>>
>> This could be a single line, since column limit is 100chars now. This
>> applies for a lot of other wrapped lines in this file.
>>
>> Please consider joining such lines to reduce the overall line count.
>
> I want to confirm everyone else is okay with this change. While the
> column limit was changed to 100, some subsystems still prefer the old
> 80 limit. If everyone is okay with 100 I can do that, I just want to
> be sure.
I think it's fine:
$ find drivers/input -name '*.c' -exec wc -L {} + | sort -rh
198 total
198 drivers/input/mouse/synaptics.c
182 drivers/input/serio/i8042.c
167 drivers/input/keyboard/applespi.c
152 drivers/input/mouse/alps.c
151 drivers/input/mouse/elantech.c
133 drivers/input/mouse/elan_i2c_core.c
133 drivers/input/joystick/grip.c
133 drivers/input/joystick/adi.c
132 drivers/input/joystick/gf2k.c
132 drivers/input/joystick/gamecon.c
131 drivers/input/joystick/a3d.c
130 drivers/input/joystick/cobra.c
// ... snipp ...
I've also had some review on this on a previous driver i submitted here:
https://lore.kernel.org/all/YfK4UcuCfF7JfI7H@xxxxxxxxxxxxxxxxxx/
But let's wait for others to chime in. Again, this is more of a nitpick
so if you'd prefer to keep at 80chars that's fine to me as well.
Thanks
Mattijs
>
>>
>> > +
>> > + return ret;
>> > +}
>> > +
>> > +static int cst3xx_firmware_info(struct i2c_client *client)
>> > +{
>> > + struct hynitron_ts_data *ts_data = i2c_get_clientdata(client);
>> > + int ret;
>> > + u32 tmp;
>> > + unsigned char buf[4];
>> > +
>> > + /*
>> > + * Tests suggest this command needed to read firmware regs.
>> > + */
>> > + put_unaligned_le16(CST3XX_FIRMWARE_INFO_START_CMD, buf);
>> > + ret = cst3xx_i2c_write(client, buf, 2);
>> > + if (ret < 0)
>> > + return -EIO;
>> > +
>> > + mdelay(10);
>> > +
>> > + /*
>> > + * Read register for check-code to determine if device detected
>> > + * correctly.
>> > + */
>> > + ret = cst3xx_i2c_read_register(client, CST3XX_FIRMWARE_CHK_CODE_REG,
>> > + buf, 4);
>> > + if (ret < 0)
>> > + return -EIO;
>> > +
>> > + tmp = get_unaligned_le32(buf);
>> > + if ((tmp & 0xffff0000) != ts_data->pdata->ic_chkcode) {
>> > + dev_err(&client->dev, "%s ic mismatch\n", __func__);
>>
>> Should we print the device's ic_chkcode in case we don't recognize it?
>>
>
> Good idea, I'll make that change.
>
>> > + return -ENODEV;
>> > + }
>> > +
>> > + mdelay(10);
>> > +
>> > + /* Read firmware version and test if firmware missing. */
>> > + ret = cst3xx_i2c_read_register(client, CST3XX_FIRMWARE_VERSION_REG,
>> > + buf, 4);
>> > + if (ret < 0)
>> > + return -EIO;
>> > +
>> > + tmp = get_unaligned_le32(buf);
>> > + if (tmp == CST3XX_FIRMWARE_VER_INVALID_VAL) {
>> > + dev_err(&client->dev, "Device firmware missing\n");
>> > + return -ENODEV;
>> > + }
>> > +
>> > + /*
>> > + * Tests suggest cmd required to exit reading firmware regs.
>> > + */
>> > + put_unaligned_le16(CST3XX_FIRMWARE_INFO_END_CMD, buf);
>> > + ret = cst3xx_i2c_write(client, buf, 2);
>> > + if (ret < 0)
>> > + return -EIO;
>> > +
>> > + mdelay(5);
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +static int cst3xx_bootloader_enter(struct i2c_client *client)
>> > +{
>> > + int ret;
>> > + u8 retry;
>> > + u32 tmp;
>> > + unsigned char buf[3];
>> > +
>> > + for (retry = 0; retry < 5; retry++) {
>> > + hyn_reset_proc(client, (7 + retry));
>> > + /* set cmd to enter program mode */
>> > + put_unaligned_le24(CST3XX_BOOTLDR_PROG_CMD, buf);
>> > + ret = cst3xx_i2c_write(client, buf, 3);
>> > + if (ret < 0)
>> > + continue;
>> > + mdelay(2);
>> > +
>> > + /* check whether in program mode */
>> > + ret = cst3xx_i2c_read_register(client,
>> > + CST3XX_BOOTLDR_PROG_CHK_REG,
>> > + buf, 1);
>> > + tmp = get_unaligned(buf);
>> > +
>> > + if (ret < 0)
>> > + continue;
>> > +
>> > + if (tmp == CST3XX_BOOTLDR_CHK_VAL)
>> > + break;
>> > + }
>> > +
>> > + if (tmp != CST3XX_BOOTLDR_CHK_VAL) {
>> > + dev_err(&client->dev, "%s unable to enter bootloader mode\n",
>> > + __func__);
>> > + return -ENODEV;
>> > + }
>> > +
>> > + hyn_reset_proc(client, 40);
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +static void cst3xx_touch_update(struct hynitron_ts_data *ts_data,
>> > + s32 id, s32 x, s32 y, s32 w)
>> > +{
>> > + input_mt_slot(ts_data->input_dev, id);
>> > + input_mt_report_slot_state(ts_data->input_dev, MT_TOOL_FINGER, 1);
>> > + touchscreen_report_pos(ts_data->input_dev, &ts_data->prop, x, y, true);
>> > + input_report_abs(ts_data->input_dev, ABS_MT_TOUCH_MAJOR, w);
>> > +}
>> > +
>> > +static int cst3xx_finish_touch_read(struct i2c_client *client)
>> > +{
>> > + unsigned char buf[3];
>> > + int err;
>> > +
>> > + put_unaligned_le24(CST3XX_TOUCH_DATA_STOP_CMD, buf);
>> > + err = cst3xx_i2c_write(client, buf, 3);
>> > + if (err < 0) {
>> > + dev_err(&client->dev, "send read touch info ending failed.\n");
>> > + return err;
>> > + }
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +/*
>> > + * Handle events from IRQ. Note that for cst3xx it appears that IRQ
>> > + * fires continuously while touched, otherwise once every 1500ms
>> > + * when not touched (assume touchscreen waking up periodically).
>> > + * Note buffer is sized for 5 fingers, if more needed buffer must
>> > + * be increased. The buffer contains 5 bytes for each touch point,
>> > + * a touch count byte, a check byte, and then a second check byte after
>> > + * all other touch points.
>> > + *
>> > + * For example 1 touch would look like this:
>> > + * touch1[5]:touch_count[1]:chk_byte[1]
>> > + *
>> > + * 3 touches would look like this:
>> > + * touch1[5]:touch_count[1]:chk_byte[1]:touch2[5]:touch3[5]:chk_byte[1]
>> > + */
>> > +static void cst3xx_touch_report(struct i2c_client *client)
>> > +{
>> > + struct hynitron_ts_data *ts_data = i2c_get_clientdata(client);
>> > + unsigned char buf[28];
>> > + unsigned char finger_id, sw;
>> > + unsigned int input_x = 0;
>> > + unsigned int input_y = 0;
>> > + unsigned int input_w = 0;
>> > + int idx = 0;
>> > + int i, err;
>> > + int touch_cnt, end_byte;
>> > +
>> > + /* Read and validate the first bits of input data. */
>> > + err = cst3xx_i2c_read_register(client, CST3XX_TOUCH_DATA_PART_REG,
>> > + buf, 28);
>> > + if ((err < 0) || (buf[6] != CST3XX_TOUCH_DATA_CHK_VAL) ||
>> > + (buf[0] == CST3XX_TOUCH_DATA_CHK_VAL)) {
>> > + dev_err(&client->dev, "cst3xx touch read failure\n");
>> > + return;
>> > + }
>> > +
>> > + /* Report to the device we're done reading the touch data. */
>> > + err = cst3xx_finish_touch_read(client);
>> > + if (err < 0) {
>> > + dev_err(&client->dev, "cst3xx touch read failure\n");
>>
>> We are already printing in cst3xx_finish_touch_read(), no need to print
>> here again.
>
> Ack.
>
>>
>> > + return;
>> > + }
>> > +
>> > + touch_cnt = buf[5] & CST3XX_TOUCH_COUNT_MASK;
>> > +
>> > + /* If no touches registered, clear the input slots. */
>> > + if (touch_cnt == 0) {
>> > + input_mt_sync_frame(ts_data->input_dev);
>> > + input_sync(ts_data->input_dev);
>> > + return;
>> > + }
>> > +
>> > + /*
>> > + * Check the check bit of the last touch slot. The check bit is
>> > + * always present after touch point 1 for valid data, and then
>> > + * appears as the last byte after all other touch data.
>> > + */
>> > + if (touch_cnt > 1) {
>> > + end_byte = touch_cnt * 5 + 2;
>> > + if (buf[end_byte] != CST3XX_TOUCH_DATA_CHK_VAL) {
>> > + dev_err(&client->dev, "cst3xx touch read failure\n");
>> > + return;
>> > + }
>> > + }
>> > +
>> > + /* Parse through the buffer to capture touch data. */
>> > + for (i = 0; i < touch_cnt; i++) {
>> > + input_x = ((buf[idx + 1] << 4) | ((buf[idx + 3] >> 4) & 0x0f));
>> > + input_y = ((buf[idx + 2] << 4) | (buf[idx + 3] & 0x0f));
>> > + input_w = (buf[idx + 4] >> 3);
>> > + sw = (buf[idx] & 0x0f) >> 1;
>> > + finger_id = (buf[idx] >> 4) & 0x0f;
>> > +
>> > + /* Sanity check we don't have more fingers than we expect */
>> > + if (ts_data->pdata->max_touch_num < finger_id) {
>> > + dev_err(&client->dev, "cst3xx touch read failure\n");
>> > + break;
>> > + }
>> > +
>> > + /* sw value of 0 means no touch, 0x03 means touch */
>> > + if (sw == CST3XX_TOUCH_DATA_TOUCH_VAL)
>> > + cst3xx_touch_update(ts_data, finger_id,
>> > + input_x, input_y, input_w);
>> > +
>> > + idx += 5;
>> > +
>> > + /* Skip the 2 bits between point 1 and point 2 */
>> > + if (i == 0)
>> > + idx += 2;
>> > + }
>> > +
>> > + input_mt_sync_frame(ts_data->input_dev);
>> > + input_sync(ts_data->input_dev);
>> > +}
>> > +
>> > +static int cst3xx_input_dev_int(struct i2c_client *client)
>> > +{
>> > + struct hynitron_ts_data *ts_data = i2c_get_clientdata(client);
>> > + int err;
>> > +
>> > + ts_data->input_dev = devm_input_allocate_device(&ts_data->client->dev);
>> > + if (!ts_data->input_dev) {
>> > + dev_err(&ts_data->client->dev,
>> > + "Failed to allocate input device.\n");
>> > + return -ENOMEM;
>> > + }
>> > +
>> > + ts_data->input_dev->name = "Hynitron cst3xx Touchscreen";
>> > + ts_data->input_dev->phys = "input/ts";
>> > + ts_data->input_dev->id.bustype = BUS_I2C;
>> > +
>> > + input_set_drvdata(ts_data->input_dev, ts_data);
>> > +
>> > + input_set_capability(ts_data->input_dev, EV_ABS, ABS_MT_POSITION_X);
>> > + input_set_capability(ts_data->input_dev, EV_ABS, ABS_MT_POSITION_Y);
>> > + input_set_abs_params(ts_data->input_dev, ABS_MT_TOUCH_MAJOR,
>> > + 0, 255, 0, 0);
>> > +
>> > + touchscreen_parse_properties(ts_data->input_dev, true, &ts_data->prop);
>> > +
>> > + if (!ts_data->prop.max_x || !ts_data->prop.max_y) {
>> > + dev_err(&client->dev,
>> > + "Invalid x/y (%d, %d), using defaults\n",
>> > + ts_data->prop.max_x, ts_data->prop.max_y);
>> > + ts_data->prop.max_x = 1152;
>> > + ts_data->prop.max_y = 1920;
>> > + input_abs_set_max(ts_data->input_dev,
>> > + ABS_MT_POSITION_X, ts_data->prop.max_x);
>> > + input_abs_set_max(ts_data->input_dev,
>> > + ABS_MT_POSITION_Y, ts_data->prop.max_y);
>> > + }
>> > +
>> > + err = input_mt_init_slots(ts_data->input_dev,
>> > + ts_data->pdata->max_touch_num,
>> > + INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
>> > + if (err < 0) {
>> > + dev_err(&ts_data->client->dev,
>> > + "Input device registration failed\n");
>> > + return err;
>> > + }
>> > +
>> > + err = input_register_device(ts_data->input_dev);
>> > + if (err < 0) {
>> > + dev_err(&ts_data->client->dev,
>> > + "Input device registration failed\n");
>> > + return err;
>> > + }
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +static int hyn_probe(struct i2c_client *client)
>> > +{
>> > + struct hynitron_ts_data *ts_data;
>> > + int err;
>> > +
>> > + ts_data = devm_kzalloc(&client->dev, sizeof(*ts_data), GFP_KERNEL);
>> > + if (!ts_data)
>> > + return -ENOMEM;
>> > +
>> > + ts_data->client = client;
>> > + i2c_set_clientdata(client, ts_data);
>> > +
>> > + ts_data->reset_gpio = devm_gpiod_get(&client->dev,
>> > + "reset", GPIOD_OUT_LOW);
>> > + err = PTR_ERR_OR_ZERO(ts_data->reset_gpio);
>> > + if (err < 0) {
>> > + dev_err(&client->dev, "request reset gpio failed: %d\n", err);
>> > + return err;
>> > + }
>> > +
>> > + ts_data->pdata = of_device_get_match_data(&client->dev);
>> > + if (!ts_data->pdata)
>> > + return -EINVAL;
>> > +
>> > + hyn_reset_proc(client, 60);
>> > +
>> > + err = ts_data->pdata->bootloader_enter(client);
>> > + if (err < 0)
>> > + return err;
>> > +
>> > + err = ts_data->pdata->init_input(client);
>> > + if (err < 0)
>> > + return err;
>> > +
>> > + err = ts_data->pdata->firmware_info(client);
>> > + if (err < 0)
>> > + return err;
>> > +
>> > + err = devm_request_threaded_irq(&client->dev, client->irq, NULL,
>> > + hyn_interrupt_handler,
>> > + IRQF_ONESHOT,
>> > + "Hynitron Touch Int", client);
>> > + if (err < 0) {
>> > + dev_err(&client->dev, "failed to request IRQ\n");
>> > + return err;
>> > + }
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +static const struct hynitron_ts_chip_data cst3xx_data = {
>> > + .max_touch_num = 5,
>> > + .ic_chkcode = 0xcaca0000,
>> > + .firmware_info = &cst3xx_firmware_info,
>> > + .bootloader_enter = &cst3xx_bootloader_enter,
>> > + .init_input = &cst3xx_input_dev_int,
>> > + .report_touch = &cst3xx_touch_report,
>> > +};
>> > +
>> > +static const struct i2c_device_id hyn_tpd_id[] = {
>> > + { .name = "hynitron_ts", 0 },
>> > + { /* sentinel */ },
>> > +};
>> > +MODULE_DEVICE_TABLE(i2c, hyn_tpd_id);
>> > +
>> > +static const struct of_device_id hyn_dt_match[] = {
>> > + { .compatible = "hynitron,cst340", .data = &cst3xx_data },
>> > + { /* sentinel */ },
>> > +};
>> > +MODULE_DEVICE_TABLE(of, hyn_dt_match);
>> > +
>> > +static struct i2c_driver hynitron_i2c_driver = {
>> > + .driver = {
>> > + .name = "Hynitron-TS",
>> > + .of_match_table = of_match_ptr(hyn_dt_match),
>> > + .probe_type = PROBE_PREFER_ASYNCHRONOUS,
>> > + },
>> > + .id_table = hyn_tpd_id,
>> > + .probe_new = hyn_probe,
>> > +};
>> > +
>> > +module_i2c_driver(hynitron_i2c_driver);
>> > +
>> > +MODULE_AUTHOR("Chris Morgan");
>> > +MODULE_DESCRIPTION("Hynitron Touchscreen Driver");
>> > +MODULE_LICENSE("GPL");
>> > --
>> > 2.25.1
