Hello,
This patch series is a rework of my previous series named:
[PATCH 00/14] iio: triggers: add consumer support
In few words, this is the implementation of splitting the functionality
of the IP block ADC device in SAMA5D2 SoC from ADC with touchscreen
support. In order to avoid having a MFD device, two separate
drivers that would work on same register base and split the IRQ,etc,
as advised on the mailing list, I created a consumer driver for the
channels, that will connect to the ADC as described in the device tree.
I have collected feedback from everyone and here is the result:
I have added a new generic resistive touchscreen driver, which acts
as a iio consumer for the given channels and will create an input
device and report the events. It uses a callback buffer to register
to the IIO device and waits for data to be pushed.
Inside the IIO device, I have kept a similar approach with the first version
of the series, except that now the driver can take multiple buffers, and
will configure the touchscreen part of the hardware device if the specific
channels are requested.
The SAMA5D2 ADC driver registers three new channels: two for the
position on the X and Y axis, and one for the touch pressure.
When channels are requested, it will check if the touchscreen channel mask
includes the requested channels (it is possible that the consumer driver
will not request pressure for example). If it's the case, it will work
in touchscreen mode, and will refuse to do usual analog-digital conversion,
because we have a single trigger and the touchscreen needs it.
When the scan mask will include only old channels, the driver will function
in the same way as before. If the scan mask somehow is a mix of the two (the
masks intersect), the driver will refuse to work whatsoever (cannot have both
in the same time).
The driver allows reading raw data for the new channels, if claim direct
mode works: no touchscreen driver requested anything. The new channels can
act like the old ones. However, when requesting these channels, the usual
trigger will not work and will not be enabled. The touchscreen channels
require special trigger and irq configuration: pen detect, no pen detect
and a periodic trigger to sample the touchscreen position and pressure.
If the user attempts to use another trigger while there is a buffer
that already requested the touchscreen channels (thus the trigger), the
driver will refuse to comply.
In order to have defines for the channel numbers, I added a bindings include
file that goes on a separate commit :
dt-bindings: iio: adc: at91-sama5d2_adc: add channel specific consumer info
This should go in the same tree with the following commits :
ARM: dts: at91: sama5d2: add channel cells for ADC device
ARM: dts: at91: sama5d2: Add resistive touch device
as build will break because these commits depend on the binding one
which creates the included header file.
After the discussions earlier this year on the mailing list, I hope this
rework of the patches is much better and fulfills all the requirements
for this implementation.
Eugen Hristev (10):
MAINTAINERS: add generic resistive touchscreen adc
iio: Add channel for Position Relative
dt-bindings: input: touchscreen: touch_adc: create bindings
iio: inkern: add module put/get on iio dev module when requesting
channels
iio: adc: at91-sama5d2_adc: fix channel configuration for differential
channels
iio: adc: at91-sama5d2_adc: add support for position and pressure
channels
input: touchscreen: touch_adc: add generic resistive ADC touchscreen
dt-bindings: iio: adc: at91-sama5d2_adc: add channel specific consumer
info
ARM: dts: at91: sama5d2: add channel cells for ADC device
ARM: dts: at91: sama5d2: Add resistive touch device
Documentation/ABI/testing/sysfs-bus-iio | 12 +
.../bindings/iio/adc/at91-sama5d2_adc.txt | 9 +
.../bindings/input/touchscreen/touch_adc.txt | 33 ++
MAINTAINERS | 6 +
arch/arm/boot/dts/sama5d2.dtsi | 12 +
drivers/iio/adc/at91-sama5d2_adc.c | 491 ++++++++++++++++++++-
drivers/iio/industrialio-core.c | 1 +
drivers/iio/inkern.c | 8 +-
drivers/input/touchscreen/Kconfig | 13 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/touch_adc.c | 199 +++++++++
include/dt-bindings/iio/adc/at91-sama5d2_adc.h | 16 +
include/uapi/linux/iio/types.h | 1 +
tools/iio/iio_event_monitor.c | 2 +
14 files changed, 791 insertions(+), 13 deletions(-)
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/touch_adc.txt
create mode 100644 drivers/input/touchscreen/touch_adc.c
create mode 100644 include/dt-bindings/iio/adc/at91-sama5d2_adc.h
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
