Convert binding for the Microchip CAP11xx series HW to the YAML syntax.
Signed-off-by: David Heidelberg <david@xxxxxxx>
---
.../devicetree/bindings/input/cap11xx.txt | 78 ----------
.../bindings/input/microchip,cap11xx.yaml | 146 ++++++++++++++++++
2 files changed, 146 insertions(+), 78 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/input/cap11xx.txt
create mode 100644 Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
diff --git a/Documentation/devicetree/bindings/input/cap11xx.txt b/Documentation/devicetree/bindings/input/cap11xx.txt
deleted file mode 100644
index 8c67a0b5058d..000000000000
--- a/Documentation/devicetree/bindings/input/cap11xx.txt
+++ /dev/null
@@ -1,78 +0,0 @@
-Device tree bindings for Microchip CAP11xx based capacitive touch sensors
-
-The node for this device must be a child of a I2C controller node, as the
-device communication via I2C only.
-
-Required properties:
-
- compatible: Must contain one of:
- "microchip,cap1106"
- "microchip,cap1126"
- "microchip,cap1188"
-
- reg: The I2C slave address of the device.
-
- interrupts: Property describing the interrupt line the
- device's ALERT#/CM_IRQ# pin is connected to.
- The device only has one interrupt source.
-
-Optional properties:
-
- autorepeat: Enables the Linux input system's autorepeat
- feature on the input device.
-
- microchip,sensor-gain: Defines the gain of the sensor circuitry. This
- effectively controls the sensitivity, as a
- smaller delta capacitance is required to
- generate the same delta count values.
- Valid values are 1, 2, 4, and 8.
- By default, a gain of 1 is set.
-
- microchip,irq-active-high: By default the interrupt pin is active low
- open drain. This property allows using the active
- high push-pull output.
-
- linux,keycodes: Specifies an array of numeric keycode values to
- be used for the channels. If this property is
- omitted, KEY_A, KEY_B, etc are used as
- defaults. The array must have exactly six
- entries.
-
-Example:
-
-i2c_controller {
- cap1106@28 {
- compatible = "microchip,cap1106";
- interrupt-parent = <&gpio1>;
- interrupts = <0 0>;
- reg = <0x28>;
- autorepeat;
- microchip,sensor-gain = <2>;
-
- linux,keycodes = <103>, /* KEY_UP */
- <106>, /* KEY_RIGHT */
- <108>, /* KEY_DOWN */
- <105>, /* KEY_LEFT */
- <109>, /* KEY_PAGEDOWN */
- <104>; /* KEY_PAGEUP */
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- usr@0 {
- label = "cap11xx:green:usr0";
- reg = <0>;
- };
-
- usr@1 {
- label = "cap11xx:green:usr1";
- reg = <1>;
- };
-
- alive@2 {
- label = "cap11xx:green:alive";
- reg = <2>;
- linux,default_trigger = "heartbeat";
- };
- };
-}
diff --git a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
new file mode 100644
index 000000000000..89079c019794
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
@@ -0,0 +1,146 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/input/microchip,cap11xx.yaml#";
+$schema: "http://devicetree.org/meta-schemas/core.yaml#";
+
+title: Device tree bindings for Microchip CAP11xx based capacitive touch sensors
+
+description: |
+ The Microchip CAP1xxx Family of RightTouchTM multiple-channel capacitive
+ touch controllers and LED drivers. The device communication via I2C only.
+
+maintainers:
+ - Rob Herring <robh+dt@xxxxxxxxxx>
+
+properties:
+ compatible:
+ enum:
+ - microchip,cap1106
+ - microchip,cap1126
+ - microchip,cap1188
+
+ reg:
+ maxItems: 1
+
+ '#address-cells':
+ const: 1
+ '#size-cells':
+ const: 0
+
+ interrupts:
+ maxItems: 1
+ description: |
+ Property describing the interrupt line the
+ device's ALERT#/CM_IRQ# pin is connected to.
+ The device only has one interrupt source.
+
+ autorepeat:
+ description: |
+ Enables the Linux input system's autorepeat feature on the input device.
+
+ linux,keycodes:
+ minItems: 6
+ maxItems: 6
+ description: |
+ Specifies an array of numeric keycode values to
+ be used for the channels. If this property is
+ omitted, KEY_A, KEY_B, etc are used as defaults.
+ The array must have exactly six entries.
+
+ microchip,sensor-gain:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 1
+ enum: [1, 2, 4, 8]
+ description: |
+ Defines the gain of the sensor circuitry. This
+ effectively controls the sensitivity, as a
+ smaller delta capacitance is required to
+ generate the same delta count values.
+
+ microchip,irq-active-high:
+ type: boolean
+ description: |
+ By default the interrupt pin is active low
+ open drain. This property allows using the active
+ high push-pull output.
+
+patternProperties:
+ "^led@[0-7]$":
+ type: object
+ description: CAP11xx LEDs
+ $ref: ../leds/common.yaml#
+
+ properties:
+ reg:
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ label: true
+
+ linux,default-trigger: true
+
+ default-state: true
+
+ required:
+ - reg
+
+ additionalProperties: false
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - microchip,cap1106
+ then:
+ patternProperties:
+ "^led@[0-7]$": false
+
+required:
+ - compatible
+ - interrupts
+
+additionalProperties: false
+
+examples:
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cap1188@28 {
+ compatible = "microchip,cap1188";
+ interrupt-parent = <&gpio1>;
+ interrupts = <0 0>;
+ reg = <0x28>;
+ autorepeat;
+ microchip,sensor-gain = <2>;
+
+ linux,keycodes = <103>, /* KEY_UP */
+ <106>, /* KEY_RIGHT */
+ <108>, /* KEY_DOWN */
+ <105>, /* KEY_LEFT */
+ <109>, /* KEY_PAGEDOWN */
+ <104>; /* KEY_PAGEUP */
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ label = "cap11xx:green:usr0";
+ reg = <0>;
+ };
+
+ led@1 {
+ label = "cap11xx:green:usr1";
+ reg = <1>;
+ };
+
+ led@2 {
+ label = "cap11xx:green:alive";
+ reg = <2>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+ };
--
2.33.0
