Instead of using special-casing retrieval of number of X/Y electrodes based on the firmware, let's select default values and mark registers as non-existent on firmwares that do not support this operation. Also mark "report rate" register as non-existent for generic firmwares as having it set to 0 does not make sense. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx> --- drivers/input/touchscreen/edt-ft5x06.c | 43 ++++++++++---------------- 1 file changed, 17 insertions(+), 26 deletions(-) diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c index 6ff81d48da86..2eefbc2485bc 100644 --- a/drivers/input/touchscreen/edt-ft5x06.c +++ b/drivers/input/touchscreen/edt-ft5x06.c @@ -69,6 +69,9 @@ #define EDT_RAW_DATA_RETRIES 100 #define EDT_RAW_DATA_DELAY 1000 /* usec */ +#define EDT_DEFAULT_NUM_X 1024 +#define EDT_DEFAULT_NUM_Y 1024 + enum edt_pmode { EDT_PMODE_NOT_SUPPORTED, EDT_PMODE_HIBERNATE, @@ -977,8 +980,7 @@ static void edt_ft5x06_ts_get_defaults(struct device *dev, } } -static void -edt_ft5x06_ts_get_parameters(struct edt_ft5x06_ts_data *tsdata) +static void edt_ft5x06_ts_get_parameters(struct edt_ft5x06_ts_data *tsdata) { struct edt_reg_addr *reg_addr = &tsdata->reg_addr; @@ -997,21 +999,17 @@ edt_ft5x06_ts_get_parameters(struct edt_ft5x06_ts_data *tsdata) if (reg_addr->reg_report_rate != NO_REGISTER) tsdata->report_rate = edt_ft5x06_register_read(tsdata, reg_addr->reg_report_rate); - if (tsdata->version == EDT_M06 || - tsdata->version == EDT_M09 || - tsdata->version == EDT_M12) { + tsdata->num_x = EDT_DEFAULT_NUM_X; + if (reg_addr->reg_num_x != NO_REGISTER) tsdata->num_x = edt_ft5x06_register_read(tsdata, reg_addr->reg_num_x); + tsdata->num_y = EDT_DEFAULT_NUM_Y; + if (reg_addr->reg_num_y != NO_REGISTER) tsdata->num_y = edt_ft5x06_register_read(tsdata, reg_addr->reg_num_y); - } else { - tsdata->num_x = -1; - tsdata->num_y = -1; - } } -static void -edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata) +static void edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata) { struct edt_reg_addr *reg_addr = &tsdata->reg_addr; @@ -1041,22 +1039,25 @@ edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata) case EV_FT: reg_addr->reg_threshold = EV_REGISTER_THRESHOLD; + reg_addr->reg_report_rate = NO_REGISTER; reg_addr->reg_gain = EV_REGISTER_GAIN; reg_addr->reg_offset = NO_REGISTER; reg_addr->reg_offset_x = EV_REGISTER_OFFSET_X; reg_addr->reg_offset_y = EV_REGISTER_OFFSET_Y; reg_addr->reg_num_x = NO_REGISTER; reg_addr->reg_num_y = NO_REGISTER; - reg_addr->reg_report_rate = NO_REGISTER; break; case GENERIC_FT: /* this is a guesswork */ reg_addr->reg_threshold = M09_REGISTER_THRESHOLD; + reg_addr->reg_report_rate = NO_REGISTER; reg_addr->reg_gain = M09_REGISTER_GAIN; reg_addr->reg_offset = M09_REGISTER_OFFSET; reg_addr->reg_offset_x = NO_REGISTER; reg_addr->reg_offset_y = NO_REGISTER; + reg_addr->reg_num_x = NO_REGISTER; + reg_addr->reg_num_y = NO_REGISTER; break; } } @@ -1195,20 +1196,10 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client, input->id.bustype = BUS_I2C; input->dev.parent = &client->dev; - if (tsdata->version == EDT_M06 || - tsdata->version == EDT_M09 || - tsdata->version == EDT_M12) { - input_set_abs_params(input, ABS_MT_POSITION_X, - 0, tsdata->num_x * 64 - 1, 0, 0); - input_set_abs_params(input, ABS_MT_POSITION_Y, - 0, tsdata->num_y * 64 - 1, 0, 0); - } else { - /* Unknown maximum values. Specify via devicetree */ - input_set_abs_params(input, ABS_MT_POSITION_X, - 0, 65535, 0, 0); - input_set_abs_params(input, ABS_MT_POSITION_Y, - 0, 65535, 0, 0); - } + input_set_abs_params(input, ABS_MT_POSITION_X, + 0, tsdata->num_x * 64 - 1, 0, 0); + input_set_abs_params(input, ABS_MT_POSITION_Y, + 0, tsdata->num_y * 64 - 1, 0, 0); touchscreen_parse_properties(input, true, &tsdata->prop); -- 2.29.2.576.ga3fc446d84-goog -- Dmitry