[PATCH 4/8] regulator: stpmu1: add stpmu1 regulator driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: pascal paillet <p.paillet@xxxxxx>

The stpmu1 PMIC embeds several regulators and witches with
different capabilities.

Signed-off-by: pascal paillet <p.paillet@xxxxxx>
---
 drivers/regulator/Kconfig            |  12 +
 drivers/regulator/Makefile           |   2 +
 drivers/regulator/stpmu1_regulator.c | 919 +++++++++++++++++++++++++++++++++++
 3 files changed, 933 insertions(+)
 create mode 100644 drivers/regulator/stpmu1_regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 5dbccf5..0b508f5 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -804,6 +804,18 @@ config REGULATOR_TI_ABB
 	  on TI SoCs may be unstable without enabling this as it provides
 	  device specific optimized bias to allow/optimize functionality.
 
+config REGULATOR_STPMU1
+	tristate "ST Microelectronics STPMU1 PMIC Regulators"
+	depends on MFD_STPMU1
+	help
+	  This driver supports ST Microelectronics STPMU1 PMIC voltage
+	  regulators and switches. The STPMU1 regulators supply power to
+	  an application processor as well as to external system
+	  peripherals such as DDR, Flash memories and system devices.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called stpmu1_regulator.
+
 config REGULATOR_STW481X_VMMC
 	bool "ST Microelectronics STW481X VMMC regulator"
 	depends on MFD_STW481X || COMPILE_TEST
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index bd818ce..3d572ae 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_OF) += of_regulator.o
 obj-$(CONFIG_REGULATOR_FIXED_VOLTAGE) += fixed.o
 obj-$(CONFIG_REGULATOR_VIRTUAL_CONSUMER) += virtual.o
 obj-$(CONFIG_REGULATOR_USERSPACE_CONSUMER) += userspace-consumer.o
+obj-$(CONFIG_PROTECTION_CONSUMER) += protection-consumer.o
 
 obj-$(CONFIG_REGULATOR_88PG86X) += 88pg86x.o
 obj-$(CONFIG_REGULATOR_88PM800) += 88pm800.o
@@ -100,6 +101,7 @@ obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
 obj-$(CONFIG_REGULATOR_SC2731) += sc2731-regulator.o
 obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o
 obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
+obj-$(CONFIG_REGULATOR_STPMU1) += stpmu1_regulator.o
 obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
 obj-$(CONFIG_REGULATOR_SY8106A) += sy8106a-regulator.o
 obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o
diff --git a/drivers/regulator/stpmu1_regulator.c b/drivers/regulator/stpmu1_regulator.c
new file mode 100644
index 0000000..aed778b
--- /dev/null
+++ b/drivers/regulator/stpmu1_regulator.c
@@ -0,0 +1,919 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) STMicroelectronics 2018 - All Rights Reserved
+ * Author: Philippe Peurichard <philippe.peurichard@xxxxxx>,
+ * Pascal Paillet <p.paillet@xxxxxx> for STMicroelectronics.
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/stpmu1.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+
+/**
+ * stpmu1 regulator description
+ * @desc: regulator framework description
+ * @valid_modes_mask: modes supported by the regulator
+ * @valid_ops_mask: ops supported by the regulator
+ * @pull_down_reg: pull down register address
+ * @mask_reset_reg: mask reset register address
+ * @mask_reset_mask: mask rank and mask reset register mask
+ * @icc_reg: icc register address
+ * @icc_mask: icc register mask
+ */
+struct stpmu1_regulator_cfg {
+	struct regulator_desc desc;
+
+	unsigned int valid_modes_mask;
+	unsigned int valid_ops_mask;
+	u8 mask_reset_reg;
+	u8 mask_reset_mask;
+	u8 icc_reg;
+	u8 icc_mask;
+};
+
+/**
+ * stpmu1 regulator data: this structure is used as driver data
+ * @regul_id: regulator id
+ * @reg_node: DT node of regulator (unused on non-DT platforms)
+ * @cfg: stpmu specific regulator description
+ * @voltage_ref_reg: Special case for Vref DDR & LDO3 for which voltage
+ * depends on Buck2
+ * @mask_reset: mask_reset bit value
+ * @irq_curlim: current limit interrupt number
+ * @regmap: point to parent regmap structure
+ */
+struct stpmu1_regulator {
+	unsigned int regul_id;
+	struct device_node *reg_node;
+	struct stpmu1_regulator_cfg *cfg;
+	struct regulator_dev *voltage_ref_reg;
+	u8 mask_reset;
+	int irq_curlim;
+	struct regmap *regmap;
+};
+
+/**
+ * struct stpmu1_device_data - contains all regulators data
+ * @regulator_table : contains all the regulators
+ * @num_regulators: number of regulators used
+ */
+struct stpmu1_device_data {
+	struct stpmu1_regulator *regulator_table;
+	int num_regulators;
+};
+
+static int stpmu1_set_mode(struct regulator_dev *rdev, unsigned int mode);
+static unsigned int stpmu1_get_mode(struct regulator_dev *rdev);
+static int stpmu1_set_icc(struct regulator_dev *rdev);
+static int stpmu1_set_bypass(struct regulator_dev *rdev, bool enable);
+static int stpmu1_regulator_parse_dt(void *driver_data);
+static unsigned int stpmu1_regulator_get_max_volt(struct regulator_desc *desc);
+static unsigned int stpmu1_map_mode(unsigned int mode);
+static int stpmu1_ldo3_list_voltage(struct regulator_dev *rdev,
+				    unsigned int sel);
+static int stpmu1_ldo3_get_voltage(struct regulator_dev *rdev);
+static int stpmu1_fixed_regul_get_voltage(struct regulator_dev *rdev);
+
+enum {
+	STPMU1_BUCK1 = 0,
+	STPMU1_BUCK2 = 1,
+	STPMU1_BUCK3 = 2,
+	STPMU1_BUCK4 = 3,
+	STPMU1_LDO1 = 4,
+	STPMU1_LDO2 = 5,
+	STPMU1_LDO3 = 6,
+	STPMU1_LDO4 = 7,
+	STPMU1_LDO5 = 8,
+	STPMU1_LDO6 = 9,
+	STPMU1_VREF_DDR = 10,
+	STPMU1_BOOST = 11,
+	STPMU1_VBUS_OTG = 12,
+	STPMU1_SW_OUT = 13,
+};
+
+/*
+ * PMIC Ramp_delay: Time to settle down after voltage change (unit: uV/us)
+ * or enable
+ * is 3.6mV/uS +/-60%  -> 2.25mV/uS worst case
+ */
+#define PMIC_RAMP_SLOPE_UV_PER_US 2250
+/* Enable time is 5000V/2250mV/uS */
+#define PMIC_ENABLE_TIME_US 2200
+
+struct regulator_linear_range buck1_ranges[] = {
+	REGULATOR_LINEAR_RANGE(600000, 0, 30, 25000),
+	REGULATOR_LINEAR_RANGE(1350000, 31, 63, 0),
+};
+
+struct regulator_linear_range buck2_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1000000, 0, 17, 0),
+	REGULATOR_LINEAR_RANGE(1050000, 18, 19, 0),
+	REGULATOR_LINEAR_RANGE(1100000, 20, 21, 0),
+	REGULATOR_LINEAR_RANGE(1150000, 22, 23, 0),
+	REGULATOR_LINEAR_RANGE(1200000, 24, 25, 0),
+	REGULATOR_LINEAR_RANGE(1250000, 26, 27, 0),
+	REGULATOR_LINEAR_RANGE(1300000, 28, 29, 0),
+	REGULATOR_LINEAR_RANGE(1350000, 30, 31, 0),
+	REGULATOR_LINEAR_RANGE(1400000, 32, 33, 0),
+	REGULATOR_LINEAR_RANGE(1450000, 34, 35, 0),
+	REGULATOR_LINEAR_RANGE(1500000, 36, 63, 0),
+};
+
+struct regulator_linear_range buck3_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1000000, 0, 19, 0),
+	REGULATOR_LINEAR_RANGE(1100000, 20, 23, 0),
+	REGULATOR_LINEAR_RANGE(1200000, 24, 27, 0),
+	REGULATOR_LINEAR_RANGE(1300000, 28, 31, 0),
+	REGULATOR_LINEAR_RANGE(1400000, 32, 35, 0),
+	REGULATOR_LINEAR_RANGE(1500000, 36, 55, 100000),
+	REGULATOR_LINEAR_RANGE(3400000, 56, 63, 0),
+
+};
+
+struct regulator_linear_range buck4_ranges[] = {
+	REGULATOR_LINEAR_RANGE(600000, 0, 27, 25000),
+	REGULATOR_LINEAR_RANGE(1300000, 28, 29, 0),
+	REGULATOR_LINEAR_RANGE(1350000, 30, 31, 0),
+	REGULATOR_LINEAR_RANGE(1400000, 32, 33, 0),
+	REGULATOR_LINEAR_RANGE(1450000, 34, 35, 0),
+	REGULATOR_LINEAR_RANGE(1500000, 36, 60, 100000),
+	REGULATOR_LINEAR_RANGE(3900000, 61, 63, 0),
+
+};
+
+struct regulator_linear_range ldo1_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1700000, 0, 7, 0),
+	REGULATOR_LINEAR_RANGE(1700000, 8, 24, 100000),
+	REGULATOR_LINEAR_RANGE(3300000, 25, 31, 0),
+
+};
+
+struct regulator_linear_range ldo2_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1700000, 0, 7, 0),
+	REGULATOR_LINEAR_RANGE(1700000, 8, 24, 100000),
+	REGULATOR_LINEAR_RANGE(3300000, 25, 30, 0),
+
+};
+
+struct regulator_linear_range ldo3_ranges[] = {
+	/* Special case to allow range to cover lowest value of Buck2/2 */
+	REGULATOR_LINEAR_RANGE(500000, 0, 0, 0),
+	REGULATOR_LINEAR_RANGE(1700000, 1, 7, 0),
+	REGULATOR_LINEAR_RANGE(1700000, 8, 24, 100000),
+	/* index 31 is special case when LDO3 is in mode DDR */
+	REGULATOR_LINEAR_RANGE(3300000, 25, 31, 0),
+};
+
+struct regulator_linear_range ldo5_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1700000, 0, 7, 0),
+	REGULATOR_LINEAR_RANGE(1700000, 8, 30, 100000),
+	REGULATOR_LINEAR_RANGE(3900000, 31, 31, 0),
+};
+
+struct regulator_linear_range ldo6_ranges[] = {
+	REGULATOR_LINEAR_RANGE(900000, 0, 24, 100000),
+	REGULATOR_LINEAR_RANGE(3300000, 25, 31, 0),
+};
+
+static struct regulator_ops stpmu1_ldo_ops = {
+	.list_voltage = regulator_list_voltage_linear_range,
+	.map_voltage = regulator_map_voltage_linear_range,
+	.is_enabled = regulator_is_enabled_regmap,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.set_pull_down = regulator_set_pull_down_regmap,
+	.set_over_current_protection = stpmu1_set_icc,
+};
+
+static struct regulator_ops stpmu1_ldo3_ops = {
+	.list_voltage = stpmu1_ldo3_list_voltage,
+	.map_voltage = regulator_map_voltage_iterate,
+	.is_enabled = regulator_is_enabled_regmap,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.get_voltage = stpmu1_ldo3_get_voltage,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.set_pull_down = regulator_set_pull_down_regmap,
+	.get_bypass = regulator_get_bypass_regmap,
+	.set_bypass = stpmu1_set_bypass,
+	.set_over_current_protection = stpmu1_set_icc,
+};
+
+static struct regulator_ops stpmu1_ldo4_fixed_regul_ops = {
+	.is_enabled = regulator_is_enabled_regmap,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.set_pull_down = regulator_set_pull_down_regmap,
+	.set_over_current_protection = stpmu1_set_icc,
+};
+
+static struct regulator_ops stpmu1_buck_ops = {
+	.list_voltage = regulator_list_voltage_linear_range,
+	.map_voltage = regulator_map_voltage_linear_range,
+	.is_enabled = regulator_is_enabled_regmap,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.set_pull_down = regulator_set_pull_down_regmap,
+	.set_mode = stpmu1_set_mode,
+	.get_mode = stpmu1_get_mode,
+	.set_over_current_protection = stpmu1_set_icc,
+};
+
+static struct regulator_ops stpmu1_fixed_regul_ops = {
+	.is_enabled = regulator_is_enabled_regmap,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.get_voltage = stpmu1_fixed_regul_get_voltage,
+	.set_pull_down = regulator_set_pull_down_regmap,
+};
+
+static struct regulator_ops stpmu1_switch_regul_ops = {
+	.is_enabled = regulator_is_enabled_regmap,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.get_voltage = stpmu1_fixed_regul_get_voltage,
+	.set_over_current_protection = stpmu1_set_icc,
+};
+
+#define REG_LDO(ids, base) { \
+	.name = #ids, \
+	.id = STPMU1_##ids, \
+	.n_voltages = 32, \
+	.ops = &stpmu1_ldo_ops, \
+	.linear_ranges = base ## _ranges, \
+	.n_linear_ranges = ARRAY_SIZE(base ## _ranges), \
+	.type = REGULATOR_VOLTAGE, \
+	.owner = THIS_MODULE, \
+	.vsel_reg = ids##_ACTIVE_CR, \
+	.vsel_mask = LDO_VOLTAGE_MASK, \
+	.enable_reg = ids##_ACTIVE_CR, \
+	.enable_mask = LDO_ENABLE_MASK, \
+	.enable_val = 1, \
+	.disable_val = 0, \
+	.pull_down_reg = ids##_PULL_DOWN_REG, \
+	.pull_down_mask = ids##_PULL_DOWN_MASK, \
+	.supply_name = #base, \
+}
+
+#define REG_LDO3(ids) { \
+	.name = #ids, \
+	.id = STPMU1_##ids, \
+	.n_voltages = 32, \
+	.ops = &stpmu1_ldo3_ops, \
+	.linear_ranges = ldo3_ranges, \
+	.n_linear_ranges = ARRAY_SIZE(ldo3_ranges), \
+	.type = REGULATOR_VOLTAGE, \
+	.owner = THIS_MODULE, \
+	.vsel_reg = LDO3_ACTIVE_CR, \
+	.vsel_mask = LDO_VOLTAGE_MASK, \
+	.enable_reg = LDO3_ACTIVE_CR, \
+	.enable_mask = LDO_ENABLE_MASK, \
+	.enable_val = 1, \
+	.disable_val = 0, \
+	.bypass_reg = LDO3_ACTIVE_CR, \
+	.bypass_mask = LDO_BYPASS_MASK, \
+	.bypass_val_on = LDO_BYPASS_MASK, \
+	.bypass_val_off = 0, \
+	.pull_down_reg = ids##_PULL_DOWN_REG, \
+	.pull_down_mask = ids##_PULL_DOWN_MASK, \
+	.supply_name = "ldo3", \
+}
+
+#define REG_LDO4(ids) { \
+	.name = #ids, \
+	.id = STPMU1_##ids, \
+	.n_voltages = 1, \
+	.ops = &stpmu1_ldo4_fixed_regul_ops, \
+	.type = REGULATOR_VOLTAGE, \
+	.owner = THIS_MODULE, \
+	.min_uV = 3300000, \
+	.fixed_uV = 3300000, \
+	.enable_reg = LDO4_ACTIVE_CR, \
+	.enable_mask = LDO_ENABLE_MASK, \
+	.enable_val = 1, \
+	.disable_val = 0, \
+	.pull_down_reg = ids##_PULL_DOWN_REG, \
+	.pull_down_mask = ids##_PULL_DOWN_MASK, \
+	.supply_name = "ldo4", \
+}
+
+#define REG_BUCK(ids, base) { \
+	.name = #ids, \
+	.id = STPMU1_##ids, \
+	.ops = &stpmu1_buck_ops, \
+	.n_voltages = 64, \
+	.linear_ranges = base ## _ranges, \
+	.n_linear_ranges = ARRAY_SIZE(base ## _ranges), \
+	.type = REGULATOR_VOLTAGE, \
+	.owner = THIS_MODULE, \
+	.vsel_reg = ids##_ACTIVE_CR, \
+	.vsel_mask = BUCK_VOLTAGE_MASK, \
+	.enable_reg = ids##_ACTIVE_CR, \
+	.enable_mask = BUCK_ENABLE_MASK, \
+	.enable_val = 1, \
+	.disable_val = 0, \
+	.of_map_mode = stpmu1_map_mode, \
+	.pull_down_reg = ids##_PULL_DOWN_REG, \
+	.pull_down_mask = ids##_PULL_DOWN_MASK, \
+	.supply_name = #base, \
+}
+
+#define REG_VREF_DDR(ids, reg) { \
+	.name = #ids, \
+	.id = STPMU1_##ids, \
+	.n_voltages = 1, \
+	.ops = &stpmu1_fixed_regul_ops, \
+	.type = REGULATOR_VOLTAGE, \
+	.owner = THIS_MODULE, \
+	.min_uV = 0, \
+	.fixed_uV = 5000000, \
+	.enable_reg = (reg), \
+	.enable_mask = BUCK_ENABLE_MASK, \
+	.enable_val = 1, \
+	.disable_val = 0, \
+	.of_map_mode = stpmu1_map_mode, \
+	.pull_down_reg = ids##_PULL_DOWN_REG, \
+	.pull_down_mask = ids##_PULL_DOWN_MASK, \
+	.supply_name = NULL, \
+}
+
+#define REG_SWITCH(ids, base, reg, mask, val) { \
+	.name = #ids, \
+	.id = STPMU1_##ids, \
+	.n_voltages = 1, \
+	.ops = &stpmu1_switch_regul_ops, \
+	.type = REGULATOR_VOLTAGE, \
+	.owner = THIS_MODULE, \
+	.min_uV = 0, \
+	.fixed_uV = 5000000, \
+	.enable_reg = (reg), \
+	.enable_mask = (mask), \
+	.enable_val = (val), \
+	.disable_val = 0, \
+	.of_map_mode = stpmu1_map_mode, \
+	.supply_name = #base, \
+}
+
+struct stpmu1_regulator_cfg stpmu1_regulator_cfgs[] = {
+	[STPMU1_BUCK1] = {
+		.desc = REG_BUCK(BUCK1, buck1),
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+				  REGULATOR_CHANGE_MODE,
+		.valid_modes_mask = REGULATOR_MODE_NORMAL |
+				    REGULATOR_MODE_STANDBY,
+		.icc_reg = BUCKS_ICCTO_CR,
+		.icc_mask = BIT(0),
+		.mask_reset_reg = BUCKS_MASK_RESET_CR,
+		.mask_reset_mask = BIT(0),
+	},
+	[STPMU1_BUCK2] = {
+		.desc = REG_BUCK(BUCK2, buck2),
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+				  REGULATOR_CHANGE_MODE,
+		.valid_modes_mask = REGULATOR_MODE_NORMAL |
+				    REGULATOR_MODE_STANDBY,
+		.icc_reg = BUCKS_ICCTO_CR,
+		.icc_mask = BIT(1),
+		.mask_reset_reg = BUCKS_MASK_RESET_CR,
+		.mask_reset_mask = BIT(1),
+	},
+	[STPMU1_BUCK3] = {
+		.desc = REG_BUCK(BUCK3, buck3),
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+				  REGULATOR_CHANGE_MODE,
+		.valid_modes_mask = REGULATOR_MODE_NORMAL |
+				    REGULATOR_MODE_STANDBY,
+		.icc_reg = BUCKS_ICCTO_CR,
+		.icc_mask = BIT(2),
+		.mask_reset_reg = BUCKS_MASK_RESET_CR,
+		.mask_reset_mask = BIT(2),
+	},
+	[STPMU1_BUCK4] = {
+		.desc = REG_BUCK(BUCK4, buck4),
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+				  REGULATOR_CHANGE_MODE,
+		.valid_modes_mask = REGULATOR_MODE_NORMAL |
+				    REGULATOR_MODE_STANDBY,
+		.icc_reg = BUCKS_ICCTO_CR,
+		.icc_mask = BIT(3),
+		.mask_reset_reg = BUCKS_MASK_RESET_CR,
+		.mask_reset_mask = BIT(3),
+	},
+	[STPMU1_LDO1] = {
+		.desc = REG_LDO(LDO1, ldo1),
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+		.icc_reg = LDOS_ICCTO_CR,
+		.icc_mask = BIT(0),
+		.mask_reset_reg = LDOS_MASK_RESET_CR,
+		.mask_reset_mask = BIT(0),
+	},
+	[STPMU1_LDO2] = {
+		.desc = REG_LDO(LDO2, ldo2),
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+		.icc_reg = LDOS_ICCTO_CR,
+		.icc_mask = BIT(1),
+		.mask_reset_reg = LDOS_MASK_RESET_CR,
+		.mask_reset_mask = BIT(1),
+	},
+	[STPMU1_LDO3] = {
+		.desc = REG_LDO3(LDO3),
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+				  REGULATOR_CHANGE_BYPASS,
+		.icc_reg = LDOS_ICCTO_CR,
+		.icc_mask = BIT(2),
+		.mask_reset_reg = LDOS_MASK_RESET_CR,
+		.mask_reset_mask = BIT(2),
+	},
+	[STPMU1_LDO4] = {
+		.desc = REG_LDO4(LDO4),
+		.icc_reg = LDOS_ICCTO_CR,
+		.icc_mask = BIT(3),
+		.mask_reset_reg = LDOS_MASK_RESET_CR,
+		.mask_reset_mask = BIT(3),
+	},
+	[STPMU1_LDO5] = {
+		.desc = REG_LDO(LDO5, ldo5),
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+		.icc_reg = LDOS_ICCTO_CR,
+		.icc_mask = BIT(4),
+		.mask_reset_reg = LDOS_MASK_RESET_CR,
+		.mask_reset_mask = BIT(4),
+	},
+	[STPMU1_LDO6] = {
+		.desc = REG_LDO(LDO6, ldo6),
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+		.icc_reg = LDOS_ICCTO_CR,
+		.icc_mask = BIT(5),
+		.mask_reset_reg = LDOS_MASK_RESET_CR,
+		.mask_reset_mask = BIT(5),
+	},
+	[STPMU1_VREF_DDR] = {
+		.desc = REG_VREF_DDR(VREF_DDR, VREF_DDR_ACTIVE_CR),
+		.mask_reset_reg = LDOS_MASK_RESET_CR,
+		.mask_reset_mask = BIT(6),
+	},
+	[STPMU1_BOOST] = {
+		.desc = REG_SWITCH(BOOST, boost, BST_SW_CR,
+				   BOOST_ENABLED,
+				   BOOST_ENABLED),
+		.icc_reg = BUCKS_ICCTO_CR,
+		.icc_mask = BIT(6),
+	},
+	[STPMU1_VBUS_OTG] = {
+		.desc = REG_SWITCH(VBUS_OTG, pwr_sw1, BST_SW_CR,
+				   USBSW_OTG_SWITCH_ENABLED,
+				   USBSW_OTG_SWITCH_ENABLED),
+		.icc_reg = BUCKS_ICCTO_CR,
+		.icc_mask = BIT(4),
+	},
+	[STPMU1_SW_OUT] = {
+		.desc = REG_SWITCH(SW_OUT, pwr_sw2, BST_SW_CR,
+				   SWIN_SWOUT_ENABLED,
+				   SWIN_SWOUT_ENABLED),
+		.icc_reg = BUCKS_ICCTO_CR,
+		.icc_mask = BIT(5),
+	},
+};
+
+#define GET_MINIMUM_VOLTAGE(_regulator_desc_ptr) \
+	((_regulator_desc_ptr)->linear_ranges[0].min_uV)
+
+static unsigned int stpmu1_map_mode(unsigned int mode)
+{
+	return mode == REGULATOR_MODE_STANDBY ?
+		REGULATOR_MODE_STANDBY : REGULATOR_MODE_NORMAL;
+}
+
+static unsigned int stpmu1_regulator_get_max_volt(struct regulator_desc *desc)
+{
+	const struct regulator_linear_range *last_range =
+		&desc->linear_ranges[desc->n_linear_ranges - 1];
+
+	unsigned int max_voltage =
+		last_range->min_uV +
+		(last_range->max_sel - last_range->min_sel + 1)
+		* last_range->uV_step;
+
+	return max_voltage;
+}
+
+static int stpmu1_get_voltage_regmap(struct regulator_dev *rdev)
+{
+	int selector = 0;
+
+	if (!rdev)
+		return -EINVAL;
+	selector = regulator_get_voltage_sel_regmap(rdev);
+	return regulator_list_voltage_linear_range(rdev, selector);
+}
+
+static int stpmu1_ldo3_list_voltage(struct regulator_dev *rdev,
+				    unsigned int sel)
+{
+	struct stpmu1_regulator *regul = rdev_get_drvdata(rdev);
+
+	if (sel == 0)
+		return regulator_list_voltage_linear_range(rdev, 1);
+
+	if (sel < 31)
+		return regulator_list_voltage_linear_range(rdev, sel);
+
+	if (sel == 31)
+		return stpmu1_get_voltage_regmap(regul->voltage_ref_reg) / 2;
+
+	return -EINVAL;
+}
+
+static int stpmu1_ldo3_get_voltage(struct regulator_dev *rdev)
+{
+	int sel = regulator_get_voltage_sel_regmap(rdev);
+
+	if (sel < 0)
+		return -EINVAL;
+
+	return stpmu1_ldo3_list_voltage(rdev, (unsigned int)sel);
+}
+
+static int stpmu1_fixed_regul_get_voltage(struct regulator_dev *rdev)
+{
+	struct stpmu1_regulator *regul = rdev_get_drvdata(rdev);
+	int id = rdev_get_id(rdev);
+
+	/* VREF_DDR voltage is equal to Buck2/2 */
+	if (id == STPMU1_VREF_DDR)
+		return stpmu1_get_voltage_regmap(regul->voltage_ref_reg) / 2;
+
+	/* For all other case , rely on fixed value defined by Hw settings */
+	return regul->cfg->desc.fixed_uV;
+}
+
+static int stpmu1_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	struct stpmu1_regulator *regul = rdev_get_drvdata(rdev);
+	unsigned int hplp;
+
+	/* The low power mode will be set for NORMAL/RUN registers */
+	switch (mode) {
+	case REGULATOR_MODE_NORMAL:
+		hplp = 0;
+		break;
+	case REGULATOR_MODE_STANDBY:
+		hplp = 1;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return  regmap_update_bits(regul->regmap, regul->cfg->desc.enable_reg,
+				   BUCK_HPLP_ENABLE_MASK,
+				   hplp << BUCK_HPLP_SHIFT);
+}
+
+static unsigned int stpmu1_get_mode(struct regulator_dev *rdev)
+{
+	struct stpmu1_regulator *regul = rdev_get_drvdata(rdev);
+	int ret;
+	unsigned int val;
+
+	ret = regmap_read(regul->regmap, regul->cfg->desc.enable_reg, &val);
+	if (ret < 0)
+		return ret;
+
+	val &= BUCK_HPLP_ENABLE_MASK;
+	val >>= BUCK_HPLP_SHIFT;
+
+	return val ? REGULATOR_MODE_STANDBY : REGULATOR_MODE_NORMAL;
+}
+
+static int stpmu1_set_icc(struct regulator_dev *rdev)
+{
+	struct stpmu1_regulator *regul = rdev_get_drvdata(rdev);
+
+	/* enable switch off in case of over current */
+	return regmap_update_bits(regul->regmap, regul->cfg->icc_reg,
+				  regul->cfg->icc_mask, regul->cfg->icc_mask);
+}
+
+static int stpmu1_set_bypass(struct regulator_dev *rdev, bool enable)
+{
+	struct stpmu1_regulator *regul = rdev_get_drvdata(rdev);
+	int ret;
+	unsigned int val;
+
+	if (enable)
+		val = regul->cfg->desc.bypass_val_on;
+	else
+		val = regul->cfg->desc.bypass_val_off;
+
+	ret = regmap_update_bits(regul->regmap, regul->cfg->desc.bypass_reg,
+				 regul->cfg->desc.bypass_mask, val);
+
+	return ret;
+}
+
+static irqreturn_t stpmu1_curlim_irq_handler(int irq, void *data)
+{
+	struct regulator_dev *rdev = (struct regulator_dev *)data;
+
+	mutex_lock(&rdev->mutex);
+
+	/* Send an overcurrent notification */
+	regulator_notifier_call_chain(rdev,
+				      REGULATOR_EVENT_OVER_CURRENT,
+				      NULL);
+
+	mutex_unlock(&rdev->mutex);
+
+	return IRQ_HANDLED;
+}
+
+static int stpmu1_regulator_init(struct platform_device *pdev,
+				 struct regulator_dev *rdev)
+{
+	struct stpmu1_regulator *regul = rdev_get_drvdata(rdev);
+	int ret = 0;
+
+	/* set mask reset */
+	if (regul->mask_reset && regul->cfg->mask_reset_reg != 0) {
+		ret = regmap_update_bits(regul->regmap,
+					 regul->cfg->mask_reset_reg,
+					 regul->cfg->mask_reset_mask,
+					 regul->cfg->mask_reset_mask);
+		if (ret) {
+			dev_err(&pdev->dev, "set mask reset failed\n");
+			return ret;
+		}
+	}
+
+	/* setup an irq handler for over-current detection */
+	if (regul->irq_curlim >= 0) {
+		ret = devm_request_threaded_irq(&pdev->dev,
+						regul->irq_curlim, NULL,
+						stpmu1_curlim_irq_handler,
+						IRQF_ONESHOT | IRQF_SHARED,
+						pdev->name, rdev);
+		if (ret) {
+			dev_err(&pdev->dev, "Request IRQ failed\n");
+			return ret;
+		}
+	}
+	return 0;
+}
+
+#define MATCH(_name, _id) \
+	[STPMU1_##_id] = { \
+		.name = #_name, \
+		.desc = &stpmu1_regulator_cfgs[STPMU1_##_id].desc, \
+	}
+
+static struct of_regulator_match stpmu1_regulators_matches[] = {
+	MATCH(buck1, BUCK1),
+	MATCH(buck2, BUCK2),
+	MATCH(buck3, BUCK3),
+	MATCH(buck4, BUCK4),
+	MATCH(ldo1, LDO1),
+	MATCH(ldo2, LDO2),
+	MATCH(ldo3, LDO3),
+	MATCH(ldo4, LDO4),
+	MATCH(ldo5, LDO5),
+	MATCH(ldo6, LDO6),
+	MATCH(vref_ddr, VREF_DDR),
+	MATCH(boost, BOOST),
+	MATCH(pwr_sw1, VBUS_OTG),
+	MATCH(pwr_sw2, SW_OUT),
+};
+
+static inline struct device_node *match_of_node(struct platform_device *pdev,
+						int index)
+{
+	if (!stpmu1_regulators_matches[index].of_node)
+		dev_info(&pdev->dev,
+			 "DT node not found for regulator %i\n\r", index);
+
+	return stpmu1_regulators_matches[index].of_node;
+}
+
+static int stpmu1_regulator_parse_dt(void *driver_data)
+{
+	struct stpmu1_regulator *regul =
+		(struct stpmu1_regulator *)driver_data;
+
+	if (!regul)
+		return -EINVAL;
+
+	if (of_get_property(regul->reg_node, "st,mask_reset", NULL))
+		regul->mask_reset = 1;
+
+	regul->irq_curlim = of_irq_get(regul->reg_node, 0);
+
+	return 0;
+}
+
+static void update_regulator_constraints(int index,
+					 struct regulator_init_data *init_data)
+{
+	struct stpmu1_regulator_cfg *cfg = &stpmu1_regulator_cfgs[index];
+	struct regulator_desc *desc = &cfg->desc;
+
+	init_data->constraints.valid_ops_mask |=
+		cfg->valid_ops_mask;
+	init_data->constraints.valid_modes_mask |=
+		cfg->valid_modes_mask;
+
+	/*
+	 * if all constraints are not specified in DT , ensure Hw
+	 * constraints are met
+	 */
+	if (desc->n_voltages > 1) {
+		if (!init_data->constraints.min_uV)
+			init_data->constraints.min_uV =
+				GET_MINIMUM_VOLTAGE(desc);
+		if (!init_data->constraints.max_uV)
+			init_data->constraints.max_uV =
+			stpmu1_regulator_get_max_volt(desc);
+	}
+
+	if (!init_data->constraints.ramp_delay)
+		init_data->constraints.ramp_delay = PMIC_RAMP_SLOPE_UV_PER_US;
+
+	if (!init_data->constraints.enable_time)
+		init_data->constraints.enable_time = PMIC_ENABLE_TIME_US;
+}
+
+static struct
+regulator_dev *stpmu1_regulator_register(struct platform_device *pdev, int id,
+					 struct regulator_init_data *init_data,
+					 struct stpmu1_regulator *regul,
+					 struct regulator_dev *buck2)
+{
+	struct stpmu1_dev *pmic_dev = dev_get_drvdata(pdev->dev.parent);
+	struct regulator_dev *rdev;
+	struct regulator_config config = {};
+
+	config.dev = &pdev->dev;
+	config.init_data = init_data;
+	config.of_node = match_of_node(pdev, id);
+	config.regmap = pmic_dev->regmap;
+	config.driver_data = regul;
+
+	regul->regul_id = id;
+	regul->reg_node = config.of_node;
+	regul->cfg = &stpmu1_regulator_cfgs[id];
+	regul->regmap = pmic_dev->regmap;
+
+	/* LDO3 and VREF_DDR can use buck2 as reference voltage */
+	if (regul->regul_id == STPMU1_LDO3 ||
+	    regul->regul_id == STPMU1_VREF_DDR) {
+		if (!buck2) {
+			dev_err(&pdev->dev,
+				"Error in PMIC regulator settings: Buck2 is not defined prior to LDO3 or VREF_DDR regulators\n"
+				);
+			return ERR_PTR(-EINVAL);
+		}
+		regul->voltage_ref_reg = buck2;
+	}
+
+	rdev = devm_regulator_register(&pdev->dev, &regul->cfg->desc, &config);
+	if (IS_ERR(rdev)) {
+		dev_err(&pdev->dev, "failed to register %s regulator\n",
+			regul->cfg->desc.name);
+	}
+
+	return rdev;
+}
+
+static int stpmu1_regulator_probe(struct platform_device *pdev)
+{
+	struct stpmu1_dev *pmic_dev = dev_get_drvdata(pdev->dev.parent);
+	struct stpmu1_device_data *ddata;
+	struct regulator_dev *rdev;
+	struct stpmu1_regulator *regul;
+	struct regulator_init_data *init_data;
+	struct device_node *np;
+	int i, ret;
+	struct regulator_dev *buck2_rdev = NULL;
+
+	ddata = devm_kzalloc(&pdev->dev, sizeof(struct stpmu1_device_data),
+			     GFP_KERNEL);
+	if (!ddata)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, ddata);
+
+	/* disable icc for all reguls */
+	ret = regmap_update_bits(pmic_dev->regmap, BUCKS_ICCTO_CR,
+				 BUCKS_ICCTO_CR_REG_MASK, 0);
+	if (ret == 0)
+		ret = regmap_update_bits(pmic_dev->regmap, LDOS_ICCTO_CR,
+					 LDOS_ICCTO_CR_REG_MASK, 0);
+	/* reset pulldown value */
+	if (ret == 0)
+		ret = regmap_update_bits(pmic_dev->regmap, BUCKS_PD_CR,
+					 BUCKS_PD_CR_REG_MASK, 0);
+	if (ret == 0)
+		ret = regmap_update_bits(pmic_dev->regmap, LDO14_PD_CR,
+					 LDO1234_PULL_DOWN_REGISTER_MASK, 0);
+	if (ret == 0)
+		ret = regmap_update_bits(pmic_dev->regmap, LDO56_VREF_PD_CR,
+					 LDO56_VREF_PD_CR_REG_MASK, 0);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"failed to update stpmu1 register %d\n", ret);
+		return ret;
+	}
+
+	np = pdev->dev.of_node;
+	if (!np) {
+		dev_err(&pdev->dev, "regulators node not found\n");
+		return -EINVAL;
+	}
+
+	ret = of_regulator_match(&pdev->dev, np,
+				 stpmu1_regulators_matches,
+				 ARRAY_SIZE(stpmu1_regulators_matches));
+	if (ret < 0) {
+		dev_err(&pdev->dev,
+			"Error in PMIC regulator device tree node");
+		return ret;
+	}
+	ddata->num_regulators = ret;
+
+	dev_dbg(&pdev->dev, "%d regulator(s) found in DT\n",
+		ddata->num_regulators);
+
+	regul = devm_kzalloc(&pdev->dev, ddata->num_regulators *
+			     sizeof(struct stpmu1_regulator),
+			     GFP_KERNEL);
+	if (!regul)
+		return -ENOMEM;
+
+	ddata->regulator_table = regul;
+
+	/* Register all defined (from DT) regulators to Regulator Framework */
+	for (i = 0; i < ARRAY_SIZE(stpmu1_regulator_cfgs); i++) {
+		/* Parse DT & find regulators to register */
+		init_data = stpmu1_regulators_matches[i].init_data;
+		if (init_data) {
+			init_data->regulator_init = &stpmu1_regulator_parse_dt;
+
+			update_regulator_constraints(i, init_data);
+
+			rdev = stpmu1_regulator_register(pdev, i, init_data,
+							 regul, buck2_rdev);
+			if (IS_ERR(rdev))
+				return PTR_ERR(rdev);
+
+			ret = stpmu1_regulator_init(pdev, rdev);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"failed to initialize regulator %d\n",
+					ret);
+				return ret;
+			}
+
+			if (regul->regul_id == STPMU1_BUCK2)
+				buck2_rdev = rdev;
+
+			regul++;
+		}
+	}
+
+	dev_dbg(&pdev->dev, "stpmu1_regulator driver probed\n");
+
+	return 0;
+}
+
+static const struct of_device_id of_pmic_regulator_match[] = {
+	{ .compatible = "st,stpmu1-regulators" },
+	{ },
+};
+
+MODULE_DEVICE_TABLE(of, of_pmic_regulator_match);
+
+static struct platform_driver stpmu1_regulator_driver = {
+	.driver = {
+		.name = "stpmu1-regulator",
+		.of_match_table = of_match_ptr(of_pmic_regulator_match),
+	},
+	.probe = stpmu1_regulator_probe,
+};
+
+module_platform_driver(stpmu1_regulator_driver);
+
+MODULE_DESCRIPTION("STPMU1 PMIC voltage regulator driver");
+MODULE_AUTHOR("<philippe.peurichard@xxxxxx>");
+MODULE_LICENSE("GPL");
-- 
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Media Devel]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Linux Wireless Networking]     [Linux Omap]

  Powered by Linux