From: Steve Twiss <stwiss.opensource@xxxxxxxxxxx> Extend existing DA9062 binding information to include the DA9061 PMIC for MFD core and regulators. Add a da9062-onkey link to the existing onkey binding file. Add a da9062-thermal link to the new temperature monitoring binding file. Delete the da9062-watchdog section and replace it with a link to the new DA9061/62 binding information file. Acked-by: Rob Herring <robh@xxxxxxxxxx> Signed-off-by: Steve Twiss <stwiss.opensource@xxxxxxxxxxx> --- This patch applies against linux-next and v4.11-rc3 v6 -> v7 - NO CODE CHANGE v5 -> v6 - NO CODE CHANGE - Rebased from v4.9 to v4.11-rc3 v4 -> v5 - NO CODE CHANGE - Rebased from v4.8 to v4.9 v3 -> v4 - Patch renamed from [PATCH V3 4/9] to [PATCH V4 3/8] - Remove double newline spacing in text file - Added Acked-by Rob Herring v2 -> v3 - Patch renamed from [PATCH V2 04/10] to [PATCH V3 4/9] - Ensure binding description concentrates on the device not the device driver - Separate the DA9061 and DA9062 sub-device tables to distinguish the difference between the two devices - Update the commit message to describe this change - Add e-mail information about associated patches from this set without describing them as being explicitly dependent on this binding v1 -> v2 - Patch renamed from [PATCH V1 09/10] to [PATCH V2 04/10] -- these changes were made to fix checkpatch warnings caused by the patch set dependency order Hi, Added an Ack from Rob Herring for the PATCH V3 version. As previously: Other information: The device driver from this patch set (associated with this binding) is - [PATCH V5 4/8] mfd: da9061: MFD core support and also the following binding file changes: - Binding for onkey (already applied by Dmitry Torokhov) - [PATCH V5 1/8] Binding for watchdog - [PATCH V5 2/8] Binding for thermal Regards, Steve Twiss, Dialog Semiconductor Documentation/devicetree/bindings/mfd/da9062.txt | 49 +++++++++++++++++------- 1 file changed, 36 insertions(+), 13 deletions(-) diff --git a/Documentation/devicetree/bindings/mfd/da9062.txt b/Documentation/devicetree/bindings/mfd/da9062.txt index 38802b5..c0a418c 100644 --- a/Documentation/devicetree/bindings/mfd/da9062.txt +++ b/Documentation/devicetree/bindings/mfd/da9062.txt @@ -1,22 +1,39 @@ * Dialog DA9062 Power Management Integrated Circuit (PMIC) -DA9062 consists of a large and varied group of sub-devices: +Product information for the DA9062 and DA9061 devices can be found here: +- http://www.dialog-semiconductor.com/products/da9062 +- http://www.dialog-semiconductor.com/products/da9061 + +The DA9062 PMIC consists of: Device Supply Names Description ------ ------------ ----------- da9062-regulator : : LDOs & BUCKs da9062-rtc : : Real-Time Clock +da9062-onkey : : On Key +da9062-watchdog : : Watchdog Timer +da9062-thermal : : Thermal + +The DA9061 PMIC consists of: + +Device Supply Names Description +------ ------------ ----------- +da9062-regulator : : LDOs & BUCKs +da9062-onkey : : On Key da9062-watchdog : : Watchdog Timer +da9062-thermal : : Thermal ====== Required properties: -- compatible : Should be "dlg,da9062". +- compatible : Should be + "dlg,da9062" for DA9062 + "dlg,da9061" for DA9061 - reg : Specifies the I2C slave address (this defaults to 0x58 but it can be modified to match the chip's OTP settings). - interrupt-parent : Specifies the reference to the interrupt controller for - the DA9062. + the DA9062 or DA9061. - interrupts : IRQ line information. - interrupt-controller @@ -25,8 +42,8 @@ further information on IRQ bindings. Sub-nodes: -- regulators : This node defines the settings for the LDOs and BUCKs. The - DA9062 regulators are bound using their names listed below: +- regulators : This node defines the settings for the LDOs and BUCKs. + The DA9062 regulators are bound using their names listed below: buck1 : BUCK_1 buck2 : BUCK_2 @@ -37,19 +54,29 @@ Sub-nodes: ldo3 : LDO_3 ldo4 : LDO_4 + The DA9061 regulators are bound using their names listed below: + + buck1 : BUCK_1 + buck2 : BUCK_2 + buck3 : BUCK_3 + ldo1 : LDO_1 + ldo2 : LDO_2 + ldo3 : LDO_3 + ldo4 : LDO_4 + The component follows the standard regulator framework and the bindings details of individual regulator device can be found in: Documentation/devicetree/bindings/regulator/regulator.txt - - rtc : This node defines settings required for the Real-Time Clock associated with the DA9062. There are currently no entries in this binding, however compatible = "dlg,da9062-rtc" should be added if a node is created. -- watchdog: This node defines the settings for the watchdog driver associated - with the DA9062 PMIC. The compatible = "dlg,da9062-watchdog" should be added - if a node is created. +- onkey : See ../input/da9062-onkey.txt + +- watchdog: See ../watchdog/da9062-watchdog.txt +- thermal : See ../thermal/da9062-thermal.txt Example: @@ -64,10 +91,6 @@ Example: compatible = "dlg,da9062-rtc"; }; - watchdog { - compatible = "dlg,da9062-watchdog"; - }; - regulators { DA9062_BUCK1: buck1 { regulator-name = "BUCK1"; -- end-of-patch for PATCH V7 -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
