On Thu, Jul 05, 2018 at 03:14:22PM +0000, Pascal PAILLET-LME wrote:
> From: pascal paillet <p.paillet@xxxxxx>
>
> stpmu1 is a pmic from STMicroelectronics. The stpmu1 integrates 10
> regulators and 3 switches with various capabilities.
>
> Signed-off-by: pascal paillet <p.paillet@xxxxxx>
> ---
> .../devicetree/bindings/mfd/st,stpmu1.txt | 138 +++++++++++++++++++++
> 1 file changed, 138 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/st,stpmu1.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/st,stpmu1.txt b/Documentation/devicetree/bindings/mfd/st,stpmu1.txt
> new file mode 100644
> index 0000000..53bdab4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/st,stpmu1.txt
> @@ -0,0 +1,138 @@
> +* STMicroelectronics STPMU1 Power Management IC
> +
> +Required parent device properties:
> +- compatible: "st,stpmu1"
> +- reg: the I2C slave address for the stpmu1 chip
> +- interrupts-extended: interrupt lines to use: second irq is for wakeup.
> +- #interrupt-cells: should be 2.
> +- interrupt-controller: describes the STPMU1 as an interrupt
> + controller (has its own domain). interrupt number are the following:
> + /* Interrupt Register 1 (0x50 for latch) */
> + IT_SWOUT_R=0
> + IT_SWOUT_F=1
> + IT_VBUS_OTG_R=2
> + IT_VBUS_OTG_F=3
> + IT_WAKEUP_R=4
> + IT_WAKEUP_F=5
> + IT_PONKEY_R=6
> + IT_PONKEY_F=7
> + /* Interrupt Register 2 (0x51 for latch) */
> + IT_OVP_BOOST=8
> + IT_OCP_BOOST=9
> + IT_OCP_SWOUT=10
> + IT_OCP_OTG=11
> + IT_CURLIM_BUCK4=12
> + IT_CURLIM_BUCK3=13
> + IT_CURLIM_BUCK2=14
> + IT_CURLIM_BUCK1=15
> + /* Interrupt Register 3 (0x52 for latch) */
> + IT_SHORT_SWOUT=16
> + IT_SHORT_SWOTG=17
> + IT_CURLIM_LDO6=18
> + IT_CURLIM_LDO5=19
> + IT_CURLIM_LDO4=20
> + IT_CURLIM_LDO3=21
> + IT_CURLIM_LDO2=22
> + IT_CURLIM_LDO1=23
> + /* Interrupt Register 3 (0x52 for latch) */
> + IT_SWIN_R=24
> + IT_SWIN_F=25
> + IT_RESERVED_1=26
> + IT_RESERVED_2=27
> + IT_VINLOW_R=28
> + IT_VINLOW_F=29
> + IT_TWARN_R=30
> + IT_TWARN_F=31
> +
> +Optional parent device properties:
> +- st,main_control_register:
s/_/-/
And elsewhere...
> + -bit 1: Power cycling will be performed on turn OFF condition
> + -bit 2: PWRCTRL is functional
> + -bit 3: PWRCTRL active high
> +- st,pads_pull_register:
> + -bit 1: WAKEUP pull down is not active
> + -bit 2: PWRCTRL pull up is active
> + -bit 3: PWRCTRL pull down is active
> + -bit 4: WAKEUP detector is disabled
> +- st,vin_control_register:
> + -bit 0: VINLOW monitoring is enabled
> + -bit [1...3]: VINLOW rising threshold
> + 000 VINOK_f + 50mV
> + 001 VINOK_f + 100mV
> + 010 VINOK_f + 150mV
> + 011 VINOK_f + 200mV
> + 100 VINOK_f + 250mV
> + 101 VINOK_f + 300mV
> + 110 VINOK_f + 350mV
> + 111 VINOK_f + 400mV
> + -bit [4...5]: VINLOW hyst
> + 00 100mV
> + 01 200mV
> + 10 300mV
> + 11 400mV
> + -bit 6: SW_OUT detector is disabled
> + -bit 7: SW_IN detector is enabled.
> +- st,usb_control_register:
> + -bit 3: SW_OUT current limit
> + 0: 600mA
> + 1: 1.1A
> + -bit 4: VBUS_OTG discharge is enabled
> + -bit 5: SW_OUT discharge is enabled
> + -bit 6: VBUS_OTG detection is enabled
> + -bit 7: BOOST_OVP is disabled
Just dumping register values into DT is not the greatest design.
> +
> +
> +stpmu1 consists is a varied group of sub-devices:
> +
> +Device Description
> +------ ------------
> +stpmu1-onkey : On key
> +stpmu1-regulators : Regulators
> +stpmu1-wdt : Watchdog
These should match the node name below.
> +
> +each sub-device bindings is be described in associated driver
> +documentation section.
> +
> +Example:
> +
> +pmic: stpmu1@33 {
> + compatible = "st,stpmu1";
> + reg = <0x33>;
> + interrupts = <0 2>;
> + interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_NONE>,
> + <&exti 55 1>;
> + st,version_status = <0x10>;
> + st,main_control_register=<0x0c>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + onkey {
> + compatible = "st,stpmu1-onkey";
> + interrupt-parent = <&pmic>;
> + interrupts = <7 0>,<6 1>;
> + st,onkey-pwroff-enabled;
> + st,onkey-press-seconds = <10>;
IIRC, we have some standard properties for these.
> + };
> +
> + watchdog {
> + compatible = "st,stpmu1-wdt";
> + };
> +
> + regulators {
> + compatible = "st,stpmu1-regulators";
> +
> + vdd_core: regulator@0 {
unit-address without reg is not valid. regulator-buck1, etc. instead.
> + regulator-compatible = "buck1";
> + regulator-name = "vdd_core";
> + regulator-boot-on;
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1200000>;
> + };
> + vdd: regulator@1 {
> + regulator-compatible = "buck3";
> + regulator-name = "vdd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-pull-down;
> + };
> + };
> --
> 1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
