Re: [PATCH v2] HID: i2c-hid: Use block reads when possible to save power

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Jun 16, 2020 at 09:02:54PM +0300, Andi Shyti wrote:
> Hi Sultan,
> 
> > > > > so the only strategy available up until now has been to always retrieve
> > > > > the maximum possible report length over i2c, which can be quite
> > > > > inefficient. For devices that send reports in block read format, the i2c
> > > > > controller driver can read the payload length on the fly and terminate
> > > > > the i2c transaction early, resulting in considerable power savings.
> > > > > 
> > > > > On a Dell Precision 15 5540 with an i9-9880H, resting my finger on the
> > > > > touchpad causes psys power readings to go up by about 4W and hover there
> > > > > until I remove my finger. With this patch, my psys readings go from 4.7W
> > > > > down to 3.1W, yielding about 1.6W in savings. This is because my
> > > > > touchpad's max report length is 60 bytes, but all of the regular reports
> > > > > it sends for touch events are only 32 bytes, so the i2c transfer is
> > > > > roughly halved for the common case.
> > > > 
> > > > > +	/* Try to do a block read if the size fits in one byte */
> > > > > +	flags = size > 255 ? I2C_M_RD : I2C_M_RD | I2C_M_RECV_LEN;
> > > > 
> > > > AFAIR SMBus specification tells about 256. Why 255?
> > > > 
> > > > Andi, am I correct?
> > > 
> > > Actually the SMBUS 3.0 protocol from 2015[*] says 255:
> > > 
> > > "
> > > D.6 255 Bytes in Process Call
> > > 
> > > The maximum number of bytes allowed in the Block Write-Block Read
> > > Process Call (Section 6.5.8) was increased from 32 to 255.
> > > "
> > > 
> > > But why does it matter... I see the patch is detatching itself
> > > from smbus.
> > > 
> > > And, actually, I wonder if this is the right way to fix it, isn't
> > > it better to fix smbus instead?
> > 
> > I think the best solution would be to modify the i2c api to allow passing in a
> > function pointer and a payload size length, to specify how to interpret the size
> > of the incoming payload, so the adapter could handle both the HID over i2c
> > transfer spec and SMBus block reads without needing to read more bytes than
> > needed.
> 
> Can't you do that by specifying the xfer function?
> 
> When you use smbus_read/write in block or byte or whatever, smbus
> always checks if there is an xfer function specified and uses
> that.
> 
> If it's not specified it uses the default smbus functions with
> the limitations that come with it.

The xfer functions are specified on a per-adapter basis. In the case of i2c-hid,
we need to tell the adapter to interpret the payload size in a specific way,
which I *think* is only specific to HID over i2c (i.e., using 16 bits to store
the length and then checking it for device quirks).

> > For example, for an SMBus block read, the payload size is specified in the first
> > byte and it is limited to 32 bytes. However, for HID over i2c, the payload size
> > is specified in the first two bytes, and there are also some device quirks
> > involved to reinterpret the reported size.
> 
> which is wrong. The 32 bytes limitation is outdated: in the link
> that I gave before (i.e.  this one [*]), the new SMBUS specifies
> 255 maximum for read/write block.

Oops. But still, for SMBus block reads, the size is limited to 8 bits. For HID
over i2c, it can be 16 bits. I don't see how we can handle this without some api
cooperation to tell the adapter what the caller is expecting to see.

> > A nice solution would be to pass in how many bytes the i2c payload size can
> > contain, as well as a function pointer to evaluate the reported payload size in
> > a way that the caller wants. This would require modifying every i2c adapter
> > driver to add this functionality, but it would fix the efficiency problem faced
> > by i2c-hid and perhaps others.
> > 
> > > I have a patch ready that fixes the smbus transfer size, perhaps
> > > I should rebase, test and send it.
> > 
> > For the i2c-hid driver?
> 
> No, sorry, for smbus.
> 
> Now... here you are replacing "i2c_master_recv" with
> "i2c_transfer_buffer_flags". I do not really like this change,
> although I understand it's necessary, because we are bypassing
> the real issue that is that the smbus implementation is outdated.
> 
> I have a patch for that that for a matter of time I never sent.

Can it handle block reads (8 bit size) and HID over i2c (16 bit size)?

Sultan



[Index of Archives]     [Linux Media Devel]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Linux Wireless Networking]     [Linux Omap]

  Powered by Linux