Convert the TI TSC2004/TSC2005 DT bindings to YAML schema. Signed-off-by: Marek Vasut <marex@xxxxxxx> Cc: Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx> Cc: Michael Welling <mwelling@xxxxxxxx> Cc: Rob Herring <robh+dt@xxxxxxxxxx> Cc: kernel@xxxxxxxxxxxxxxxxxx Cc: linux-input@xxxxxxxxxxxxxxx To: devicetree@xxxxxxxxxxxxxxx --- V2: - Switch the license to (GPL-2.0-only OR BSD-2-Clause) --- .../input/touchscreen/ti,tsc2005.yaml | 128 ++++++++++++++++++ .../bindings/input/touchscreen/tsc2005.txt | 64 --------- 2 files changed, 128 insertions(+), 64 deletions(-) create mode 100644 Documentation/devicetree/bindings/input/touchscreen/ti,tsc2005.yaml delete mode 100644 Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti,tsc2005.yaml b/Documentation/devicetree/bindings/input/touchscreen/ti,tsc2005.yaml new file mode 100644 index 000000000000..082c8ab00fcb --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ti,tsc2005.yaml @@ -0,0 +1,128 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/ti,tsc2005.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments TSC2004 and TSC2005 touchscreen controller bindings + +maintainers: + - Marek Vasut <marex@xxxxxxx> + - Michael Welling <mwelling@xxxxxxxx> + +properties: + $nodename: + pattern: "^touchscreen(@.*)?$" + + compatible: + oneOf: + - const: "ti,tsc2004" + - const: "ti,tsc2005" + + reg: + description: | + I2C address when used on the I2C bus, or the SPI chip select index + when used on the SPI bus + + interrupts: + maxItems: 1 + + reset-gpios: + description: GPIO specifier for the controller reset line + + spi-max-frequency: + description: TSC2005 SPI bus clock frequency. + maximum: 25000000 + + ti,x-plate-ohms: + description: resistance of the touchscreen's X plates in ohm (defaults to 280) + $ref: /schemas/types.yaml#/definitions/uint32 + + ti,esd-recovery-timeout-ms: + description: | + if the touchscreen does not respond after the configured time + (in milli seconds), the driver will reset it. This is disabled + by default. + $ref: /schemas/types.yaml#/definitions/uint32 + + vio-supply: + description: Regulator specifier + + touchscreen-fuzz-pressure: true + touchscreen-fuzz-x: true + touchscreen-fuzz-y: true + touchscreen-max-pressure: true + touchscreen-size-x: true + touchscreen-size-y: true + +allOf: + - $ref: touchscreen.yaml# + - if: + properties: + compatible: + contains: + const: "ti,tsc2004" + then: + properties: + spi-max-frequency: false + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@48 { + compatible = "ti,tsc2004"; + reg = <0x48>; + vio-supply = <&vio>; + + reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; + interrupts-extended = <&gpio1 27 IRQ_TYPE_EDGE_RISING>; + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; + }; + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@0 { + compatible = "ti,tsc2005"; + spi-max-frequency = <6000000>; + reg = <0>; + + vio-supply = <&vio>; + + reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */ + interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt deleted file mode 100644 index b80c04b0e5c0..000000000000 --- a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt +++ /dev/null @@ -1,64 +0,0 @@ -* Texas Instruments tsc2004 and tsc2005 touchscreen controllers - -Required properties: - - compatible : "ti,tsc2004" or "ti,tsc2005" - - reg : Device address - - interrupts : IRQ specifier - - spi-max-frequency : Maximum SPI clocking speed of the device - (for tsc2005) - -Optional properties: - - vio-supply : Regulator specifier - - reset-gpios : GPIO specifier for the controller reset line - - ti,x-plate-ohms : integer, resistance of the touchscreen's X plates - in ohm (defaults to 280) - - ti,esd-recovery-timeout-ms : integer, if the touchscreen does not respond after - the configured time (in milli seconds), the driver - will reset it. This is disabled by default. - - properties defined in touchscreen.txt - -Example: - -&i2c3 { - tsc2004@48 { - compatible = "ti,tsc2004"; - reg = <0x48>; - vio-supply = <&vio>; - - reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; - interrupts-extended = <&gpio1 27 IRQ_TYPE_EDGE_RISING>; - - touchscreen-fuzz-x = <4>; - touchscreen-fuzz-y = <7>; - touchscreen-fuzz-pressure = <2>; - touchscreen-size-x = <4096>; - touchscreen-size-y = <4096>; - touchscreen-max-pressure = <2048>; - - ti,x-plate-ohms = <280>; - ti,esd-recovery-timeout-ms = <8000>; - }; -} - -&mcspi1 { - tsc2005@0 { - compatible = "ti,tsc2005"; - spi-max-frequency = <6000000>; - reg = <0>; - - vio-supply = <&vio>; - - reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */ - interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */ - - touchscreen-fuzz-x = <4>; - touchscreen-fuzz-y = <7>; - touchscreen-fuzz-pressure = <2>; - touchscreen-size-x = <4096>; - touchscreen-size-y = <4096>; - touchscreen-max-pressure = <2048>; - - ti,x-plate-ohms = <280>; - ti,esd-recovery-timeout-ms = <8000>; - }; -} -- 2.30.2
