Re: [REGRESSION] Touchpad failure after e7348396c6d5 ("Input: ALPS - fix V8+ protocol handling (73 03 28)")

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



I get the same results as you - x_max and y_max affect cursor speed, and x_res and y_res seem to have no effect.  I can't seem to come up with any values that cause intermittent cursor issues on one side of the touchpad.
Both max and res do get passed up to the X driver, and I do see references to both max and resolution in xf86-input-evdev, although I haven't actually traced it through to see if/where each value is actually consumed with my setup.

Maybe we should ask the user to try a few more tests?
1) Using the original code (without the modifications from bug 195215), add the following before 'return 0' at the end of alps_update_device_area_ss4_v2(), then run `dmesg | grep num-electrodes` after loading the alps kernel module to get the output.  This should tell us what values the user is actually reading from the hardware:
psmouse_err(psmouse,
    "pitch %dx%d num-electrodes %dx%d physical size %dx%dmm res %dx%d max %dx%d\n",
    x_pitch, y_pitch, num_x_electrode, num_y_electrode,
    x_phys / 10, y_phys / 10, priv->x_res, priv->y_res, priv->x_max, priv->y_max);
2) Use the old electrode count code but the new pitch code:
	if (IS_SS4PLUS_DEV(priv->dev_id)) {
		num_x_electrode =
			SS4_NUMSENSOR_XOFFSET + (otp[1][0] & 0x0F);
		num_y_electrode =
			SS4_NUMSENSOR_YOFFSET + ((otp[1][0] >> 4) & 0x0F);

		priv->x_max =
			(num_x_electrode - 1) * SS4_COUNT_PER_ELECTRODE;
		priv->y_max =
			(num_y_electrode - 1) * SS4_COUNT_PER_ELECTRODE;

		x_pitch = (otp[0][1] & 0x0F) + SS4PLUS_MIN_PITCH_MM;
		y_pitch = ((otp[0][1] >> 4) & 0x0F) + SS4PLUS_MIN_PITCH_MM;

	} else {
3) Use the new electrode count code but the old pitch code:
	if (IS_SS4PLUS_DEV(priv->dev_id)) {
		num_x_electrode =
			SS4PLUS_NUMSENSOR_XOFFSET + (otp[0][2] & 0x0F);
		num_y_electrode =
			SS4PLUS_NUMSENSOR_YOFFSET + ((otp[0][2] >> 4) & 0x0F);

		priv->x_max =
			(num_x_electrode - 1) * SS4PLUS_COUNT_PER_ELECTRODE;
		priv->y_max =
			(num_y_electrode - 1) * SS4PLUS_COUNT_PER_ELECTRODE;

		x_pitch = ((otp[1][2] >> 2) & 0x07) + SS4_MIN_PITCH_MM;
		y_pitch = ((otp[1][2] >> 5) & 0x07) + SS4_MIN_PITCH_MM;

	} else {

On Thu, Jun 15, 2017 at 12:33:29AM +0000, Masaki Ota wrote:
> Hi, Paul, Dmitry,
> 
> About Laura's test result, it seems like this issue has to do with x_max, y_max, x_res, y_res.
> This values are set as following code.
> 	input_set_abs_params(dev1, ABS_MT_POSITION_X, 0, priv->x_max, 0, 0);
> 	input_set_abs_params(dev1, ABS_MT_POSITION_Y, 0, priv->y_max, 0, 0);
> 
> 	input_abs_set_res(dev1, ABS_MT_POSITION_X, priv->x_res);
> 	input_abs_set_res(dev1, ABS_MT_POSITION_Y, priv->y_res);
> 
> For testing this code, I assigned an abnormal value to x_max, y_max , and it seems to effect only cursor speed.
> About x_res, y_res , there is no effect, even if I set an abnormal value.(need this code?)
> I don't understand why these values have to do with this issue.
> 
> Can you guess the root cause of this issue?
> 
> Best Regards,
> Masaki Ota
> -----Original Message-----
> From: Laura Abbott [mailto:labbott@xxxxxxxxxx] 
> Sent: Thursday, June 15, 2017 3:53 AM
> To: 太田 真喜 Masaki Ota <masaki.ota@xxxxxxxxxxx>; Paul Donohue <linux-kernel@xxxxxxxxxx>
> Cc: Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx>; Pali Rohar <pali.rohar@xxxxxxxxx>; Nick Fletcher <nick.m.fletcher@xxxxxxxxx>; linux-input@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; scott.s.lowe@xxxxxxxxx
> Subject: Re: [REGRESSION] Touchpad failure after e7348396c6d5 ("Input: ALPS - fix V8+ protocol handling (73 03 28)")
> 
> On 06/11/2017 10:25 PM, Masaki Ota wrote:
> > Hi, Laura,
> > 
> > Could you try to check below modification?
> > https://bugzilla.kernel.org/show_bug.cgi?id=195215#c10
> > 
> > This thread person said, the issue was fixed by this change.
> > I guess it's a XY coordinate setting problem, though the code that before the patch is applied also has a problem.
> > 
> 
> With the previous patch plus the part you suggested:
> 
> "it appears as if this resolves all remaining touchpad issues.
> Cursor movement works as expected, both on the left-hand and right-hand sides of the touchpad, and I did not see any issues with two-finger scrolling on either side of the touchpad. Behavior with this test build appeared to be identical to 4.10.5, the last "official" kernel release to work with my touchpad."
> 
> So it sounds like both parts together fix the issue.
> 
> Thanks,
> Laura
> 
> > Best Regards,
> > Masaki Ota
> > -----Original Message-----
> > From: Laura Abbott [mailto:labbott@xxxxxxxxxx]
> > Sent: Wednesday, June 07, 2017 1:59 AM
> > To: Paul Donohue <linux-kernel@xxxxxxxxxx>
> > Cc: 太田 真喜 Masaki Ota <masaki.ota@xxxxxxxxxxx>; Dmitry Torokhov 
> > <dmitry.torokhov@xxxxxxxxx>; Pali Rohar <pali.rohar@xxxxxxxxx>; Nick 
> > Fletcher <nick.m.fletcher@xxxxxxxxx>; linux-input@xxxxxxxxxxxxxxx; 
> > linux-kernel@xxxxxxxxxxxxxxx; scott.s.lowe@xxxxxxxxx
> > Subject: Re: [REGRESSION] Touchpad failure after e7348396c6d5 ("Input: 
> > ALPS - fix V8+ protocol handling (73 03 28)")
> > 
> > On 06/02/2017 09:03 PM, Paul Donohue wrote:
> >> This might be related to
> >> https://bugzilla.kernel.org/show_bug.cgi?id=195215
> >>
> >> Could you have the user try this change? 
> >> https://bugzilla.kernel.org/show_bug.cgi?id=195215#c12
> >>
> > 
> > https://bugzilla.redhat.com/show_bug.cgi?id=1447327#c13
> > 
> > "Cursor movement seems to work, but there are intermittent two-finger scrolling issues on the right-hand side of the touchpad. There are no issues with cursor movement or two-finger scrolling on the left-hand side of the touchpad."
> > 
> >> On Fri, Jun 02, 2017 at 10:54:52AM -0700, Laura Abbott wrote:
> >>> Hi,
> >>>
> >>> Fedora got a bug report
> >>> https://bugzilla.redhat.com/show_bug.cgi?id=1447327
> >>> of a touchpad failure on a Dell Latitude E7370. Testing showed that 
> >>> the bad commit was
> >>>
> >>> commit e7348396c6d51b57c95c6646c390cd078e038e19
> >>> Author: Masaki Ota <masaki.ota@xxxxxxxxxxx>
> >>> Date:   Fri Mar 17 14:10:57 2017 -0700
> >>>
> >>>     Input: ALPS - fix V8+ protocol handling (73 03 28)
> >>>     
> >>>     Devices identified as E7="73 03 28" use slightly modified version of V8
> >>>     protocol, with lower count per electrode, different offsets, and different
> >>>     feature bits in OTP data.
> >>>     
> >>>     Fixes: aeaa881f9b17 ("Input: ALPS - set DualPoint flag for 74 03 28 devices")
> >>>     Signed-off-by: Masaki Ota <masaki.ota@xxxxxxxxxxx>
> >>>     Acked-by: Pali Rohar <pali.rohar@xxxxxxxxx>
> >>>     Tested-by: Paul Donohue <linux-kernel@xxxxxxxxxx>
> >>>     Tested-by: Nick Fletcher <nick.m.fletcher@xxxxxxxxx>
> >>>     Cc: stable@xxxxxxxxxxxxxxx
> >>>     Signed-off-by: Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx>
> >>>
> >>> I suspect this particular model needs special handling as well?
> >>>
> >>> Thanks,
> >>> Laura
> >>>
> > 
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Media Devel]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Linux Wireless Networking]     [Linux Omap]

  Powered by Linux