Re: [PATCH] Input: ili210x - Set the device name according to the device model

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 9/2/21 2:39 PM, Rogerio Pimentel wrote:
On Wed, Sep 1, 2021 at 5:48 PM Marek Vasut <marex@xxxxxxx> wrote:

On 9/1/21 10:27 PM, Rogerio Pimentel wrote:
On Wed, Sep 1, 2021 at 4:46 PM Marek Vasut <marex@xxxxxxx> wrote:

On 9/1/21 9:22 PM, Rogerio Pimentel wrote:

[...]

diff --git a/drivers/input/touchscreen/ili210x.c b/drivers/input/touchscreen/ili210x.c
index 30576a5f2f04..ca7af4a6f588 100644
--- a/drivers/input/touchscreen/ili210x.c
+++ b/drivers/input/touchscreen/ili210x.c
@@ -19,6 +19,8 @@
    #define ILI251X_DATA_SIZE1  31
    #define ILI251X_DATA_SIZE2  20

+#define ILI_NAME_LEN         27
+
    /* Touchscreen commands */
    #define REG_TOUCHDATA               0x10
    #define REG_PANEL_INFO              0x20
@@ -394,6 +396,7 @@ static int ili210x_i2c_probe(struct i2c_client *client,
        struct input_dev *input;
        int error;
        unsigned int max_xy;
+     char *model_name;

        dev_dbg(dev, "Probing for ILI210X I2C Touschreen driver");

@@ -440,7 +443,11 @@ static int ili210x_i2c_probe(struct i2c_client *client,
        i2c_set_clientdata(client, priv);

        /* Setup input device */
-     input->name = "ILI210x Touchscreen";
+     input->name = "Ilitek         Touchscreen";
+     model_name = (char *)input->name;
+     snprintf(model_name, ILI_NAME_LEN, "Ilitek %s Touchscreen",

Which ilitek devices do you have available exactly ?

There is a firmware interface which does report the device type, but I
don't know whether it works on all the ilitek touchscreen devices. If it
does, then it could be used here to pull the type from the firmware and
then use this instead

snprintf(model_name, ILI_NAME_LEN, "Ilitek ILI%04x Touchscreen", type);

Try this command against the touch controller, it sends it command 0x61
and reads two bytes of the reply:
i2ctransfer -f -y 1 w1@0x41 0x61 r2
0x10 0x25 # <---- on ILI2510 it reports 0x25 0x10 in reverse

Thanks for the comments and suggestions. I'll make the changes and send V2.

Can you tell which ILI2xxx touch controller you have exactly ?

Now I have only the ILI2511. Will also have to support ILI2510 and ILI2118.

Can you share the output of the 'i2ctransfer' (from i2c-tools) command
above ?

# i2ctransfer -f -y 3 w1@0x41 0x61 r2
0x11 0x25

Nice, so this works at least with the 251x series. Let's see how the 2118 behaves, I bet you will get 0x18 0x21 there too.



[Index of Archives]     [Linux Media Devel]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Linux Wireless Networking]     [Linux Omap]

  Powered by Linux